Document Outline

• 326RJX
• Operator’s manual (EPA)
• Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
• Symbols
• WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others.
• Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
• Always wear:
• . A protective helmet where there is a risk of falling objects
• . Hearing protection
• . Approved eye protection
• Max. speed of output shaft, rpm
• Watch out for thrown objects and ricochets.
• The operator of the machine must ensure, while working, that no persons or animals come closer than 15 metres.
• Machines fitted with saw blades or grass blades can be thrown violently to the side when the blade comes into contact with a fix...
• Arrows which show limits for handle positioning.
• Always wear approved protective gloves.
• Wear sturdy, non-slip boots.
• Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord.
• Only intended for trimmer heads.
• Other symbols/decals on the machine refer to special certification requirements for certain markets.
• Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance.
• Always wear approved protective gloves.
• Regular cleaning is required.
• Visual check.
• Approved eye protection must always be used.
• Contents
• KEY TO SYMBOLS
• Symbols
• 2
• CONTENTS
• Contents
• 3
• Note the following before starting:
• 3
• SAFETY INSTRUCTIONS
• Personal protective equipment
• 4
• Machine¢s safety equipment
• 4
• Checking, maintaining and servicing the machine¢s safety equipment
• 6
• Cutting equipment
• 8
• General safety precautions
• 9
• General working instructions
• 10
• Basic working techniques
• 10
• WHAT IS WHAT?
• What is what on the trimmer?
• 12
• ASSEMBLY
• Fitting the J-handle
• 13
• Fitting blades and trimmer heads
• 13
• Fitting a trimmer guard and Superauto II trimmer head
• 13
• Fitting the blade guard/combination guard, grass blade and grass cutter
• 14
• Fitting other guards and cutting attachments
• 14
• FUEL HANDLING
• Fuel
• 15
• Fuelling
• 15
• STARTING AND STOPPING
• Check before starting
• 16
• Starting and stopping
• 16
• MAINTENANCE
• Carburettor
• 18
• Muffler
• 19
• Cooling system
• 20
• Spark plug
• 20
• Air filter
• 20
• Bevel gear
• 21
• Maintenance schedule
• 21
• TECHNICAL DATA
• Technical data
• 22
• FEDERAL EMISSION CONTROL WARRANTY STATEMENT
• YOUR WARRANTY RIGHTS AND OBLIGATIONS
• 23
• Note the following before starting:
• Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice.
• Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection.
• Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual.
• WARNING! Under no circumstances may the design of the machine be modified without the permission of the manufacturer. Always use...
• Your warranty may not cover damage or liability caused by the use of non-authorized accessories or replacement parts.
• WARNING! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fat...
• The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours.
• For customer assistance call: 704-921-7000 or contact us at our website: www.husqvarna.com
• Personal protective equipment
• IMPORTANT! Whenever you use a clearing saw, brushcutter or trimmer you must wear personal protective equipment that is approved ...
• WARNING! Listen out for warning signals or shouts when you are wearing hearing protection. Always remove your hearing protection as soon as the engine stops.
• GLOVES
• Gloves should be worn when necessary, e.g., when fitting cutting attachments.
• HEARING PROTECTION
• Wear hearing protection that provides adequate noise reduction.
• EYE PROTECTION
• Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved protective goggles must comply with standard ANSI Z87.1 in the USA or EN 166 in EU countries. Visors must comply with standard EN 1731.
• BOOTS
• Wear sturdy, non-slip boots.
• CLOTHING
• Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level.
• FIRST AID KIT
• Always have a first aid kit nearby.
• Machine¢s safety equipment
• This section describes the machine¢s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine.
• The life span of the machine can be reduced and the risk of accidents can increase if machine maintenance is not carried out cor...
• WARNING! Never use a machine that has faulty safety equipment! Carry out the inspection, maintenance and service routines listed in this section.
• Throttle lock
• The throttle lock is designed to prevent accidental operation of the throttle control. When you press the lock (A) (i.e. when yo...
• Stop switch
• Use the stop switch to switch off the engine.
• Cutting attachment guard
• This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment.
• WARNING! Never use a cutting attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury.
• Vibration damping system
• Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier.
• Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration.
• The machine¢s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine¢s handle unit.
• WARNING! Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation. Conta...
• Muffler
• The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user. A muffler fitted with a catalytic converter is also designed to reduce harmful exhaust gases.
