Document Outline

• Table of Contents
  • IMPORTANT SAFETY INSTRUCTIONS
    • FCC Requirements
    • Canadian Department of Communications Statement
  • Chapter 1: Introduction
    • Technical Support
  • Chapter 2: Installation
    • 2.1 Operating Environment
    • 2.2 Mounting
    • 2.3 Power Surge Protection
    • 2.4 Power Supply and Battery Backup
    • 2.5 Starting the OMA-P1104
    • 2.6 Run Mode and Standby Mode
    • 2.7 Telephone Line
    • 2.8 The Microphone
    • 2.9 Alert Inputs
    • 2.10 Installing the Sensor
    • 2.11 Multiple Sensors
    • 2.12 Outdoor Wiring
    • 2.13 Disconnecting for Storage or Seasonal Use.
  • Chapter 3: Quick Start
    • 3.1 The Local Keypad
    • 3.2 Preparation for Programming
    • 3.3 Quick-Start Programming Steps
      • Step 2: Set the ID Number
      • Step 3: Set Dial-Out Telephone Numbers
      • Step 4: Set Temperature Limits
    • 3.4 Summary of the Alarm Dial-Out Process
  • Chapter 4: Communications Programming
    • 4.1 The Unit ID Number
      • 4.1.1 Programming the ID Number
      • 4.1.2 Interrogating the ID Number
    • 4.2 Dial-out Telephone Numbers
      • 4.2.1 Programming Dial-out Telephone Numbers
      • 4.2.2 Interrogating a Dial-out Telephone Number
      • 4.2.3 Erasing a Telephone Number
    • 4.3 Tone or Pulse Dialing
    • 4.4 Special Dialing
      • 4.4.1 Special Dialing Keys
      • 4.4.2 Incorporating a Pause
      • 4.4.3 Incorporating a Pound (#) or Asterisk (*)
      • 4.4.4 Special Dialing to a Beeper or Pager
    • 4.5 Rings Until Answer
      • 4.5.1 Programming Rings Until Answer
      • 4.5.2 Interrogating Rings Until Answer
    • 4.6 TAD (Telephone Answering Device)
      • 4.6.1 TAD Enable/Disable
      • 4.6.2 Using the TAD Feature
      • 4.6.3 No TAD In Use
    • 4.7 Listen-in Time
      • 4.7.1 Programming the Listen-in Time
      • 4.7.2 Interrogating the Listen-in Time
    • 4.8 Call Delay
      • 4.8.1 Programming the Call Delay
      • 4.8.2 Interrogating Call Delay
    • 4.9 Local Voice Mute
      • 4.9.1 Enable/Disable Local Voice Mute
    • 4.10 Voice Repetitions
      • 4.10.1 Programming Voice Repetitions
      • 4.10.2 Interrogating Voice Repetitions
    • 4.11 Intercall Time
      • 4.11.1 Programming Intercall Time
      • 4.11.2 Interrogating Intercall Time
    • 4.12 Maximum Number of Calls (Max Calls)
      • 4.12.1 Programming Max Calls
      • 4.12.2 Interrogating Max Calls
    • 4.13 The Clock
      • 4.13.1 Setting the Clock
      • 4.13.2 Interrogating for the Current Time
    • 4.14 The Security Code
      • 4.14.1 Locking the Keypad
      • 4.14.2 Unlocking the Keypad
  • Chapter 5: Alarm Programming
    • 5.1 Input Configuration
      • 5.1.2 Verifying Input Configuration
    • 5.2 Enable/Disable Inputs
      • 5.2.1 Changing Enabled/Disabled Input Status
      • 5.2.2 Verifying Enabled/Disabled Input Status
    • 5.3 Input Recognition Time
      • 5.3.1 Programming Input Recognition Time
      • 5.3.2 Interrogating Input Recognition Time
    • 5.4 Establishing High and Low Temperature Limits
      • 5.4.1 Programming Temperature Limits for a
      • 5.4.2 Disabling Alarm Response to High or Low Temperature
      • 5.4.3 Interrogating High and Low Temperature Limits
    • 5.5 Temperature Scale
    • 5.6 Temperature Calibration
      • 5.6.1 Programming Temperature Calibration
      • 5.6.2 Interrogating Temperature Calibration
    • 5.7 Obtaining Current Temperature
    • 5.8 AC Power Monitoring Enable/Disable
      • 5.8.1 Enabling/Disabling the AC Power Alarm
    • 5.9 AC Power Failure Recognition Time
      • 5.9.1 Programming Power Failure Recognition Time
      • 5.9.2 Interrogating Power Failure Recognition Time
    • 5.10 Sound Alarm Monitoring
      • 5.10.1 Programming Sound Alarm Sensitivity
      • 5.10.2 Interrogating Sound Sensitivity
      • 5.10.3 Programming High Sound Alarm Recognition Time
    • 5.11 High Sound Alarm Enable/Disable
      • 5.11.1 Changing Enabled/Disabled High Sound Alarm
    • 5.12 Exit Delay
  • Chapter 6: Acknowledgment, Status Report, and Remote Access
    • 6.1 Alarm Acknowledgment
      • 6.1.1 Local Acknowledgment
      • 6.1.2 Touch-ToneTM Acknowledgment
      • 6.1.3 Callback Acknowledgment
    • 6.2 Status Report
      • 6.2.1 Example: Status Report, No Alarms
      • 6.2.2 Example: Status Report, Existing Alarms
      • 6.2.3 Example: Status Report, Disabled Inputs
      • 6.2.4 Battery Condition
      • 6.2.5 Remote Access by Touch-Tone™ Telephone
  • Appendix A: Troubleshooting
  • Appendix B: Accessories 87