Document Outline

• FRONT MATTER
• CONTENTS
• INTRODUCTION
  • VGA Utilities
  • Optional Equipment
    • Memory
    • Drives
    • OverDrive Processor
    • Alternate VGA Interface
  • How to Use This Manual
• CHAP 1-USING YOUR CHAPTER
  • Turning On the Computer
  • Turning Off the Computer
  • Using Disks and Disk Drives
    • How Disks Store Data
    • Types of Diskette Drives
    • Caring for Diskettes and Diskette Drives
    • Write-protecting Diskettes
    • Inserting and Removing Diskettes
    • Using a Sing/e Diskette Drive System
    • Formatting Diskettes
    • Making Backup Copies
    • Using a Hard Disk Drive
  • Special Keys on the Keyboard
  • Stopping a Command or Program
  • Resetting the Computer
  • Using a Password
    • Changing a Password
    • Deleting a Password
  • Using Your Computer a Network Server
    • Using a Password in Network Server Mode
  • Changing the Processor Speed
    • Entering Keyboard Commands
    • Using the ESPEED Program
  • Preparing the Hard Disk for Moving
  • Using AUTOEXEC. BAT and Other Batch Files
• CHAP 2-INSTALLING AND REMOVING OPTIONS
  • How to Use This Chapter
    • Locating the Internal Components
  • Removing the Cover
  • Changing the Jumper Settings
    • Setting the Jumpers
  • Memory Modules (SIMMs)
    • Inserting SIMMs
    • SIMMS
  • Installing an Option
  • Removing an Option Card
  • Removing the Option Card Connector Board
  • Replacing the Option Card Connector Board
  • Installing a New Processor Chip
  • Using the Alternate VGA
  • Replacing the Cover
  • Post-installation Procedures
• CHAP 3-INSTALLING AND REMOVING DRIVES
  • How to Use This Chapter
    • Setting the Hard Disk Drive Jumpers
      • Where to Go Next
    • Installing a Hard Disk in the Vertical Bay
      • Removing the Mounting Frames
      • Installing the Hard Disk
      • Connecting the Cables
    • Removing a Hard Disk From the Vertical
    • Installing a Drive in a Horizontal Bay
      • Attaching Mounting Frames to a Hard Disk
      • Installing the Drive
      • Connecting the Cables
    • Removing a Drive From a Horizontal Bay
    • Connecting the Hard Disk Drive Ribbon Cable to the System
    • Post-installation Procedures
• CHAP 4-RUNNING SYSTEM DIAGNOSTICS
  • Starting the Program
    • Deleting Tests
    • Adding Tests
  • Running Tests
    • Resuming From an Error
  • System Diagnostic Tests
  • Error Messages
• CHAP 5-FORMATTING A HARD DISK
  • Starting the Program
    • Formatting a New Disk
    • Reformatting a Used Disk
    • Selecting an Option
    • Selecting a Drive
  • Option 1, Format
    • Modifying the Defective Truck Table
    • Formatting the Disk
  • Option 2, Destructive Surface Analysis
  • Option 3, Non-destructive Surface Analysis
  • Exiting the Program
• CHAP 6-TROUBLESHOOTING
  • Identifying Your System
  • Error Messages
  • The Computer Won’t Start
  • The Computer Does Not Respond
    • Restoring the Power Supply
  • Password Problems
    • Accessing Your System
  • Keyboard Problems
  • Monitor Problems
  • Diskette Problems
  • Diskette Drive
  • Hard Disk Problems
    • Installing the Drive
    • Preparing the Drive
    • Accessing on the Drive
  • Software Problems
  • Printer Problems
  • Option Card Problems
  • Mouse Problems
  • Memory Module Problems
• APPENDIX A-SPECIFICATIONS
  • CPU and Memory
  • Controllers
  • Mass Storage
  • Keyboard
  • Physical Characteristics
  • Power Supply
  • Environmental Requirements
  • Power Source Requirements
  • System Memory Map
  • Extended VGA Modes
  • Wingine Modes
• GLOSSARY
• INDEX