Document Outline

• Battery Cabinet Precautions
• Contacting Liebert for Support
• Important Safety Instructions
• 1.0 Introduction
  • 1.1 System Description
  • 1.2 Reliability
    • Designed for Success
    • Other Factors to Consider
  • 1.3 Safety Precautions
  • 1.4 Modes of Operation
    • 1.4.1 Normal-Load on UPS
    • 1.4.2 Input Power Failure
    • 1.4.3 Recharge
    • 1.4.4 Overload
    • 1.4.5 Bypass-Internal
    • 1.4.6 Maintenance Bypass
    • 1.4.7 Off-Battery
  • 1.5 Operator Controls
    • Figure 1 UPS controls and display screen with example of the Monitor/Mimic screen
  • 1.6 Options
• 2.0 Theory of Operation
  • 2.1 General Component Descriptions
    • UPS Module
    • Battery Plant
  • 2.2 Detailed Component Descriptions
    • 2.2.1 Controls
      • Hardware
      • Software
    • 2.2.2 Rectifier/Charger
      • Operation
      • Input Circuit Breaker
      • Isolation Transformer
      • Input Current Limit
      • Input Current Inrush
      • Input Power Factor
    • 2.2.3 Battery Charging Circuit
      • Operation After Discharge
      • Operation After End-of-Discharge
      • Battery Disconnect
      • Battery Charge Current Limiting
      • Battery Equalize Charge Circuit
    • 2.2.4 Inverter
      • Operation
      • Output Regulation and Overload Performance
      • Non-Linear Load Characteristics
      • Unbalanced Load Characteristics
    • 2.2.5 Static Bypass
      • Bypass Circuit Breaker
      • Pulsed Parallel Operation
      • Load Transfers
      • Fuse Protection
      • Static Switch Backfeed Protection
      • Transfer and Retransfer Conditions
        • Figure 2 Typical UPS system one-line diagram with optional maintenance bypass
• 3.0 Operation
  • 3.1 Display Screen and Operator Controls
    • Features
      • Figure 3 Operator controls, typical system
      • Figure 4 Series 610 UPS operator control panel
  • 3.2 Menu Tree Navigation
    • Figure 5 Menu tree
    • 3.2.1 Master Menu Screen
      • Figure 6 Master menu screen
    • 3.2.2 Monitor/Mimic Display Screen
      • Figure 7 Monitor/Mimic display screen
      • Input Metering Displays
      • Output Metering Displays
      • Status/Alarm Message Areas
        • Figure 8 Monitor/Mimic display example: Normal power flow
        • Figure 9 Monitor/Mimic display example: Utility fail
        • Figure 10 Monitor/Mimic display example: Load on bypass, UPS module on and charging battery
        • Figure 11 Monitor/Mimic display example: Load on bypass, UPS module off
    • 3.2.3 Walk-In Display Screen
      • Figure 12 Walk-in display screen
    • 3.2.4 Status Reports Screens
      • Figure 13 Status reports screen
      • Present Status
        • Figure 14 Present status report screens
      • Event History
        • Figure 15 Event history report screen
      • History Status
        • Figure 16 History status report screen
      • System Status
        • Figure 17 Battery cycle monitor screen
        • Figure 18 Battery cycle monitoring summary screen
        • Figure 19 Typical data on discharge cycles of 91 to 240 seconds duration during the recording period
    • 3.2.5 System Configuration Screens
      • Figure 20 System configuration screens
      • Maximum Auto-Retransfer Attempts
        • Figure 21 Maximum auto-retransfer attempts screen
      • Date
        • Figure 22 Date screen
      • Time
        • Figure 23 Time screen
      • Auto Dial
        • Figure 24 Auto dial screen
      • Language Selection
      • System Options
        • Figure 25 System options screen
        • Figure 26 Battery test screen
        • Figure 27 Battery test results screen
        • Figure 28 Monitor/Mimic display example: Continuous Duty Static Switch
      • Remote Monitor
        • Table 1 Alarm messages
        • Table 2 Additional alarm messages
    • 3.2.6 Alarm Limit Settings Screen
      • Figure 29 Alarm limit settings screen
      • Overload Alarm
      • DC Overvoltage
      • Battery Discharging
      • Low Battery
      • Battery Shutdown (15 Minutes)
      • Battery Shutdown (60 Minutes)
      • Battery Rating (100%)
      • Battery Rating
      • Temperature Limit Setting (Optional)
    • 3.2.7 Load Transfer Procedures Screen
      • Figure 30 Load transfer procedure screen
    • 3.2.8 Start-Up Procedures Screen
      • Figure 31 Start-up procedures screen
      • Figure 32 Start-up procedures screen, continued
