Document Outline

• Table of Contents
• Section 1 Specifications
  • 1.1 Dimensions
  • 1.2 Bottle and retainer configurations
• Section 2 General Information
  • 2.1 Safety information
    • 2.1.1 Use of hazard information
    • 2.1.2 Precautionary labels
    • 2.1.3 Confined space precautions
  • 2.2 Sampler overview
    • 2.2.1 Sampler components
• Section 3 Installation
  • 3.1 Unpack the sampler
  • 3.2 Installation guidelines
    • 3.2.1 Manhole installation
  • 3.3 Sampler base preparation
    • 3.3.1 Clean the sample bottles
    • 3.3.2 Single bottle installation
      • 3.3.2.1 Full bottle shut-off installation
    • 3.3.3 Multiple bottle installation
      • 3.3.3.1 Bottle number 1 position
      • 3.3.3.2 Two or four bottle installation
      • 3.3.3.3 Eight bottle installation
      • 3.3.3.4 24 bottle installation
      • 3.3.3.5 Distributor installation
  • 3.4 Intake tubing and strainer installation
  • 3.5 Electrical installation
    • 3.5.1 Power installation
      • 3.5.1.1 Battery installation
      • 3.5.1.2 AC power installation
    • 3.5.2 Flow meter installation
    • 3.5.3 Communications installation
• Section 4 Sampler operation
  • 4.1 Power on and power off
  • 4.2 Controller overview
    • 4.2.1 Keypad description
    • 4.2.2 Navigation
    • 4.2.3 Parameter selection
  • 4.3 Main menu overview
  • 4.4 Sampler programs
    • 4.4.1 Sampler program overview
    • 4.4.2 Create a sampler program
      • 4.4.2.1 Tips and techniques
    • 4.4.3 Modify a program
    • 4.4.4 Review a program
    • 4.4.5 Restore default settings
    • 4.4.6 Store programs as presets
      • 4.4.6.1 Load a stored program
  • 4.5 Start or stop a program
  • 4.6 Manual operation
    • 4.6.1 Collect grab samples
    • 4.6.2 Move the distributor arm
    • 4.6.3 Start or stop the pump
  • 4.7 View data
    • 4.7.1 Status screen
    • 4.7.2 Status for main program
      • 4.7.2.1 Ready to start
      • 4.7.2.2 Running/halted
      • 4.7.2.3 Complete
    • 4.7.3 Status for stormwater program
    • 4.7.4 Sample history
    • 4.7.5 Event log
      • 4.7.5.1 View the event log
      • 4.7.5.2 Erase the event log
  • 4.8 Volume calibration
    • 4.8.1 Volume calibration using the liquid sensor
      • 4.8.1.1 Reset the calibration
    • 4.8.2 Volume calibration based on time
    • 4.8.3 Verify sample volume
  • 4.9 Controller settings
    • 4.9.1 Liquid sensor calibration
    • 4.9.2 Set password
    • 4.9.3 Tubing life indicator
      • 4.9.3.1 Enable the tubing life indicator
      • 4.9.3.2 Tubing life status
      • 4.9.3.3 Tubing life cycle limit
      • 4.9.3.4 Reset tubing cycles
• Section 5 Advanced sampling
  • 5.1 Advanced sampling overview
  • 5.2 Advanced sampling menu
  • 5.3 Advanced sampling instructions
    • 5.3.1 Send output signal at program completion
    • 5.3.2 Send output signal with sample cycle (special output)
    • 5.3.3 Operate from external signal (setpoint sample)
    • 5.3.4 Set multiple start and stop times
    • 5.3.5 Collect first flush stormwater samples
    • 5.3.6 Set variable intervals
• Section 6 Maintenance
  • 6.1 Upgrades, Repairs, General Maintenance
  • 6.2 Sampler cleaning
  • 6.3 Pump maintenance
    • 6.3.1 Pump tube life
    • 6.3.2 Pump tube replacement
    • 6.3.3 Rotor removal and cleaning
  • 6.4 Distributor arm tubing replacement
  • 6.5 Desiccant replacement
• Section 7 Troubleshooting
  • 7.1 General troubleshooting
  • 7.2 Error messages and notifications
  • 7.3 Diagnostic tests
    • 7.3.1 Distributor diagnostic
    • 7.3.2 Keypad diagnostic
    • 7.3.3 LCD diagnostic
    • 7.3.4 Liquid sensor diagnostic
• Section 8 Replacement Parts and Accessories
  • 8.1 Bottle kits
  • 8.2 Containers and bottle sets
  • 8.3 Replacement parts
  • 8.4 Accessories
• Section 9 Contact information
• Appendix A Wiring for non-Sigma flow meters
• Index