Document Outline

• AMTAX sc, AMTAX indoor sc
• Table of Contents
• Section 1 Specifications
• Section 2 General Information
  • 2.1 Safety information
    • 2.1.1 Use of hazard information
    • 2.1.2 Precautionary labels
    • 2.1.3 Change instrument labels
  • 2.2 Product overview
• Section 3 Installation
  • 3.1 Basic installation overview
  • 3.2 Unpack the instrument
  • 3.3 Mechanical installation
    • 3.3.1 Mount the instrument
      • 3.3.1.1 Wall mount
  • 3.4 Initial instrument setup
    • 3.4.1 Open the enclosure
    • 3.4.2 Remove the shipping transport locks
    • 3.4.3 Installation of the collecting tray
    • 3.4.4 Connect the humidity sensor
    • 3.4.5 Determine the appropriate installation option
  • 3.5 Electrical installation
    • 3.5.1 Electrostatic Discharge (ESD) Considerations
    • 3.5.2 Enclosure breakouts
    • 3.5.3 Insert tubing and/or cables
    • 3.5.4 Connect the Filter Probe to the analyzer
    • 3.5.5 Connect the optional heated drain
  • 3.6 Installation of reagents
  • 3.7 Gas-sensitive electrode
    • 3.7.1 Installation of the electrode and electrolyte
      • 3.7.1.1 Fill the electrode with electrolyte
  • 3.8 Supply power to the analyzer
  • 3.9 Connect the data network
• Section 4 System Start Up
  • 4.1 Initializing the instrument
• Section 5 Operation
  • 5.1 Sensor diagnostics menu
  • 5.2 Sensor setup menu
    • 5.2.1 System setup menu
  • 5.3 Calibration process
  • 5.4 Cleaning process
  • 5.5 Measurement process
• Section 6 Maintenance
  • 6.1 General maintenance
    • 6.1.1 Clean the analyzer
      • 6.1.1.1 Cleaning interval
    • 6.1.2 Replace the fan filter
    • 6.1.3 Fuse replacement
  • 6.2 Reagent replacement
  • 6.3 Routine maintenance schedule
  • 6.4 Scheduled maintenance
  • 6.5 Replace the membrane cap, electrolyte and electrode
  • 6.6 Validation (Analytical quality assurance)
  • 6.7 Shut the analyzer down
    • 6.7.1 Shut the analyzer down for an extended period
  • 6.8 Modify from single channel to dual channel
• Section 7 Troubleshooting
  • 7.1 Troubleshooting the controller
  • 7.2 Troubleshooting the analyzer
    • 7.2.1 LED status
    • 7.2.2 Error messages
    • 7.2.3 Warnings
  • 7.3 Troubleshooting the Electrode
• Section 8 Replacement Parts and Accessorie
  • 8.1 Standards and reagents
  • 8.2 Analyzer accessories
  • 8.3 Mounting hardware and accessories
  • 8.4 Replacement parts
• Section 9 Contact Information
• Section 10 Warranty and liability
• Appendix A Plumbing and Connection Options
  • A.1 Safety information
    • A.1.1 Electrostatic Discharge (ESD) Considerations
  • A.2 Connect a 2-parameter option
    • A.2.1 Remove the T-fitting
  • A.3 Drain line considerations
  • A.4 Tubing considerations
  • A.5 Option 1 plumbing and connections
  • A.6 Option 2 plumbing and cable connections
  • A.7 Option 3 plumbing and connections
  • A.8 Option 4 plumbing and connections
  • A.9 Option 5 plumbing and connections
  • A.10 Option 6 plumbing and connections
  • A.11 Option 7 plumbing and connections
  • A.12 Option 8a plumbing and connections
  • A.13 Option 8b plumbing and connections
  • A.14 Option 9a plumbing and connections
  • A.15 Option 9b plumbing and connections
  • A.16 Option 10a plumbing and connections
  • A.17 Option 10b plumbing and connections
  • A.18 Option 11a plumbing and connections
  • A.19 Option 11b plumbing and connections
• Appendix B Fieldbus Communications
  • B.1 Fieldbus control
  • B.2 Remote controlled measurement series
  • B.3 External trigger contact, Control by external signal
  • B.4 Modbus register information