Document Outline

• COVER PAGE 10.3.07.doc
• TABLE OF CONTENT 10.3.07.doc
  • TABLE OF CONTENTS
• PAGE 1-2 10.3.07.doc
• PAGE 3 10.3.07.doc
• PAGE 4 10.3.07.doc
  • • CALIFORNIA PROPOSITION 65-WARNING
• PAGE 5 10.3.07.doc
  • LOCATION
• PAGE 6 10.3.07.doc
• PAGE 7 10.3.07.doc
  • SIDE SHELF HANDLE ASSEMBLY
  • BATTERY INSTALLATION
  • 1. Remove the ignition button housing.
  • 2. Insert the battery into the housing with the positive (+) terminal facing outward.
  • 3. Replace the ignition button housing after the battery has been installed.
• PAGE 8 10.3.07.doc
  • BRAKING SYSTEM OPERATIONS
    • LIQUID PROPANE CYLINDER RETENTION SYSTEM
• PAGE 9 10.3.07.doc
• PAGE 10-12 10.3.07.doc
  • LIQUID PROPANE CYLINDER REQUIREMENTS
  • (20 lb. Cylinder)
  • GENERAL
    • It is handy to keep a spray bottle of soapy water near the shut-off valve of the gas supply line. Spray all the fittings. Bubbles indicate leaks.
      • Disconnected liquid propane cylinders must have threaded valve plugs tightly installed, and must not be stored in a building, garage or any other enclosed area.
      • The gas must be turned off at the supply cylinder when the unit is not in use.
      • If the appliance is stored indoors, the cylinder must be disconnected and removed from the appliance.
      • Cylinders must be stored outdoors in a well-ventilated area out of the reach of children.
• PAGE 13-14 10.3.07.doc
  • WARNING
  • The rotisserie motor is equipped with a plug and should be plugged directly into a properly grounded receptacle in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. DO NOT cut or remove the grounding prong from this plug.
  • Keep the rotisserie motor cord away from the heated surfaces of the grill. When not in use remove and store the motor in a dry location.
  • • • BEFORE LIGHTING…
        • WARNING
• PAGE 15 10.3.07.doc
• PAGE 16-18 10.3.07.doc
  • TO MATCH LIGHT THE GRILL
• Page 19 10.3.07.doc
• Page 20 10.3.07.doc
• PAGE 21-22 10.3.07.doc
  • LIGHTING INSTRUCTIONS
  • MATCH LIGHTING
  • STAINLESS STEEL
  • GRILL RACK
  • GRILL BURNERS
  • WARNING
  • Failure to properly place the burner over the orifice could cause a fire to occur behind and beneath the valve panel, thereby damaging the grill and making it unsafe to operate.
  • GRILL BURNER REMOVAL/INSTALLATION
  • The grill burners are factory installed.
  • To remove the main burners for cleaning:
  • 1. Locate the nut at the rear of the burner on the bottom side.
  • 2. Remove the nut and lift the burner out of the fire box.
  • To reinstall the main burners:
  • 3. Insert the burner over the valve assembly (Item# 20 on page 24).
  • 4. Insert the back of the burner into the hole at the rear of the fire box and reinstall the nut.
  • 5. Make sure orifice spud is inside the burner’s venturi as shown below.
• PAGE 23 10.3.07.doc
  • • BEFORE CALLING FOR SERVICE
• PAGE 24 10.3.07.doc
• PAGE 25-26 10.3.07.doc
• PAGE 27-29 10.3.07.doc
  • WARNING
• PAGE 30-31 10.3.07.doc
  • BBQ SALMON
  • Preheat the BBQ
  • BAKED CHILI CORN
  • TANGY SEAFOOD KABOBS
  • PORK CHOPS
  • BARBECUED LONDON BROIL
  • VEGETABLE KABOBS
    • FAJITAS
    • BEEF AND LAMB KABOBS
    • EGGPLANT CAVIAR
    • CHICKEN TANDOORI STYLE
    • SPARE RIBS
    • PORK ROAST
    • TURKEY
• PAGE 32 10.3.07.doc
  • LIMITED WARRANTY
  • MODEL #720-0511
  • STAINLESS STEEL OUTDOOR GAS GRILL