• In countries that have a warm and dry climate there is a significant risk of fire. We therefore fit certain mufflers with a spark arrestor mesh. Check whether the muffler on your machine is fitted with this kind of mesh.
• For mufflers it is very important that you follow the instructions on checking, maintaining and servicing your machine. See instructions under the heading Checking, maintaining and servicing the machine’s safety equipment.
• WARNING! Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of fire!
• WARNING! The inside of the muffler contain chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged muffler.
• WARNING! Bear in mind that:
• Engine exhaust fumes contain carbon monoxide, which can cause carbon monoxide poisoning. For this reason you should not start or run the machine indoors, or anywhere that is poorly ventilated.
• The exhaust fumes from the engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near combustible material!
• Cutting equipment
• Grass blades and grass cutters are intended for cutting coarse grass.
• A trimmer head is intended for trimming grass.
• Locking nut
• A locking nut is used to secure some types of cutting attachment.
• Checking, maintaining and servicing the machine¢s safety equipment
• IMPORTANT! All servicing and repair work on the machine requires special training. This is especially true of the machine¢s safe...
• Throttle lock
• . Make sure the throttle control is locked at the idle setting when the throttle lock is released.
• . Press the throttle lock and make sure it returns to its original position when you release it.
• . Check that the throttle control and throttle lock move freely and that the return springs work properly.
• . See instructions under the heading Start. Start the machine and apply full throttle. Release the throttle and check that the c...
• Stop switch
• . Start the engine and make sure the engine stops when you move the stop switch to the stop setting.
• Cutting attachment guard
• . Ensure that the guard is undamaged and is not cracked.
• . Replace the guard if it has been exposed to impact or is cracked.
• . Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.
• Vibration damping system
• . Regularly check the vibration damping units for cracks or deformation.
• . Check that the vibration damping element is undamaged and securely attached.
• Muffler
• . Never use a machine that has a faulty muffler.
• . Regularly check that the muffler is securely attached to the machine.
• . If the muffler on your machine is fitted with a spark arrestor mesh then it should be cleaned regularly. A blocked mesh causes the engine to overheat, which can lead to serious damage. Never use a muffler with a defective spark arrestor mesh.
• Cutting equipment
• This section describes how to choose and maintain your cutting equipment in order to:
• . Reduce the risk of kickback.
• . Obtain maximum cutting performance.
• . Extend the life of cutting equipment.
• General rules
• 1 Only use cutting attachments with the guards we recommend! See the chapter on Technical data.
• 2 Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended file gauge. An incorrectly sharpened or damaged blade increases the risk of accidents.
• 3 Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced.
• Locking nut
• . When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-hand thread.)
• . Tighten the nut using the socket spanner. 35-50 Nm (3.5- 5 kpm).
• CAUTION! The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times.
• WARNING! Never use a machine with faulty safety equipment. The machine’s safety equipment must be checked and maintained as described in this section. If your machine fails any of these checks contact your service agent to get it repaired.
• Cutting equipment
• IMPORTANT!
• This section describes how to choose and maintain your cutting equipment in order to:
• Reduce the risk of kickback.
• Obtain maximum cutting performance.
• Extend the life of cutting equipment.
• Only use cutting attachments with the guards we recommend! See the chapter on Technical data.
• Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter.
• Keep the teeth of the blade correctly sharpened! Follow our recommendations. Also refer to the instructions on the blade packaging.
• WARNING! Using an incorrect cutting attachment or an incorrectly sharpened blade increases the risk of kickback.
• Sharpening grass cutters and grass blades
• . See the cutting attachment packaging for correct sharpening instructions.
• . Sharpen blades and cutters using a single-cut flat file.
• . Sharpen all edges equally to maintain the balance of the blade.
• Trimmer head
• . Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engi...
• . Smaller machines generally require small trimmer heads and vice versa. This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared.
• . The length of the cord is also important. A longer cord requires greater engine power than a shorter cord of the same diameter.
• . Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length.
• . To increase the life of the cord it can be soaked in water for a couple of days. This will make the line tougher so that it lasts longer.
• IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration.
• WARNING! Always stop the engine before doing any work on the cutting attachment. This continues to rotate even after the throttl...
• General safety precautions
• IMPORTANT!
• The machine is only designed for trimming grass, grass clearing and/or forestry clearing.
