Document Outline

• EDS84DPS424
  • Contents
  • About this documentation
    • Document history
    • Conventions used
    • Terms and abbreviations used
    • Notes used
  • Safety instructions
    • General safety and application notes for Lenze controllers
    • General safety and application instructions for Lenze motors
    • Residual hazards
  • Product description
    • Device features
    • Identification
    • Type code
    • Overview of standard devices
    • Communication
      • CAN port
      • Infrared remote control receiver
      • Extensions in EMS version
      • Infrared interface
    • Concepts for the mains connection
      • Concepts for the connection of individual axes
      • Concepts for the connection of the power bus
    • EMS mains connection concepts
      • Half wave (coded)
      • Power wave
      • DECA bus
      • Inductive
  • Technical data
    • General data and operating conditions
    • Rated data
      • Overview
      • Operation at rated mains voltage 400 V
      • Operation at a rated mains voltage of 500 V
    • Current characteristics
    • Overcurrent operation
    • Terminal description
    • Supply concept of control voltage
      • Internal 24 V supply voltage
      • External supply voltage 24 V
    • Control terminals
      • Digital inputs
      • Digital outputs
      • Analog inputs
      • Synchronous serial interface (SSI)
      • Remote control (IrRC)
      • Interfaces of the EMS version
      • Motor holding brake connection
  • Mechanical installation
    • Important notes
    • Dimensions
    • Mounting clearance
  • Electrical installation - HighLine/StateLine version
    • Important notes
      • Electrical isolation
      • Device protection
      • Maximum motor cable length
      • Motor protection
    • Safety instructions for the installation according to UL or UR
    • Safety instructions for the installation according to UL or UR
    • Installation according to EMC (installation of a CE-typical drive system)
      • Shielding
      • Motor cable
      • Control cables
      • Wiring
      • Detecting and eliminating EMC interferences
    • Devices in a power range of 0.75 ... 7.5 kW (3/PE AC 400 V)
      • Example circuits
      • Terminal assignment of the power connections
    • Control terminals
      • Diagnostics
      • Analog input
      • Digital inputs and outputs
      • Synchronous serial interface (SSI)
    • Communication
      • PROFINET® / EtherNet/IP™
      • PROFIBUS®
      • CANopen®
      • CAN on board
    • Safety engineering
  • Electrical installation - EMS version
    • Important notes
      • Electrical isolation
      • Device protection
      • Maximum motor cable length
      • Motor protection
    • Safety instructions for the installation according to UL or UR
    • Safety instructions for the installation according to UL or UR
    • Installation according to EMC (installation of a CE-typical drive system)
      • Shielding
      • Motor cable
      • Control cables
      • Wiring
      • Detecting and eliminating EMC interferences
    • Devices in a power range of 0.75 ... 4 kW (3/PE AC 400 V)
      • Example circuits
      • Terminal assignment of the power connections
    • Control terminals
      • Diagnostics
      • Digital inputs and outputs
      • Synchronous serial interface (SSI)
      • Interfaces RS485/422 PLC
      • Interfaces RS485 PLC
      • Interfaces RS422 PLC
    • Communication
      • CANopen
      • CANopen master PLC
  • Commissioning
    • Before switching on
    • Preparing the commissioning procedure
    • Quick commissioning
      • Keypad control
      • Terminal control
  • Braking operation
    • Braking operation without additional measures
    • Braking operation with external brake resistor
      • Selection of the brake resistors
      • Wiring of brake resistor
    • Operation with spring-applied brake
      • Introduction
      • Wiring
  • Diagnostics
    • Display of operating data, diagnostics
      • Status display via controller LEDs
      • Extensions in EMS version
      • Status display of the safety system via LEDs at the controller
      • Drive diagnostics via the integrated display
      • Drive diagnostics
  • Safety engineering
    • Introduction
    • Important notes
    • Overview of safety options
  • Accessories (overview)
    • Overview
    • System cables
      • Motor cable
      • Incremental HTL encoder
      • Connection of external brake resistor
      • Connection of safety sensors and actuators
    • Memory module
      • E84AYM10S
      • E84AYM30S
    • Diagnosis terminal
    • Infrared remote control (IrRC)
    • External brake resistors
    • Power supply units
    • EMS accessories
  • Appendix
    • Declarations and certificates
    • Total index
  • ©