Document Outline

• TABLE OF CONTENTS
• SECTION 1. APPLICATION MESSAGES
  • OVERVIEW
  • MESSAGE FORMAT
    • Message Header
    • Data Field
• SECTION 2. GENERIC COMMANDS
  • GET PROPERTY COMMAND
  • SET PROPERTY COMMAND
  • SAVE PROPERTY COMMAND
• SECTION 3. DEVICE APPLICATION
  • GET/SET/SAVE PROPERTY COMMANDS
  • MODEL NUMBER PROPERTY
  • SOFTWARE ID PROPERTY
  • SOFTWARE RESET COMMAND
• SECTION 4. MAGNETIC STRIPE APPLICATION
  • GET/SET/SAVE PROPERTY COMMANDS
  • NOTIFY READ STATE PROPERTY
  • NOTIFY READ TRACK PROPERTY
  • DECODE JIS TYPE 2 PROPERTY
  • CLEAR DATA COMMAND
  • GET TRACK 123 DECODE DATA COMMAND
  • GET TRACK DECODE DATA COMMAND
  • GET MAGNEPRINT DATA COMMAND
• SECTION 5. SMART CARD APPLICATION
  • GET/SET/SAVE PROPERTY COMMANDS
  • RESPONSE CODES USED THROUGHOUT THE APPLICATION
  • NOTIFICATIONS IN THE SMART CARD APPLICATION
    • Request/Response/Notification Model
    • Example Request/Response/Notification Sequence
  • THE CONDRPT PROPERTY
  • ERROR/WARNING CONDITION TEMPLATES
  • CARD TYPES
  • PROPERTIES
  • ATR MAP STRUCTURE – MICROPROCESSOR CARDS ONLY
  • POWER UP COMMAND
  • POWER DOWN COMMAND
  • T=0 ERROR / WARNING CONDITION TEMPLATES
  • T=1 ERROR / WARNING CONDITION TEMPLATES
  • WARM RESET COMMAND
  • TPDU, CARD TO IFD COMMAND
  • TPDU, IFD TO CARD COMMAND
  • APDU EXCHANGE COMMAND
  • SELECT CONNECTOR COMMAND
• SECTION 6. LED APPLICATION
  • GET/SET/SAVE PROPERTY COMMANDS
  • LED STATE PROPERTY
• SECTION 7. TRANSPORT APPLICATION
  • GET/SET/SAVE PROPERTY COMMANDS
  • INDICATORS PROPERTY
  • NOTIFY INDICATOR CHANGE 0 TO 1 PROPERTY
  • NOTIFY INDICATOR CHANGE 1 TO 0 PROPERTY
  • AUTO CONSUME PROPERTY
  • MSR DIRECTION PROPERTY
  • EJECT MIDDLE SENSOR TO MOTOR OFF DELAY PROPERTY
  • POWER FAIL DETECT PROPERTY
  • CONSUME CARD COMMAND
  • EJECT CARD COMMAND
• SECTION 8. BUZZER APPLICATION
  • GET/SET/SAVE PROPERTY COMMANDS
  • TONE SEQUENCE 1 PROPERTY
  • TONE SEQUENCE 2 PROPERTY
  • TONE SEQUENCE 3 PROPERTY
  • TONE SEQUENCE 4 PROPERTY
  • PLAYBACK TONE SEQUENCE COMMAND
• SECTION 9. HOST COMMUNICATIONS APPLICATION
  • GET/SET/SAVE PROPERTY COMMANDS
  • USB SERIAL NUMBER PROPERTY
  • RS232 PLUG AND PLAY SUPPORT ENABLE PROPERTY
  • USB PRODUCT PROPERTY
  • MCP ERROR RECOVERY ENABLE PROPERTY
  • MCP EDC CHECK ENABLE PROPERTY
  • MCP AUTO BAUD ENABLE PROPERTY
  • FIXED BAUD RATE PROPERTY
  • RESET DETECTED PROPERTY
  • PROTOCOL PROPERTY
• SECTION 10. OTI SCI 1000 CONTACTLESS SMART CARD APPLICATION
  • GET/SET/SAVE PROPERTY COMMANDS
  • NOTIFY CONTACTLESS MAGSTRIPE PROPERTY
  • CONTACTLESS AUTOMATIC RF CONTROL PROPERTY
    • Auto Mode
    • Example Notification Sequence
    • RF ON Command
  • RF OFF COMMAND
  • SENDING OTI MODULE TRANSPARENT COMMANDS
• APPENDIX A. EXAMPLE HOST APPLICATION
• APPENDIX B. MEMORY CARD SUPPORT
  • SLE 4442/4432 MEMORY CARD CONTROL
    • Properties
    • Power Up
    • APDU Exchange Command
    • Read Binary APDUl:
    • Update Binary APDU
    • Verify APDU (Programmable Security Code)
  • SLE 4428/4418 MEMORY CARD CONTROL
    • Properties
    • Power Up
    • APDU Exchange Command
    • Read Binary APDU
    • Read Protection Status APDU
    • Update Binary APDU
    • Update Binary With Protection APDU
    • Verify APDU (Programmable Security Code)
  • SLE 4404 MEMORY CARD CONTROL
    • Properties
    • Power Up
    • APDU Exchange Command
    • Special handling for C4 and RST
    • Read Binary APDU
    • Write Binary APDU
    • Erase Binary APDU
    • Verify/Erase Application Zone APDU
  • I2C( MEMORY CARD CONTROL
    • Properties
    • Power Up
    • APDU Exchange Command
    • Read Binary APDU
    • Update Binary APDU
  • GEMPLUS GAM326 MEMORY CARD CONTROL
    • Properties
    • Power Up
    • APDU Exchange Command
    • Read Binary APDU
    • Write Binary APDU
    • Erase Counter APDU
    • Internal Authenticate APDU
• APPENDIX C. MIFARE COMMANDS
• INDEX