Document Outline

• About This Guide
• Index
• About This Guide
  • Contents of the Guide
  • Conventions Used in This Guide
  • Related Publications
• Overview
  • System Description
• Installation
  • Unpacking the ANG-1000
    • Accessories
    • Location Planning
  • Connecting Cables
    • Ethernet Cables
      • Connecting an ANG-1000
        • 1 Do one of the following as shown in Figure7:
        • 2 Plug the opposite end of the blue Ethernet cable into a wall jack, patch panel, or hub linked t...
        • 3 Plug an orange, straight-through Ethernet cable into the External port as shown in Figure7.
        • 4 Plug the opposite end of this cable into a DSL or cable modem.
  • Connecting Power to the ANG-1000
    • 1 Plug the power supply cord into the system’s power socket as shown in Figure8.
    • 2 Plug the correct end of the AC power cord into the power supply and the other end into a ground...
  • Checking ANG-1000 Connections
    • Rear Panel Link LEDs
    • Front Panel LEDs
• Configuring the ANG-1000 with Aurorean Web Config
  • Before You Begin
  • Logging into Web Config
    • 1 Point your Web browser at the default trusted IP address of the ANG-1000. In the browser’s Loca...
    • 2 Type netadmin in the User Name and Password fields as shown in Figure14.
    • 3 Click the checkbox to save your password if you desire and click OK.
  • Viewing VPN Status
    • 1 Click the Firmware Upgrade menu option and go to the next page.
  • Downloading the Latest Firmware
    • 1 Click the Firmware Upgrade menu option.
    • 2 In the FTP server field, enter the name of the FTP server where the new ANG image is stored: an...
    • 3 Type the full path of the location of the Firmware image: /ang1000/ANG1000.bin
    • 4 Enter the Username anonymous
    • 5 Enter netadmin in the Password and Confirm fields and click Apply.
    • 6 Click Apply and watch the External/Trusted LEDs on the front panel blink displaying an inside/o...
    • 7 After downloading and “flashing “are complete, a status page displays as shown in Figure18 ind...
    • 8 Reboot the ANG-1000 by clicking Reboot Now.
    • 9 To ensure that the image was updated, compare the date last modified, Release, Build and Patch ...
  • Setting Up the VPN
    • 1 Click the VPN Setup menu option.
    • 1 Enter the Name of the remote ANG-3000/7000 you are connecting to.
    • 2 Enter the Gateway IP address of the remote ANG-3000/7000.
    • 3 Enter the Username on the remote ANG-3000/7000.
    • 4 Enter the Password on the remote ANG-3000/7000.
    • 5 Confirm the password on the remote ANG-3000/7000.
    • 6 Select the Connection type: either EZ-IPsec or PPTP.
    • 7 Optional. Click the Start network gateway now checkbox to create instant access or wait until t...
    • 8 Optional. Click Force default route under Global VPN Settings.
    • 9 Click Apply.
  • Setting Up the Internet Connection
    • 1 Click the Internet Setup menu option.
    • 2 Do one of the following:
    • 3 If you chose the Manual or PPPoE options, a window appears detailing the reconfiguration change...
  • Setting Up the LAN
    • 1 Click the LAN Setup menu option.
    • 2 Do one of the following:
    • 3 If you chose the DHCP option or changed the DNS or WINS default entries, a window appears detai...
  • Setting Up the Firewall
    • 1 Click the Firewall Setup menu option.
    • 2 Enable the option of your choice and click Apply.
  • Setting Your Password
    • 1 Click the Set Password menu option.
    • 2 Type the old Password in the field provided.
    • 3 Type a new Password in the field provided.
    • 4 Confirm the new password in the field provided.
    • 5 Click Apply.
  • Checking Device Status
    • 1 Click the Device Status menu option.
  • Using Advanced Utilities
    • 1 Click the Advanced Utilities menu option.
    • 2 Do one of the following:
  • Using the Configuration Editor
    • 1 Click the Configuration Edit menu option.
    • 2 Click on the command of your choice.
    • 3 The arguments of the command you selected are displayed in the Configuration File Edit window, ...
    • 4 Edit the UNIX command and click Update or Delete.
    • Configuring IP Port Forwarding
      • 1 Login to Web Config.
      • 2 Click on the Config File Editor menu option.
      • 3 Click on the ipfwrules Configuration File.
      • 4 In the Configuration File Edit window, scroll to the end of the file.
      • 5 Under **Expert-Config**, type the following rules:
      • 6 Click Update and Reboot Now when prompted to save the change.
• Glossary
• Specifications
• Pin Assignments
• License Agreement & Support
  • Enterasys Networks License Agreement
    • License Grant
    • Warranty
    • Infringement Indemnification
    • Limitation of Liability
    • Termination
    • International Provisions
    • Applicable Law
    • U. S. Government - Commercial Computer Software
  • Technical Support
    • Support from Enterasys Networks
      • On-line Services
      • Phone Support
    • Returning Products for Repair
• Index