Document Outline

• Powerware 9315 UPS 200-300 kVA Operation Manual
• Table of Contents
• List of Figures
• Chapter 1 Introduction
  • 1.1 Conventions Used in This Manual
  • 1.2 For More Information
  • 1.3 Getting Help
• Chapter 2 Getting Started
  • 2.1 Safety Warnings
  • 2.2 Typical Powerware 9315 UPS System
  • 2.3 Looking Inside the UPS
  • 2.4 UPS Standard Features
    • 2.4.1 Monitor Panel
    • 2.4.2 Control Panel
    • 2.4.3 Communication Bays
    • 2.4.4 Input Filter
    • 2.4.5 Emergency Load Off
    • 2.4.6 Automatic Battery Charge Current Limit
    • 2.4.7 Installation Features
  • 2.5 Options and Accessories
    • 2.5.1 Battery
    • 2.5.2 External Battery Disconnect
    • 2.5.3 Power Distribution Module (LV models only)
    • 2.5.4 Upgrade Capability
    • 2.5.5 Remote Monitor Panel
    • 2.5.6 Relay Interface Module
    • 2.5.7 Input Isolation Transformer
    • 2.5.8 5% Input Filter
    • 2.5.9 Output Transformer
    • 2.5.10 Modem
    • 2.5.11 Customer Convenience Outlet
  • 2.6 Symbols, Controls, and Indicators
• Chapter 3 Understanding UPS Operation
  • 3.1 Normal Mode
  • 3.2 Bypass Mode
  • 3.3 Battery Mode
  • 3.4 Monitoring and Controlling UPS Operation
• Chapter 4 Starting and Stopping the UPS
  • 4.1 Using the Control Panel
    • 4.1.1 To Place the UPS in Normal Mode
    • 4.1.2 To Shut Down the UPS from Normal Mode
    • 4.1.3 To Start the UPS in Bypass Mode
    • 4.1.4 To Shut Down Power to the Critical Load While in Bypass Mode
• Chapter 5 Using the Monitor Panel
  • 5.1 Using the LCD Screen
  • 5.2 Using the Buttons
  • 5.3 Adjusting the Contrast
  • 5.4 Using the Load Off Button
  • 5.5 Reading the Status Indicators
  • 5.6 Using the Menu Options
• Chapter 6 Using Features and Options
  • 6.1 Building Alarm Monitoring
  • 6.2 Summary Alarm Contacts
  • 6.3 Remote Monitor Panel
  • 6.4 Battery Cabinets
  • 6.5 External Battery Disconnect
  • 6.6 Relay Interface Module
  • 6.7 Supervisory Contact Module
• Chapter 7Communication
  • 7.1 Locating the Communication Bays
  • 7.2 X-Slot Cards
  • 7.3 LanSafe Power Management Software
  • 7.4 Connecting Equipment to a Serial Port
  • 7.5 Configuring the Serial Ports
    • 7.5.1 Mode
    • 7.5.2 Rate
    • 7.5.3 Data/Stop
    • 7.5.4 Handshaking
    • 7.5.5 Save
    • 7.5.6 Default Settings
  • 7.6 Terminal Mode
    • 7.6.1 Printing Selected Information
    • 7.6.2 Entire Log - [Ctrl]+[P]
    • 7.6.3 Meters Printout - [Ctrl]+[M]
    • 7.6.4 System Information Printout - [Ctrl]+[A]
    • 7.6.5 Battery Test Printout - [Ctrl]+[B]
  • 7.7 System Configuration
    • 7.7.1 System Configuration Mode Main Menu
    • 7.7.2 Program Building Alarms
    • 7.7.3 Enable/Disable Default Functions
    • 7.7.4 Customize Alarm Messages
    • 7.7.5 Program Unit Name
    • 7.7.6 Adjust Output Voltage
    • 7.7.7 Change Password
    • 7.7.8 Battery Test Setup
    • 7.7.9 Modify Low Battery Time
  • 7.8 Calibration Mode
  • 7.9 Computer Mode
  • 7.10 Remote Monitor Mode
  • 7.11 Remote Notification
• Chapter 8 Maintaining the UPS System
  • 8.1 Important Safety Instructions
  • 8.2 Performing Preventive Maintenance
  • 8.3 Maintenance Training
• Chapter 9 Product Specifications
• Chapter 10Responding to System Events
  • 10.1 System Event Horns
  • 10.2 System Event Lights
  • 10.3 System Event Messages
• Chapter 11 Using the LOAD OFF Button
  • 11.1 Using the LOAD OFF Button
  • 11.2 Resetting the UPS System after Load Off
• Warranty
• Manual Part Number and Revision