Document Outline

• 1 Introduction
  • 1.1 About this Manual
  • 1.2 Manual Organization
  • 1.3 What Your Server Includes
  • 1.4 Product Accessories
  • 1.5 Additional Information and Software
• 2 Features
  • 2.1 Server Components
  • 2.2 CG2100 Server Front Panel
  • 2.3 CG2100 Server Back Panel
  • 2.4 Front Panel Board
  • 2.5 LED/Switch Board
  • 2.6 Hard Disk Drives
  • 2.7 SD Flash Module
  • 2.8 Server Board (Baseboard)
  • 2.9 Riser Card Assembly
  • 2.10 Ethernet NIC Ports
  • 2.11 Remote Management Module 3
  • 2.12 Power Supply Subsystem
  • 2.13 System Cooling
  • 2.14 Processors and Memory DIMMs
    • Processors
    • Memory
• 3 Standard Component Installations and Upgrades
  • 3.1 Before You Begin
    • Tools and Supplies Needed
    • System References
  • 3.2 General Installation Procedures
    • Removing the Chassis Covers
      • Removing the Front Cover
      • Removing the Back Cover
    • Re-installing the Chassis Covers
      • Re-Installing the Back Cover
      • Re-Installing the Front Cover
    • Removing the Front Bezel
    • Re-Installing the Front Bezel
    • Removing the Riser Card Assembly
    • Re-Installing the Riser Card Assembly
    • Removing the Processor Air Duct
    • Re-Installing the Processor Air Duct
  • 3.3 Internal System Components Configuration and Installation Procedures
    • Configuring Memory DIMMs
      • Intel® QuickPath Memory Controller
    • Supported Memory
    • Publishing System Memory
    • Memory Map and Population Rules
      • Memory Population Rules
    • Memory RAS
      • Channel Independent Mode
      • Channel Mirroring Mode
        • Minimum DDR3 DIMM Population for Channel Mirroring
        • Mirroring DIMM Population Rules Variance Across Nodes
    • Memory Upgrade Rules
    • Installing Memory DIMMs
    • Replacing or Removing Memory DIMMs
    • Adding or Replacing a Processor
      • ESD and Processor Handling Precautions
      • Removing a Processor
      • Installing a New Processor
    • Inserting the Heat Sink
    • Configuring Jumpers on the Server Board
• 4 Optional Component Installation Procedures
  • 4.1 Before You Begin
    • Tools and Supplies Needed
    • System References
    • Cable Routing Reference
  • 4.2 Installing or Replacing Hard Disk Drives
    • Removing an HDD Carrier from the Chassis
    • Installing a Hard Drive in a Carrier
  • 4.3 Installing a SAS/SATA Control Module
  • 4.4 Installing a Hardware RAID Module
  • 4.5 Installing a RAID Intelligent Battery Backup Unit (IBBU)
  • 4.6 Adding a Second Power Supply Module
  • 4.7 Installing a PCI Riser Card
  • 4.8 Installing PCI Add-in Cards
  • 4.9 Installing a Personality Module
  • 4.10 Installing a Remote Management Module
  • 4.11 Installing an SD Flash Module
  • 4.12 Installing a USB Solid-State Drive
    • Installing a Solid-State Drive on the Front Panel Board
    • Installing a Solid-State Drive on the Server Board
  • 4.13 Installing the Server into a Rack
    • Connecting the Power Cord
    • Equipment Rack Precautions
• 5 Server Component Replacements
  • 5.1 Before You Begin
    • Tools and Supplies Needed
    • System References
    • Cable Routing Reference
  • 5.2 Replacing Fans
    • Replacing 80mm CPU Fans
    • Replacing 60mm PCI Fans
  • 5.3 Replacing the Bridge Board
    • Removing the Bridge Board
      • Disconnecting the Flex Circuit Cable
      • Removing the Guide Bracket and Releasing the Bridge Board
    • Re-Installing the Bridge Board
  • 5.4 Replacing the Front Panel Board
    • Removing the Old Front Panel Board
    • Installing the New Front Panel Board
  • 5.5 Replacing the LED/Switch Board
    • Removing the Old LED/Switch Board
    • Replacing the LED/Switch Light Pipe Assembly
    • Installing the New LED/Switch Board
  • 5.6 Replacing the Telco Alarms Module (TAM)
    • Removing the Old Telco Alarms Module
    • Installing the New Telco Alarms Module
  • 5.7 Replacing the Power Distribution Board
    • Removing the Old Power Distribution Board
    • Installing the New Power Distribution Board
  • 5.8 Replacing the T5520UR Server Board
    • Removing the Old Server Board from the Chassis
    • Installing the New Server Board
  • 5.9 Replacing the SAS/SATA Backplane Board
    • Removing the Old SAS/SATA Backplane Board
    • Installing the New SAS/SATA Backplane Board
• 6 Server Utilities
  • 6.1 Using the BIOS Setup Utility
    • Using BIOS Setup
    • Starting Setup
    • If You Cannot Access Setup
    • Setup Menus
  • 6.2 Upgrading the BIOS
    • Preparing for the Upgrade
      • Obtaining the Upgrade
    • Updating the BIOS
  • 6.3 Restoring BIOS Default Settings
  • 6.4 Clearing the Password
  • 6.5 BMC Force Update Procedure
• 7 Troubleshooting
  • 7.1 Resetting the System
  • 7.2 Problems Following Initial System Installation
    • First Steps Checklist
  • 7.3 Hardware Diagnostic Testing
    • Verifying Proper Operation of Key System Lights
    • Confirming the Operating System Load
  • 7.4 Specific Problems and Corrective Actions
    • Power Light does not Light
    • No Characters Appear on Screen
    • Characters are Distorted or Incorrect
    • System Cooling Fans do not Rotate Properly
    • Cannot Connect to a Server
    • Diagnostics Pass but the Connection Fails
    • The Controller Stopped Working When an Add-in Adapter was Installed
    • The Add-in Adapter Stopped Working without Apparent Cause
    • System Boots When Installing a PCI Card
    • Problems with Newly Installed Application Software
    • Problems with Application Software that Ran Correctly Earlier
    • Devices are not Recognized under Device Manager (Windows*OS)
    • Hard Drive(s) are not Recognized
  • 7.5 LED Information
    • BIOS POST Beep Codes
• 8 Warranty
• 9 Appendix A: Safety Information
  • 9.1 Emissions Disclaimer
  • 9.2 Intended Uses
    • If AC power supplies are installed:
    • If DC power supplies are installed:
    • Temperature and Ventilation
  • 9.3 Safety Cautions
    • Wichtige Sicherheitshinweise
    • Consignes de sécurité
    • Instrucciones de seguridad importantes
• 10 Appendix B: Regulatory and Certification Information
  • 10.1 Product Regulatory Compliance
    • Product Safety Compliance
    • Product EMC Compliance - Class A Compliance
    • Certifications/Registrations/Declarations
  • 10.2 Electromagnetic Compatibility Notices
    • FCC (USA)
    • Industry Canada (ICES-003)
      • English translation of the notice above:
    • Europe (CE Declaration of Conformity)
    • VCCI (Japan)
      • English translation of the notice above:
    • BSMI (Taiwan)
    • Regulated Specified Components
• 11 Appendix C: Getting Help
  • 11.1 World Wide Web
  • 11.2 Telephone
  • 11.3 Email