MacDon R85 Rotary Disc 16 Foot Pull-Type Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for R85 Rotary Disc 16 Foot Pull-Type MacDon
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 244 |
| Size: | 12.06 MB |
Show table of contents
Read manual
Document Outline
- toc
- Introduction
- Serial Number(s)
- 1Safety
- 2Definitions
- 3Component Identification
- 4Specifications
- 5Operation
- 5.1Owner/Operator Responsibilities
- 5.2Operational Safety
- 5.3Lift Cylinder Lock-Out Valves
- 5.4Driveshields
- 5.5Cutterbar Doors
- 5.6Daily Start-Up Check
- 5.7Tractor Setup
- 5.8Mower Conditioner/Tractor Hookup
- 5.9Disconnecting the Mower Conditioner from a Tractor
- 5.10Engaging the Power Take-Off (PTO)
- 5.11Raising and Lowering the Mower Conditioner
- 5.12Break-in Period
- 5.13Leaving the Tractor
- 5.14Maneuvering/Steering the Mower Conditioner
- 6Transporting the Mower Conditioner
- 7Operating the Mower Conditioner
- 7.1Float
- 7.2Roll Gap
- 7.3Roll Tension
- 7.4Roll Timing
- 7.5Forming Shields
- 7.6Mower Conditioner Angle
- 7.7Cutting Height
- 7.8Ground Speed
- 7.9Tall Crop Feed Plates
- 7.10Tall Crop Dividers
- 7.11The Overshot Auger
- 7.12Stripper Bars
- 7.13Haying Tips
- 7.14Levelling the Mower Conditioner
- 7.15Unplugging the Mower Conditioner
- 8Maintenance and Servicing
- 8.1Preparation for Servicing
- 8.2Recommended Safety Procedures
- 8.3Torque Specifications
- 8.4Conversion Chart
- 8.5Recommended Lubricants
- 8.6Maintenance Requirements
- 8.7Cutterbar Disc Maintenance
- 8.8Drive Systems
- 8.9Hydraulics
- 8.10Electrical
- 8.11Wheels and Tires
- 9Troubleshooting
- 10Options and Attachments
- Introduction
- tables
- Table 5.1 Drawbar specifications
- Table 6.1 Lifting vehicle specifications
- Table 6.2 Chain specifications
- Table 6.3 Lifting vehicle specifications
- Table 6.4 Chain specifications
- Table 8.1 SAE Grade 5 Bolt and Grade 5 Free Spinning
- Table 8.2 SAE Grade 5 Bolt and Grade 5 Distorted Thread Nut
- Table 8.3 SAE Grade 8 Bolt and Grade 8 Distorted Thread Nut
- Table 8.4 SAE Grade 8 Bolt and Grade 8 Free SpinningNut
- Table 8.5 Metric Class 8.8 Bolts and Class 9 Free Spinning Nut
- Table 8.6 Metric Class 8.8 Bolts and Class 9 Distorted Thread Nut
- Table 8.7 Metric Class 10.9 Bolts and Class 10 Free Spinning Nut
- Table 8.8 Metric Class 10.9 Bolts and Class 10 Distorted Thread Nut
- Table 8.9 Metric Bolt Bolting into Cast Aluminum
- Table 8.10 Flare-type hydraulic tube fittings
- Table 8.11 O-Ring Boss (ORB) Hydraulic Fittings (Adjustable)
- Table 8.12 O-Ring Face Seal (ORFS) Hydraulic Fittings