• The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data.
• Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.
• Never use the machine in extreme weather conditions such as severe cold, very hot and/or humid climates.
• Wear personal protective equipment. See instructions under the heading Personal protective equipment.
• Never use a machine that has been modified in any way from its original specification.
• Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some ma...
• All covers and guards must be fitted before starting. Make sure the spark plug cap and HT lead are not damaged. Otherwise you could get an electric shock.
• The machine operator must ensure that no people or animals come closer than 15 metres while working. When several operators are working in the same area the safety distance should be at least twice the tree height and no less than 15 metres.
• WARNING! Using an incorrect cutting attachment or an incorrectly filed blade can increase the risk of accidents.
• Starting
• WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately.
• . The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.
• . Never start the machine indoors. Exhaust fumes can be dangerous if inhaled.
• . Observe your surroundings and make sure that there is no risk of people or animals coming into contact with the cutting equipment.
• . Place the machine on the ground, ensure the cutting attachment is clear of twigs and stones. Hold the body of the machine on t...
• Fuel safety
• . Always use a fuel container with an anti-spill valve.
• . Never refuel the machine while the engine is running. Always stop the engine and let it cool for a few minutes before refuelling.
• . Make sure there is plenty of ventilation when refuelling or mixing fuel (gasoline and 2-stroke oil).
• . Move the machine at least 3 m from the refuelling point before starting it.
• . Never start the machine:
• 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate.
• 2 If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.
• 3 If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.
• 4 Avoid all skin contact with fuel. Fuel is a skin irritant and may even cause skin changes.
• Transport and storage
• . Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames, for example, from electrical machinery, electric motors, electrical relays/switches or boilers.
• . When storing and transporting fuel always use approved containers intended for this purpose.
• . When storing the machine for long periods the fuel tank must be emptied. Contact your local gas station to find out where to dispose of excess fuel.
• . The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage.
• WARNING! Take care when handling fuel. Bear in mind the risk of fire, explosion and inhaling fumes.
• General working instructions
• IMPORTANT!
• This section describes the basic safety precautions for working with clearing saws and trimmers.
• If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.
• Avoid all usage which you consider to be beyond your capability.
• You must understand the difference between forestry clearing, grass clearing and grass trimming before use.
• Basic safety rules
• 1 Look around you:
• . To ensure that people, animals or other things cannot affect your control of the machine.
• . To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting attachment.
• . CAUTION! Do not use the machine unless you are able to call for help in the event of an accident.
• 2 Do not use the machine in bad weather, such as dense fog, heavy rain, strong wind, intense cold, etc. Working in bad weather is tiring and can lead to dangerous conditions, e.g. slippery surfaces.
• 3 Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take great care when working on sloping ground.
• 4 Switch off the engine before moving to another area. Fit the transport guard before carrying or transporting the equipment any distance.
• 5 Never put the machine down with the engine running unless you have it in clear sight.
• Basic working techniques
• . Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage.
• Terms
• . Use a grass cutter or grass blade for clearing grass.
• . Use a trimmer head or plastic blades for lighter clearing work, for example along verges or around trees.
• WARNING! Sometimes branches or grass get caught between the guard and cutting attachment. Always stop the engine before cleaning.
• Grass clearing using a grass blade
• . A grass blade is used for all types of tall or coarse grass.
• . The grass is cut down with a sideways, swinging movement, where the movement from right-to-left is the clearing stroke and the...
• . If the blade is angled to the left when clearing grass, the grass will collect in a line, which makes it easier to collect, e.g. by raking.
• . Try to work rhythmically. Stand firmly with your feet apart. Move forward after the return stroke and stand firmly again.
• . Let the support cup rest lightly against the ground. It is used to protect the blade from hitting the ground.
• . Reduce the risk of material wrapping around the blade by following these instructions:
• 1 Always work at full throttle.
• 2 Avoid the previously cut material during the return stroke.
• . Stop the engine, unclip the harness and place the machine on the ground before you start to collect the cut material.
• Grass trimming using a trimmer head and plastic blades
• Trimming
• . Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Never press the cord into the area to be cut.
• . The cord can easily remove grass and weeds up against walls, fences, trees and borders, however it can also damage sensitive bark on trees and bushes, and damage fence posts.
• . Reduce the risk of damaging plants by shortening the cord to 10-12 cm and reducing the engine speed.
