KEPCO RA 19-1U Operator Manual Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for RA 19-1U Operator Manual KEPCO
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 44 |
| Size: | 2.04 MB |
Show table of contents
Read manual
Document Outline
- SECTION 1 - INTRODUCTION
- SECTION 2 - INSTALLATION
- FIGURE 1-1. RA 19-1U Rack Adapter
- SECTION 1 - INTRODUCTION
- 1.1 Scope of Manual
- 1.2 General Description
- FIGURE 1-2. RA 19-1U Rack Adapter with 1U HSF Power Supplies Installed
- 1.3 Mechanical
- 1.4 Electrical
- FIGURE 1-3. RA 19-1U Interconnections, Simplified Diagram
- 1.5 Safety
- 1.6 RoHS Compliance
- 1.7 Accessories
- 1.8 Options
- FIGURE 1-4. RA 19-1U Rack Adapter Rear Panel
- TABLE 1-1. Compatible 1U HSF Power Supplies
- TABLE 1-2. RA 19-1U Accessories
- FIGURE 1-5. Mechanical Outline Drawing, RA 19-1U Rack Adapter
- FIGURE 1-6. RA 19-1U Schematic Diagram
- SECTION 2 - INSTALLATION
- 2.1 Unpacking and Inspection
- TABLE 2-1. Equipment Supplied
- 2.2 Configuring the Rack Adapter
- 2.3 Rack Adapter Keying Instructions
- 2.3.1 Establishing Key Positions
- FIGURE 2-1. RA 19-1U Rack Adapter Keying
- 2.4 Slot Configuration
- TABLE 2-2. Rear Panel DIP Switch Functions
- 2.4.1 Independent Operation
- 2.4.1.1 Independent Operation - Local Sensing Using Rear Panel DIP switches
- FIGURE 2-2. Independent Operation, Local Sensing for PS1 and PS2 using Rear Panel DIP switches, Simplified Diagram
- 2.4.1.2 Independent Operation - Local Sensing Using External Wiring
- FIGURE 2-3. Independent Operation, Local Sensing for PS1 and PS2 using External Jumpers at I/O Mating Connector, Simplified Diagram
- 2.4.1.3 Independent Operation - Remote Sensing
- FIGURE 2-4. Independent Operation, Remote Sensing for PS1 and PS2 using External Wiring at I/O Mating Connector, Simplified Diagram
- 2.4.2 Parallel Operation
- 2.4.2.1 Parallel DC OUTPUT Connections
- 2.4.2.2 Parallel Current Share Connections
- 2.4.2.2.1 Parallel Current Share - Rear Panel DIP Switches
- FIGURE 2-5. Parallel Outputs Using Rear Panel DIP Switches to Parallel sense lines and current share, PS1 and PS2 (Typical), Simplified Diagram
- 2.4.2.2.2 Parallel Current Share - External Wiring
- FIGURE 2-6. Parallel Outputs Using External Wiring, Typical Configuration, Simplified Diagram
- 2.4.2.3 Sense Connections for Parallel Configurations
- 2.4.2.3.1 Parallel Configuration Using DIP Switches to Connect Sense Lines in Parallel and External Wires to Configure Local Sensing
- FIGURE 2-7. Typical Parallel Connections Using External Wires for Local Sensing and DIP switches to Parallel Sense Wires
- 2.4.2.3.2 Parallel Configurations using External Wires to Connect Sense Lines in Parallel and External Wires to Configure Local Sensing
- FIGURE 2-8. Typical Parallel Connections using External Wires for Local Sensing and I/O Mating Connector Jumpers to Parallel Sense Wires
- 2.4.2.3.3 Parallel Configurations using DIP Switches to Connect Sense Lines in Parallel and External Wires to Configure Remote Sensing
- FIGURE 2-9. Typical Parallel Connections, Remote Sensing using DIP Switches to Parallel Sense Wires
- 2.4.2.3.4 Parallel Configurations using External Wires to Connect Sense Lines in Parallel and External Wires to Configure Remote Sensing
- FIGURE 2-10. Typical Parallel Connections, Remote Sensing using I/O Mating Connector Jumpers to Parallel Sense Wires
- 2.4.3 Series Operation
- FIGURE 2-11. Series Configuration, Simplified Diagram
- 2.4.4 Alarm Configurations
- 2.4.4.1 N.O. Alarm Line (Close on Failure)
- 2.4.4.1.1 Close on Failure Using Rear Panel Dip Switches
- FIGURE 2-12. Close on Failure Alarm Configuration Using Rear Panel Dip Switches, Simplified Diagram
- 2.4.4.1.2 Close on Failure Using External Wiring at I/O Mating Connector
- FIGURE 2-13. Close on Failure Alarm Configuration Using External Wiring at I/O Mating Connector, Simplified Diagram
- 2.4.4.2 N.C. Alarm Line (Open on Failure)
- 2.4.4.2.1 Open on Failure Using Rear Panel Dip Switches
- FIGURE 2-14. Open on Failure Alarm Configuration Using Rear Panel Dip Switches, Simplified Diagram
- 2.4.4.2.2 Open on Failure Using External Wiring of I/O Mating Connector
- FIGURE 2-15. Open on Failure Alarm Configuration Using External Wiring at I/O Mating Connector, Simplified Diagram
- 2.5 Current Monitoring (-1URC and -1URY Models only)
- TABLE 2-3. Sense Resistor Values
- FIGURE 2-16. Using Current Monitoring (Typical), -1URC and -1URY Models only
- 2.6 Remote On-Off (-1URX and -1URY Models only)
- FIGURE 2-17. Using Remote On-Off (Typical), -1URX and -1URY Models only
- 2.7 Terminations
- 2.8 Cooling
- 2.9 Installation
- 2.9.1 Installing 1U HSF Power Supplies
- 2.10 Wiring Instructions
- 2.10.1 Safety Grounding
- 2.10.2 Source Power Connections
- 2.10.2.1 EMI Compliance
- 2.10.3 Control Signal Connections
- 2.10.4 Output Load Connections
- 2.10.4.1 Reducing Ripple and Noise
- FIGURE 2-18. Ripple and Noise Measurement Setup Diagram
- 2.10.4.2 Parallel/Redundant Operation
- 2.10.4.3 Series/Independent Operation
- 2.10.4.4 Mixed Operation
- 2.11 Removing/Replacing 1U HSF Power Supplies
- 2.12 Shipping