Document Outline

• EDS84DG752
  • Contents
  • 1 About this documentation
    • 1.1 Validity information
    • 1.2 Document history
    • 1.3 Conventions used
    • 1.4 Terms and abbreviations used
    • 1.5 Notes used
  • 2 Safety instructions
    • 2.1 General safety and application notes for Lenze controllers
    • 2.2 General safety and application instructions for Lenze motors
    • 2.3 Residual hazards
  • 3 Product description
    • 3.1 System overview
    • 3.2 Device features
    • 3.3 Identification
    • 3.4 Type code
      • 3.4.1 Introducing information
      • 3.4.2 The type codes
    • 3.5 Overview of control terminals
  • 4 Technical data
    • 4.1 General data and operating conditions
    • 4.2 Rated data
      • 4.2.1 Overview
      • 4.2.2 Operation at rated mains voltage 400 V
      • 4.2.3 Operation at increased rated power at 400 V mains voltage
      • 4.2.4 Operation with rated mains voltage 480 V
    • 4.3 Switching frequency reduction
    • 4.4 Overcurrent operation
    • 4.5 Terminal description
      • 4.5.1 Overview
    • 4.6 Power terminals
      • 4.6.1 Mains connection
      • 4.6.2 Motor connection
      • 4.6.3 Motor temperature monitoring
      • 4.6.4 Motor holding brake connection
      • 4.6.5 Connection of brake resistor
    • 4.7 Control terminals
      • 4.7.1 Digital inputs
      • 4.7.2 Digital output
      • 4.7.3 Analog input
      • 4.7.4 Connection of relay output
      • 4.7.5 Communication connection
    • 4.8 Dimensions
      • 4.8.1 Standard motor mounting
      • 4.8.2 Wall mounting
  • 5 Installation
    • 5.1 Important notes
    • 5.2 Installation according to EMC (installation of a CE-typical drive system)
      • 5.2.1 Shielding
      • 5.2.2 Motor cable
      • 5.2.3 Control cables
      • 5.2.4 Detecting and eliminating EMC interferences
    • 5.3 Mechanical installation
    • 5.4 Electrical installation
      • 5.4.1 Power connections
      • 5.4.2 Wiring of control connections
    • 5.5 Installation of 8400 motec pre-assembled on the motor
      • 5.5.1 Plug at the Wiring Unit
      • 5.5.2 Attaching the cable gland
    • 5.6 Retrofitting the 8400 motec controller
      • 5.6.1 Preparing a motor for the 8400 motec installation
      • 5.6.2 Mounting the Wiring Unit
      • 5.6.3 Mounting of the Communication Unit
      • 5.6.4 Settings at the Drive Unit
      • 5.6.5 Mounting of the Drive Unit
    • 5.7 Measures when drive is used in IT systems
    • 5.8 Wall mounting of 8400 motec controller
  • 6 Commissioning
    • 6.1 Before switching on
    • 6.2 Quick commissioning
      • 6.2.1 General configuration settings
      • 6.2.2 Commissioning steps
    • 6.3 Handling of the keypad
    • 6.4 Overview of the commissioning steps with keypad
      • 6.4.1 Keypad control
      • 6.4.2 Short overview of the parameters for quick commissioning
    • 6.5 Setting with the diagnosis terminal (keypad)
    • 6.6 Diagnostics
      • 6.6.1 Drive diagnostics via the integrated display
      • 6.6.2 Diagnostic codes
  • 7 Braking operation
    • 7.1 Braking operation without additional measures
    • 7.2 Braking operation with brake resistor
      • 7.2.1 Selection of the brake resistors
      • 7.2.2 Wiring of brake resistor
    • 7.3 Operation with spring-applied brake
      • 7.3.1 Introduction
      • 7.3.2 Wiring
  • 8 Safety engineering
    • 8.1 Introduction
    • 8.2 Important notes
      • 8.2.1 Hazard and risk analysis
      • 8.2.2 Standards
    • 8.3 Basics for safety sensors
    • 8.4 Operating mode
      • 8.4.1 Introduction
      • 8.4.2 Disconnecting paths
      • 8.4.3 Safety status
    • 8.5 Technical data
    • 8.6 Electrical installation
    • 8.7 Certification
  • 9 Accessories (overview)
    • 9.1 Adapter plates (accessories)
    • 9.2 Plug connectors
    • 9.3 Internal brake resistors
    • 9.4 External brake resistors
    • 9.5 Communication modules
      • 9.5.1 CANopen
      • 9.5.2 PROFIBUS
      • 9.5.3 AS interface
      • 9.5.4 PROFINET
      • 9.5.5 EtherCAT
      • 9.5.6 EtherNet/IP
    • 9.6 Keypad
    • 9.7 Safety engineering
  • 10 Appendix
    • 10.1 Total index
  • ©