• Clearing
• . The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end o...
• . The cord wears quicker and must be fed forward more often when working against stones, brick, concrete, metal fences, etc., than when coming into contact with trees and wooden fences.
• . When trimming and clearing you should use less than full throttle so that the cord lasts longer and to reduce the wear on the trimmer head.
• Cutting
• . The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.
• . Do not allow the trimmer head to constantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head.
• Sweeping
• . The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and above the area to be swept and move the tool to and fro.
• . When cutting and sweeping you should use full throttle to obtain the best results.
• WARNING! Neither the operator of the machine nor anyone else may attempt to remove the cut material while the engine is running or the blade is rotating, as this can result in serious injury.
• Stop the engine and blade before you remove material that has wound around the blade shaft as otherwise there is a risk of injury. The bevel gear can get hot during use and may remain so for a while afterwards. You could get burnt if you touch it.
• WARNING! Watch out for thrown objects. Always wear eye protection. Never lean over the cutting attachment guard. Stones, rubbish, etc. can be thrown up into the eyes causing blindness or serious injury.
• Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be kept outside the safety zone of 15 m. Stop the machine immediately if anyone approaches.
• What is what on the trimmer?
• 1 Trimmer head
• 2 Grease filler cap
• 3 Bevel gear
• 4 Cutting attachment guard
• 5 Shaft
• 6 Loop handle
• 7 Throttle control
• 8 Stop switch
• 9 Throttle lock
• 10 Cylinder cover
• 11 Starter handle
• 12 Fuel tank
• 13 Choke control
• 14 Air purge
• 15 Air filter cover
• 16 Handle adjustment
• 17 Locking nut
• 18 Support flange
• 19 Drive disc
• 20 Socket spanner
• 21 Operator’s manual (EPA)
• 22 Allen key
• 23 Locking pin
• 24 Support cup
• 25 Blade
• 26 Transport guard
• 27 J-handle
• 28 Support eyes for harness
• 29 Harness
• Fitting the J-handle
• . Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft.
• . Slide the spacer into the slot in the loop handle.
• . Fit the nut, knob and screw. Do not overtighten.
• . Attach the J-handle to the loop handle using the three screws, as shown.
• . Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob.
• WARNING! Only grass blades/grass cutters or trimmer heads/plastic blades may be used when the J-handle is fitted. Saw blades must never be used with the J-handle.
• Fitting blades and trimmer heads
• When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages c...
• WARNING! Never use a cutting attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury.
• Fitting a trimmer guard and Superauto II trimmer head
• . Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L).
• . Fit the drive disc (B) on the output shaft.
• . Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.
• . Insert the locking pin (C) in the hole to lock the shaft.
• . To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows:
• . Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger...
• . Place the cover (I) and the support flange (F) on the output shaft.
• . Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold t...
• . Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.
• . To dismantle, follow the instructions in the reverse order.
• Fitting the blade guard/combination guard, grass blade and grass cutter
• . Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CAUTION! Use the recommended blade guard. See the Technical data section.
• . Fit the drive disc (B) on the output shaft.
• . Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.
• . Insert the locking pin (C) in the hole to lock the shaft.
• . Place the blade (D), support cup (E) and support flange (F) on the output shaft.
• . Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold t...
• Fitting other guards and cutting attachments
• . Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L).
• . Fit the drive disc (B) on the output shaft.
• . Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.
• . Insert the locking pin (C) in the hole to lock the shaft.
• . Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.
• . To dismantle, follow the instructions in the reverse order.
• Fuel
• CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke en...
• WARNING! Always ensure there is adequate ventilation when handling fuel.
• Gasoline
• CAUTION! Always use high grade unleaded oil mixed gasoline (minimum 87 RON). If your machine is equipped with a catalytic conver...
• Use low-emission gasoline, also known as alkylate gasoline, if it is available.
• . This engine is certified to operate on unleaded gasoline.
• . The lowest recommended octane rating is 87. If you run the engine on lower octane rating than 87 so-called “knocking“ can occur. This leads to an increased engine temperature, which can result in a serious engine breakdown.
• . When working at continuous high revs a higher octane rating is recommended.
• Two-stroke oil
• . For best results and performance use HUSQVARNA two- stroke oil, which is specially formulated for our two-stroke engines. Mixture 1:50 (2%).