    • 3.2.9 Shutdown Procedures Screen
      • Figure 33 Shutdown procedures screen
      • Figure 34 Shutdown procedures screen, continued
    • 3.2.10 Battery Time Screen
      • Figure 35 Battery time screen (15-minute discharge)
      • Figure 36 Battery time screen (45-minute discharge)
      • Figure 37 Accuracy range of values for calculated battery times
    • 3.2.11 Meter Calibration Screen
      • Figure 38 Meter calibration screen
    • 3.2.12 Battery Equalize Screen
      • Figure 39 Battery equalize screen
    • 3.2.13 Alarm and Status Messages
      • Status Messages
        • Figure 40 Alarm and status message screen
      • Alarm Messages
        • Table 3 Abbreviations used in alarm messages
        • Table 4 Alarm messages and corrective actions
        • Table 5 Alarm messages-summary
    • 3.2.14 Communication Interfaces
      • Worldwide Reporting
      • Local Reporting to a Terminal
      • Local Reporting to a Monitor
      • Site Reporting: SiteScan or SNMP
      • Remote Monitor Panel
      • Separate / Simultaneous Outputs
        • Table 6 Series 610 terminal commands
  • 3.3 Modes of Operation
    • Table 7 Circuit breaker abbreviations
    • 3.3.1 Load on Bypass
      • Figure 41 Load on bypass (UPS not available)
    • 3.3.2 OK to Transfer
      • Figure 42 Load on bypass (UPS available)
      • Figure 43 Load on UPS (bypass available)
    • 3.3.3 Momentary Overloads
      • Figure 44 Momentary overload (through pulse-parallel static switch)
    • 3.3.4 Input Power Failure-Load on Battery
      • Figure 45 Input power fail-load on battery
    • 3.3.5 Off Battery
      • Figure 46 Load on UPS-battery not available
    • 3.3.6 Emergency Module Off
      • Figure 47 Emergency modules off
    • 3.3.7 Remote Emergency Power Off
      • Figure 48 Emergency power off
    • 3.3.8 Module Shutdown
      • Figure 49 Module shutdown
    • 3.3.9 Maintenance Bypass
      • Figure 50 Load on maintenance bypass (two breakers)
      • Figure 51 Load on maintenance bypass (three breakers)
  • 3.4 Manual Procedures
    • 3.4.1 Start-Up Procedure
      • Figure 52 Start-up procedures screen
      • Figure 53 Start-up procedures, continued
    • 3.4.2 Load Transfer Procedures
      • Figure 54 Load transfer procedures screen
    • 3.4.3 Maintenance Bypass Load Transfers
    • 3.4.4 Shutdown Procedures
      • Module Shutdown Procedure
        • Figure 55 Shutdown procedures screen
        • Figure 56 Shutdown procedures screen, continued
      • Local Emergency Modules Off (LEMO)
      • Remote Emergency Power Off (REPO)
    • 3.4.5 Battery Exercise Procedures
      • Figure 57 Battery exercise control screen (above) and results (below)
  • 3.5 Automatic Operations
    • 3.5.1 Overloads (Without Transfer)
      • Figure 58 Current-versus-time curves of overload capacity
    • 3.5.2 Automatic Transfers to Bypass (Overload Condition)
    • 3.5.3 Automatic Retransfers to UPS
    • 3.5.4 Automatic Transfers to Bypass (UPS System Faults)
    • 3.5.5 Automatic Restart (Optional)
      • Enabling Automatic Restart
      • Sequence of Operation
• 4.0 Maintenance
  • 4.1 Safety Precautions
  • 4.2 Liebert Global Services
    • Professional Start-Up
    • Maintenance Agreements: The Signature Program
    • Training
    • Warranties
  • 4.3 Routine Maintenance
    • 4.3.1 Record Log
    • 4.3.2 Air Filters
    • 4.3.3 Limited Life Components
  • 4.4 Battery Maintenance
    • 4.4.1 Battery Safety Precautions
      • Battery Safety Precautions In French Per CSA Requirements
      • Instructions Importantes Concernant La Sécurité Conserver Ces Instructions
      • Matching Battery Cabinets (Optional)
        • Table 8 Battery retorque values
      • Rack-Mounted Batteries
        • Table 9 Battery voltage record
    • 4.4.2 Torque Requirements
      • Table 10 Torque specifications (unless otherwise labeled)
  • 4.5 Detection of Trouble
  • 4.6 Reporting a Problem
  • 4.7 Corrective Actions
  • 4.8 Recommended Test Equipment
    • Table 11 Recommended test equipment and tools
  • 4.9 Upstream Feeder Circuit Breaker Setting Inspections
• 5.0 Specifications
  • 5.1 Rating
    • Figure 59 Output power envelope for 0.8 and 0.9 pf rated units
  • 5.2 Environmental Conditions
    • Table 12 Specifications applicable to environment
  • 5.3 Adjustments
  • 5.4 Battery Operation
  • 5.5 Electrical Specifications