Document Outline

• Section One - Introduction
  • Table of Contents
  • Steps for Successfully Programming the Aurora 9X
  • What’s New?
  • Aurora Transmitter Accessories
  • Product Support
  • System Component Specifications
  • Glossary of Terms
  • Icon Identification
  • Safety Information
  • Aurora 9X Transmitter Warnings
  • Transmitter Battery Information
  • Hitec 2.4GHz System
    • Maxima Series Receiver Features
    • Optima and Minima Series Receiver Features
    • Maxima Series Receiver Link (ID-Setting)
    • Optima and Minima Series Receiver Link (ID-Setting or Bind)
    • FAIL-SAFE and Hold Mode Setup
    • Telemetry System
    • Range Check Function
    • Scan Mode
    • SLT Technology
  • Aurora 9X Transmitter Controls
  • Touch Screen Lock
  • The First Screen
    • The Multi-I/O port
  • Home Screen Menu
• Section Two - Quick Start Guide to Set up a Simple Powered Airplane or Glider
  • System Programming Menu
  • Model Programming Menu
• Section Three - Quick Start Guide to Setting Up a Simple Heli
  • System Programming Menu
  • Model Programming Menu
• Section Four - System Menu
  • Model Select Menu
    • Create a new model
    • Select an existing model
    • Copy one model’s data into a new model memory slot
    • Rename a model
  • Model Type Menu
  • Timer Menu
  • Channel Menu
  • Trimstep
  • Sensor Menu
  • Trainer Menu
  • Spectra Control Menu
  • System Management Menu
  • Mode Menu
  • Hardware Reverse Menu
  • Information Menu
• Section Five Model Menu and More Special Hints
  • Special Hints
    • Additional Menus, the Custom and Adjust Features
    • Adjustment Menu
  • Model Menu and More - The Switch Selection Process
    • Selecting a Switch
    • Adjust Function switch set-up
    • Additional camber and launch mode adjust function menu (GLID)
    • Helicopter throttle and pitch curve adjust functions, hover trim and more
    • Trim Link Activation
    • Cut Position set-up
    • Launch Cut switch set-up
  • Model Menu and More - Menu Functions Common to all ACRO, GLID and HELI models.
    • EPA (End Point Adjustment)
    • D/R & EXP (Dual Rates and Exponential Rates)
    • Sub-Trim (Servo Sub-Trim Adjustment)
    • Reverse (Servo Travel Direction Reverse)
    • S. Speed (Servo Speed Adjustmemt)
    • Monitor (Control Movement Monitor)
    • T.Limit (Travel Limit)
    • P. Mixes (Programmable Mix Menu)
    • Gyro (on/off and Sensitivity Adjustment)
• Section Six - Model Menu-Common Model Functions to ACRO and GLID
  • FLT.COND (ACRO)
  • FLT.COND (GLID)
  • FLT.COND (ACRO and GLID)
  • Spoiler (GLID)
  • SPO-ELE (GLID)
  • AIL-RUD (ACRO and GLID)
  • ELE-CAM (ACRO and GLID)
  • RUD-AIL (ACRO and GLID)
  • AIL DIFF (ACRO and GLID)
  • AIL- FLP (ACRO and GLID)
  • CAMBMIX (ACRO and GLID)
  • FLP CON (ACRO and GLID)
  • FLAPTRIM (ACRO)
  • V.Tail (ACRO and GLID)
  • AILEVATOR (ACRO and GLID)
  • Elevon (ACRO and GLID)
  • Thro.Cut (ACRO)
  • T.Curve (ACRO)
  • Idle Down (ACRO )
  • B-fly (GLID)
  • SnapRoll (ACRO)
  • Knife Edge Mix(ARCO)
  • Motor (GLID)
  • Launch (GLID)
  • Offset (GLID)
• Section Seven - Model Menu - HELI Specific Functions
  • FLT.COND (HELI)
  • Pitch and Throttle Curves (HELI)
  • Needle (HELI)
  • SWH-THR (HELI)
  • RUD-THR (HELI)
  • T. HOLD (HELI)
  • Swash Mix (HELI)
  • REVO Mix (HELI)
  • Gyro (HELI)
  • Governor (HELI)