• . Never use two-stroke oil intended for water-cooled outboard engines, sometimes referred to as outboard oil.
• . Never use oil intended for four-stroke engines.
• Gasoline, litre
• Two-stroke oil, litre
• 2% (1:50)
• 5
• 0,10
• 10
• 0,20
• 15
• 0,30
• 20
• 0,40
• US gallon
• US fl. oz.
• 1
• 2 1/2
• 2 1/2
• 6 1/2
• 5
• 12 7/8
• Mixing
• . Always mix the gasoline and oil in a clean container intended for fuel.
• . Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.
• . Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.
• . Do not mix more than one month’s supply of fuel at a time.
• . If the machine is not used for some time the fuel tank should be emptied and cleaned.
• . This engine is certified to operate on unleaded gasoline.
• WARNING! The catalytic converter muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when working near flammable substances and/or vapours.
• Fuelling
• WARNING! Taking the following precautions, will lessen the risk of fire:
• Do not smoke or place hot objects near fuel.
• Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling.
• When refuelling, open the fuel cap slowly so that any excess pressure is released gently. Tighten the fuel cap carefully after refuelling. Always move the machine away from the refuelling area before starting.
• . Clean the area around the fuel cap. Contamination in the tank can cause operating problems.
• . Ensure that the fuel is well mixed by shaking the container before filling the tank.
• Check before starting
• For safety reasons follow these recommendations!
• . Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason ...
• . Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked.
• . Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.
• . Check that the blade guard is not damaged or cracked. Replace the blade guard if it is exposed to impact or is cracked.
• . Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked.
• . Never use the machine without a guard nor with a defective guard.
• Starting and stopping
• WARNING! The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.
• Always move the machine away from the refuelling area before starting. Place the machine on a flat surface. Ensure the cutting attachment cannot come into contact with any object.
• Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres.
• Cold engine
• Ignition: Set the stop switch to the start position.
• Choke: Set the choke control in the choke position.
• Air purge: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.
• Warm engine
• Ignition: Set the stop switch to the start position.
• Choke: Set the throttle to the start position by moving the choke control to the choke position and then returning it to its original position.
• Air purge: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.
• Stopping
• Stop the engine by switching off the ignition.
• WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately.
• Starting
• Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly ...
• Repeat pulling the cord until the engine starts. When the engine starts. return choke control to run position and apply full throttle; the throttle will automatically disengage from the start setting.
• CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.
• Carburettor
• Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has ...
• WARNING! The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.
• Function
• . The carburettor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburettor. The air/fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine.
• . The setting of the carburetor means that the engine is adepted to local conditions, for example, the climate, altitude, fuel and the type of 2-stroke oil.
• . The carburettor has three adjustment controls:
• L = Low speed jet
• H = High speed jet
• T = Idle adjustment screw
• . The L and H-jets are used to adjust the supply of fuel to match the rate that air is admitted, which is controlled with the th...
• . The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.
• Basic setting
• . The basic carburettor settings are adjusted during testing at the factory. The basic setting is richer than the optimal settin...
• CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops.
• Rec. idle speed 2700 rpm
• Recommended max. speed: See the Technical data section.
• WARNING! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.
• Fine adjustment
• . When the machine has been ”run-in” the carburettor should be finely adjusted. The fine adjustment should be carried out by a qualified person. First adjust the L- jet, then the idling screw T and then the H-jet.
• Conditions
• . Before any adjustments are made, make sure that the air filter is clean and the air filter cover is fitted. If you adjust the ...
• . Carefully turn both jets, L and H, so that they are midway between fully screwed in and fully screwed out.
• . Do not attempt to adjust the L and H jets beyond either stop as this could cause damage.
• . Now start the machine according to the starting instructions and let it warm up for 10 minutes.
• CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops.
• Low speed jet L
• Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/ 4 turn counter-clockwise.
• CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops.
• Fine adjustment of the idle speed T
• Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T ...
• IMPORTANT! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.
• High speed jet H
• The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean ...
• Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed je...
• Note that the engine should not be under load when you adjust the high speed jet H. You should therefore remove the cutting attachment, nut, support flange and drive disc before adjusting the high speed jet H.
• The high speed jet H is adjusted correctly when the machine burbles a little. If the machine races then the setting is too lean. If the engine produces a lot of smoke and burbles a lot then the setting is too rich.
