Document Outline

• iCOM
• Temperature Control Program Types
  • Intelligent Control – Factory Default Setting
    • Membership
      • Consequence
  • Proportional (P) Control
  • Proportional + Integral (PI) Control
  • Proportional + Integral + Derivative (PID) Control
    • In the chart above we are defining the Digital Compressor st
      • Note that the Digital Scroll will run continuously while the
        • Optional Glycool (Econ-O-Cycle) Cooling
• Staged Electric Reheat
• Humidity Control Program Types
  • Absolute (predictive) Humidity Control – Factory Default Set
• When absolute humidity control is used, over dehumidificatio
  • Relative Humidity Control
• Autoflush Control for Infrared Large (IFL) or Small (IFS) Pa
• Reheating during Dehumidification
  • Auto restart
• High Pressure Cutout
• Suction Pressure Transducer
• Call for Cooling
  • Next Maintenance Calculation
    • Foreword
    • Calculation of next Maintenance Parameters
      • Parameters for next Maintenance Calculation:
        • General Maintenance Settings:
          • Example: 2 Units, One Large Display and One Small Display
            • Example: Large Wall Display and Five Units with Small Displa
              • Example: 4 Units in 2 Groups with 2 Large Displays
  • Teamwork Modes
    • “No” Teamwork
    • Teamwork Mode 1
    • Unit Lead/ Lag or Running/ Standby Function
      • Typical Lead/ Lag (Running/ Standby) Function
      • The Lead/ Lag function may be used in the either the No Team
• Status Display
  • The User menu displays the various unit operating values and
    • User Menu: Spare Parts List, Large Display Only
      • User Menu: Event Log
        • Range
        • User Menu: Set Alarm Parameters U200 series
        • Parameter
        • User Menu: Total Run Hours Parameters U500 series
        • User Menu: Sleep Mode Parameters U600 series
        • User Menu: Service Contacts U700 series
  • The Service menu display allows the user to customize the va
    • Service Menu: Unit Diary Log
      • Service Menu: Diagnostics / Service Mode: Page 2 of 5
        • Service Menu: Set Alarm Parameters: Page 2 of 6
        • Service Menu: Set Alarm Parameters: Page 3 of 6
        • Service Menu: Set Alarm Parameters: Page 4 of 6
        • Service Menu: Set Alarm Parameters: Page 5 of 6
        • Service Menu: Set Alarm Parameters: Page 6 of 6
        • Service Menu: Sensor Calibration/ Setup Parameters: Page 2
        • Service Menu: System / Network Setup Parameters Series S800
        • Page 1 of 2, System View
        • Service Menu: System / Network Setup Parameters Series S800
        • Page 2 of 2, System View
        • Service Menu: System / Network Setup Parameters Series S800
        • Page 1 of 2, Unit View
        • Service Menu: System / Network Setup Parameters Series S800
        • Page 2 of 2, Unit View
        • Service Menu: Option Setup Parameters S400 series: Page 1 o
        • Service Menu: Option Setup Parameters S400 series:: Page 2
        • Service Menu: Service Contacts Parameters S700 series:
  • The Advanced menu displays allows the service technician to
    • Advanced Menu: Factory Settings Parameters: Page 4 of 6
      • Large Disdplay
        • Small Display
• P11: Low Pressure Switch Circuits
• P13: DCV Thermistor Signals
• P34: Reheat Devices
• P35: Infrared Humidifier Devices
• P52: Glycool Valve (Opt. Pressure Modulating)
• P53:
• P54:
  • P67: Temperature/ Humidity Sensors
    • P65: Optional Intelleslot Power Suplly
• TB1: 24 VAC
  • E1/ E2/ E3/ E4: Transformer Grounds
    • P4: 24 VAC Power
    • Areas of Control
    • Semiconductor
    • Semiconductor Showing No Movement of Electrons
    • Front and Left Side Views of the Triac
    • Schematic Drawing for the Triac
  • Basic Operation of the Opto-Isolator
    • Output Opto-Isolator
    • Input Opto-Isolator
      • Output Opto-Isolator Pin Location
        • Input Opto-Isolator Pin Location
          • Control Output Triac Legend:
    • Troubleshooting Checklist
      • Agent: A program that performs some information gathering o
        • In computer science, there is a school of thought that belie
          • BOOTP: Short for Bootstrap Protocol, an Internet protocol t
            • Cookie: A message given to a Web browser by a Web server.
              • DHCP: Short for Dynamic Host Configuration Protocol, a prot
                • Ethernet: A local-area network (LAN) architecture developed
                • Internet: A global network connecting millions of computers
                • IP address: An identifier for a computer or device on a TCP
                • Network: A group of two or more computer systems linked tog
                • Network interface card: Often abbreviated as NIC, an expans
                • Protocol: An agreed-upon format for transmitting data betwe
                • SNMP: Short for Simple Network Management Protocol, a set o
                • SNMP 1 reports only whether a device is functioning properly
                • TCP/IP: Abbreviation for Transmission Control Protocol/Inte
                • 10BaseT: One of several adaptations of the Ethernet (IEEE 8
                • Understanding IP Addressing: Every computer that communicat
• cover manual TM-10098 rev 02-06 icom t&s.pdf
  • Environmental Training and Service Manual
    • TM-10098: Rev. 02/06