Document Outline

• Index
• 1316A-3 Multi Gas Monitor
• Safety Considerations
• About this Manual
• Chapter 1 Introduction and Specifications
  • 1.1 Broad Overview
  • 1.2 Monitor System Description
    • 1.2.1 Control Software and PC Interface
    • 1.2.2 NDIR Module and UA1372 Module (Optional) Measuring System
    • 1.2.3 Power Supply
  • 1.3 Software Description
    • 1.3.1 NDIR Module and the optional UA1372 Module Versions
  • 1.4 NDIR Gas Measurement
    • 1.4.1 Ethanol, CO and CO2 Measurement
    • 1.4.2 The Infrared Transmission Spectra.
    • 1.4.3 The NDIR Module Building blocks
    • 1.4.4 The NDIR Temperature Measurements.
    • 1.4.5 The NDIR Pressure Measurements.
    • 1.4.6 The O2 and NO Measurement
• Chapter 2 Installation and Getting Started
  • 2.1 Installing the Monitor
    • 2.1.1 Operating Environment
    • 2.1.2 The Gas Sample Line
    • 2.1.3 Mains Supply
    • 2.1.4 Checking and Changing the Fuses
  • 2.2 The BZ 6014 Software
    • 2.2.1 Computer Requirements
    • 2.2.2 Installing the BZ6014 Software on the PC
    • 2.2.3 Installing the USB driver for the 1316A-3
    • 2.2.4 Verification of the Software BZ6014 Version.
  • 2.3 Connecting the Monitor to the PC
  • 2.4 Starting the Monitor
  • 2.5 Starting the BZ6014 Software
    • 2.5.1 To start the Software
  • 2.6 Using the Software
    • 2.6.1 Screen Layout
    • 2.6.2 Title Bar
    • 2.6.3 Menu Bar
    • 2.6.4 Workspace
    • 2.6.5 Settings
    • 2.6.6 Active Benches
    • 2.6.7 Moving around the Screen
    • 2.6.8 Entering Values
  • 2.7 Selecting the Correct Serial Port
  • 2.8 Starting a Measurement
  • 2.9 Stopping a Measurement Task
• Chapter 3 Configuration and displaying measurement results
  • 3.1 General Information
  • 3.2 Software Configuration
    • 3.2.1 BZ 6014 Main Menu
    • 3.2.2 Description of the Settings in the Main Menu Screen.
    • 3.2.3 Gas Curves
  • 3.3 Status
  • 3.4 Screen Problem Status
    • 3.4.1 Pump in Flow
    • 3.4.2 New NO Sensor
    • 3.4.3 New O2 Sensor
    • 3.4.4 IR signal lost
    • 3.4.5 Pump Out Flow
    • 3.4.6 Ambient Temperature range
    • 3.4.7 Pump Low Flow
    • 3.4.8 Leak Check
  • 3.5 Reset.
  • 3.6 Operating Modes of the Multi Gas Monitor 1316A-3
    • 3.6.1 Start-up Operating Mode
    • 3.6.2 Normal Operating Mode
    • 3.6.3 Standby Operating Mode
    • 3.6.4 System Fault Operating Mode
• Chapter 4 Calibration
  • 4.1 Introduction
    • 4.1.1 Factory calibration
    • 4.1.2 Field Calibration
  • 4.2 Zero Calibration and O2 Span Calibration
    • 4.2.1 Zero Calibration Procedure
    • 4.2.2 Error and Warnings Related to a Zero Calibration
  • 4.3 Span Calibration
    • 4.3.1 Introduction.
    • 4.3.2 Checking and Changing the Particle Filters
    • 4.3.3 Calibration Gases
    • 4.3.4 Connecting the Calibration Gas
    • 4.3.5 Span Calibration
    • 4.3.6 To perform a span calibration with single component gas.
    • 4.3.7 To perform a span calibration with multi component gas mixture.
    • 4.3.8 Installing a new NO sensor.
  • 4.4 Reset Span Calibration
• Chapter 5 Maintenance
  • 5.1 Maintenance Items
    • 5.1.1 Changing Zero Channel inlet filter
    • 5.1.2 Changing the fuses
    • 5.1.3 Checking the Pump
    • 5.1.4 System ID
    • 5.1.5 Valve Test
    • 5.1.6 Miscellaneous Data.
    • 5.1.7 Pressure Data.
    • 5.1.8 O2 and NO Sensor Replacement
    • 5.1.9 Field replaceable parts.