• CAUTION! For optimum adjustment of the carburettor, contact a qualified dealer/service workshop that has a revolution counter at their disposal.
• Correctly adjusted carburettor
• When the carburettor is correctly adjusted the machine will accelerate without hesitation and burble a little at maximum speed. ...
• If the high speed jet H is set too lean it will result in less power, less performance, poor acceleration and/or damage to the engine.
• If both the L and H jets are set too rich it will results in acceleration problems or too low a working speed.
• Muffler
• CAUTION! Some mufflers are fitted with a catalytic converter. See chapter on Technical data to see whether your machine is fitted with a catalytic converter.
• The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.
• Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. This is best done with a wire brush.
• On mufflers without a catalytic converter the mesh should be cleaned weekly, or replaced if necessary. On mufflers fitted with a...
• If the mesh is frequently blocked, this can be a sign that the performance of the catalytic converter is impaired. Contact your ...
• CAUTION! Never use a machine with a defective muffler.
• WARNING! Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember the risk of fire!
• Cooling system
• To keep the working temperature as low as possible the machine is equipped with a cooling system.
• The cooling system consists of:
• 1 Air intake on the starter.
• 2 Fins on the flywheel.
• 3 Cooling fins on the cylinder.
• 4 Cylinder cover (directs cold air over the cylinder).
• Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.
• Spark plug
• The spark plug condition is influenced by:
• . Incorrect carburettor adjustment.
• . An incorrect fuel mixture (too much or incorrect type of oil).
• . A dirty air filter.
• These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.
• If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking...
• CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder.
• Air filter
• The air filter must be regularly cleaned to remove dust and dirt in order to avoid:
• . Carburettor malfunctions
• . Starting problems
• . Loss of engine power
• . Unnecessary wear to engine parts
• . Excessive fuel consumption.
• Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty.
• Cleaning the air filter
• Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Ensure that the filter is dry before refitting it.
• An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.
• If the machine is used in dusty conditions the air filter should be soaked in oil. See instructions under the heading Oiling the air filter.
• Oiling the air filter
• Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.
• Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess...
• Bevel gear
• The bevel gear is filled with the right quantity of grease at the factory. However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease.
• The grease in the bevel gear does not normally need to be changed except if repairs are carried out.
• CAUTION! Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury ...
• Maintenance schedule
• Below you will find some general maintenance instructions. If you need further information please contact your service workshop.
• Daily maintenance
• . Check throttle trigger and throttle trigger lockout function.
• . Check that the stop switch works correctly.
• . Check that the blades do not move when the engine is idling.
• . Clean the outside of the machine.
• . Check that the harness is not damaged.
• . Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked.
• . Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked.
• . A non-balanced blade/trimmer head induces heavy vibrations that may damage the machine.
• . Check that the blade nut is sufficiently tightened.
• . Check that nuts and screws are tight.
• . Check that the screws that hold the bevel gear are tight.
• . Check that there are no fuel leaks from the engine, tank or fuel lines.
• Weekly maintenance
• . Check the starter and starter cord.
• . Clean the carburettor area.
• . Clean the outside of the spark plug. Remove it and check the electrode gap. Adjust the gap to 0.5 mm (.20”), or replace the spark plug. Check that the spark plug is fitted with a suppressor.
• . Clean the cooling fins on the cylinder and check that the air intake near the starter is not blocked.
• . Check that the bevel gear is filled with grease up to 3/4. Use special grease.
• . Clean the air filter.
• Monthly maintenance
• . Clean the fuel tank.
• . Clean the outside of the carburettor and the space around it.
• . Clean the fan and the area around it.
• . Check fuel hose for cracks or other damage. Change if necessary.
• . Change the fuel filter in fuel tank.
• . Check the clutch, clutch springs and the clutch drum for wear. Replace if necessary.
• . Check electrical wires and connections.
• . Replace the spark plug. Check that the spark plug is fitted with a suppressor.
• . Change the air filter.
• . Check and clean the spark arrestor mesh on the muffler (only applies to mufflers fitted with a catalytic converter).
