Document Outline

• Contents
  • Using the Gateway205 Projector 1
    • Safety, Regulatory, and Legal Information 39
      • Using the Gateway205 Projector
• Features
  • Warning
  • Warning
  • Warning
  • Warning
• Projector front
  • Projection lens
• Projector back
  • AC Power connector
• Projector top
• Projector bottom
  • Adjustor-foot
• Cables
  • Important
• Remote control
  • To insert batteries in the remote control:
    • 1 Remove the battery compartment cover.
      • 2 Insert two AAbatteries into the battery compartment. Make sure that the +and– symbols match ...
      • 3 Replace the battery compartment cover.
  • Remote front
  • Remote back
• Setting up the projector
  • To set up the projector:
    • 1 Place the projector on a sturdy cart or table close to other components you plan to connect to ...
      • 2 Point the projector lens towards a blank wall or projection screen.
      • 3 Press the button on the front of the projector to release the adjustor-foot so you can adjust t...
  • Adjustor-foot release button
    • 4 Plug the ACpower cable into the ACpower (ACIN) connector on the back of the projector, then ...
• Connecting components
  • Connecting to your computer
    • To connect the projector to your computer:
      • 1 Plug the VGA cable into the blue PC/HD port on the back of the projector, then plug the other e...
  • Tips & Tricks
    • 2 If you want to use the remote control as a mouse, plug the USB cable into the USB port on the b...
    • Connecting to a DVD player or VCR
      • To connect the projector to a DVD player or VCR using composite video:
        • 1 Plug the yellow composite video cable connector into the Video port on the back of the projecto...
          • 2 Plug the remaining red and white audio connectors from the composite video cable into the corre...
      • To connect the projector to a DVD player or VCR using S-Video:
        • 1 Plug the S-Video cable connector into the S-Video port on the back of the projector, then plug ...
          • 2 Plug the red and white connectors from a composite video cable into the corresponding ports on ...
    • Connecting to a satellite dish
      • To connect the projector to a satellite dish:
        • 1 Plug the component cable connector into the PC/HD port on the back of the projector, then plug ...
          • 2 Plug the red and white connectors from a composite video cable into the corresponding ports on ...
• Operating the projector
  • Starting the projector
    • To start the projector:
      • 1 Press the POWER button. The power LED turns on.
        • 2 Turn on the connected components.
        • 3 Use the lens adjustment wheels to adjust the display image.
  • OSD options
  • Important
    • To adjust the OSD settings:
      • 1 Press the MENU button. The OSD menu opens.
        • 2 Move the joystick up or down to highlight a control, then press the Enterbutton.
        • 3 Move the joystick left or right to adjust the control to the desired level.
        • 4 Press the MENU button to return to the main navigation bar on the left of the OSD menu.
        • 5 When you have finished making all adjustments, press the MENU button to exit the OSD.
    • OSD menus
    • Shutting down the projector
      • To shut down the projector:
        • 1 Turn off all connected components.
          • 2 Press the POWER button on the projector. A warning message appears.
          • 3 Press the POWER button again to turn off the projector.
  • Warning
    • 4 Wait until the fan stops, then disconnect the power cable.
  • Important
• Maintaining the projector
  • Warning
    • Changing the lamp module
  • Warning
    • To replace the lamp module:
      • 1 Turn off the projector and wait for the fan to stop.
        • 2 Disconnect the power cord and all other external cables.
        • 3 Let the projector lamp cool completely (approximately 45minutes).
        • 4 Turn the projector over so the bottom is facing up.
        • 5 Remove the two lamp access panel screws, then remove the lamp access panel.
    • Screws
      • 6 Remove the lamp module retaining screw.
    • Screw
      • 7 Unsnap the lamp removal handle, then lift the lamp module straight up out of the lamp bay.
      • 8 Gently press the new lamp module into the lamp bay. The lamp module is keyed so it can only be ...
      • 9 Replace the lamp module retaining screw.
      • 10 Replace the lamp bay access panel, then replace the access panel screws.
      • 11 Turn the projector over.
      • 12 Connect the power cable and all external cables.
      • To reset the lamp timer:
        • 1 Press the POWER button on the top of the projector twice, a warning message appears.
          • 2 Press the AUTO and BLANK buttons at the same time. A lamp hour icon will appear on the screen.
          • 3 Press the AUTO button to reset the lamp timer.
      • Cleaning the projector
  • Warning
    • Cleaning the exterior
    • Cleaning the projector lens
• Accessories
  • Carrying cases
  • Ceiling mount kits
  • Portable projection screens
  • Replacement lamps
• Troubleshooting
  • Warning
    • First steps
    • Common problems and solutions
      • No power
      • No picture
      • No sound
      • Display image is wider on the top or bottom
      • Display image is poor or blurred
      • Remote control does not work
    • LED status
    • On-screen status messages
      • No signal
      • Out of range
      • Replace the lamp!
• Specifications
  • Display size chart
  • Timing chart
    • Safety, Regulatory, and Legal Information
  • Important safety information
    • Warning
      • Setting up the projector
      • Care during use
      • Replacement parts and accessories
    • Important
  • Regulatory compliance statements
    • United States of America
      • Federal Communications Commission (FCC) Unintentional emitter per FCC Part15
      • FCC declaration of conformity
    • Caution
      • Canada
        • Industry Canada (IC) Unintentional emitter per ICES-003
      • Laser Radiation
    • Warning
      • California Proposition65 Warning
    • Warning
  • Notices
    • All Rights Reserved
    • Trademark Acknowledgments
    • Macrovision statement