• Technical data
• 325RJ-X
• Engine
• Cylinder volume, cu.in/cm3
• 1,50/24,5
• Cylinder bore, inch/mm
• 1,34/34,0
• Stroke, inch/mm
• 1,06/27
• Idle speed, rpm
• 2700
• Recommended max. speed, rpm
• 11000-11700
• Speed of output shaft, rpm
• 8014
• Max. engine output, acc. to ISO 8893
• 0,9/9000
• Catalytic converter muffler
• Yes
• Speed-regulated ignition system
• Yes
• Ignition system
• Manufacturer/type of ignition system
• WalbroMB/SEM AM49
• Spark plug
• Champion RCJ 7Y
• Electrode gap, inch/mm
• 0,02/0,5
• Fuel and lubrication system
• Manufacturer/type of carburettor
• Zama C1Q
• Fuel tank capacity, US pint/litre
• 1,06/0,5
• Weight
• Weight without fuel, cutting attachment and guard, Lbs/kg
• 9,5/4,3
• Sound levels
• (see note 1)
• Equivalent sound pressure level at the user¢s ear, measured according to ANSI B175.3-1997, dB(A), min/ max:
• 92/98
• Vibration levels
• Vibration levels at handles, measured according to ANSI B175.3-1997, m/s2
• At idle, left/right handles, min.:
• 1,5/1,4
• At idle, left/right handles, max.:
• 2,0/1,8
• At max. speed, left/right handles, min.:
• 2,5/4,8
• At max. speed, left/right handles, max.:
• 4,9/8,0
• NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values.
• Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.
• Approved accessories
• Type
• Cutting attachment guard, Art. no.
• Arbor shaft thread M10
• Plastic blades
• Tricut Ø 300 mm
• 503 93 42-02
• Grass blade/grass cutter
• Grass 255-4 1" (Ø 255 4-teeth)
• 503 93 42-02
• Grass 255-8 1" (Ø 250 8-teeth)
• 503 93 42-02
• Trimmer head
• Trimmy H II 1"
• 503 97 71-01 / 503 93 42-02
• Trimmy Fix
• 503 97 71-01 / 503 93 42-02
• Trimmy Hit 1"
• 503 97 71-01 / 503 93 42-02
• Trimmy Hit Pro
• 503 97 71-01 / 503 93 42-02
• Superauto II 1"
• 503 97 71-01 / 503 93 42-02
• S35
• 503 97 71-01 / 503 93 42-02
• T35
• 503 97 71-01 / 503 93 42-02
• YOUR WARRANTY RIGHTS AND OBLIGATIONS
• The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the em...
• MANUFACTURER¢S WARRANTY COVERAGE
• The 2001 and later small nonroad engines are warranted for two years. If any emission related part on you engine (as listed above) is defective, the part will be repaired or replaced by Husqvarna Forest & Garden.
• OWNER¢S WARRANTY RESPONSIBILITIES
• As the small nonroad engine owner, you are responsible for the performance of the required maintenance listed in your Operator¢s...
• WARRANTY COMMENCEMENT DATE
• The warranty period begins on the date small nonroad engine is delivered.
• LENGTH OF COVERAGE
• Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.
• WHAT IS COVERED
• REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no charge to the owner at an app...
• WARRANTY PERIOD Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only fo...
• DIAGNOSIS The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an approved Husqvarna Forest & Garden servicing dealer.
• CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden may be liable for damages to other engine components caused by the failure of a warranted part still under warranty.
• WHAT IS NOT COVERED
• All failures caused by abuse, neglect or improper maintenance are not covered.
• ADD -ON OR MODIFIED PARTS
• The use of add-on or modified parts can be grounds for disallowing a warranty claim. Husqvarna Forest & Garden is not liable to cover failures of warranted parts caused by the use of add-on or modified parts.
• HOW TO FILE A CLAIM
• If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-800- 487-5963.
• WHERE TO GET WARRANTY SERVICE
• Warranty services or repairs shall be provided at all Husqvarna Forest & Garden authorized servicing dealers.
• MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
• Any Husqvarna Forest & Garden approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without charge to the owner if the part is under warranty.
• EMISSION CONTROL WARRANTY PARTS LIST
• 1 Carburetor and internal parts
• 2 Intake pipe, airfilter holder and carburetor bolts.
• 3 Airfilter and fuelfilter covered up to maintenance schedule.
• 4 Ignition System
• 1 Spark Plug, covered up to maintenance schedule
• 2 Ignition Module
• 5 Muffler with catalytic converter
• MAINTENANCE STATEMENT
• The owner is responsible for the performance of all required maintenance, as defined in the operator’s manual.