Document Outline

• 1. INTENDED USE
• 2. PRECAUTIONS
  • 2.1. Maintenance
  • 2.2. Accumulator / battery pack
    • 2.2.1. Power supply of weighing indicators in plastic casings
    • 2.2.2. Replacement of worn batteries
  • 2.3. Operation in a strong electrostatic field
• 3. WARRANTY CONDITIONS
• 4. MAIN DIMENSIONS
• 5. GETTING STARTED
• 6. KEYPAD
• 7. KEYS’ FUNCTIONS
• 8. INSCRIPTIONS ON THE DISPLAY
• 9. USER MENU
  • 9.1. Submenus
  • 9.2. Browsing user menu
    • 9.2.1. Keypad
    • 9.2.2. Return to the weighing mode
• 10. WEIGHING
  • 10.1. Tarring
  • 10.2. Inscribing tare value
  • 10.3. Zeroing
  • 10.4. Weighings in two ranges
  • 10.5. Selection of basic weight unit
  • 10.6. Temporarily selected unit
• 11. MAIN PARAMETERS
  • 11.1. Setting a filtering level
  • 11.2. Median filter
  • 11.3. Autozero function
  • 11.4. Tare function
• 12. RS 232 PARAMETERS
  • 12.1. Printout type
  • 12.2. Minimal mass threshold
  • 12.3. Baud rate
  • 12.4. Serial transmission parameters
• 13. OTHER PARAMETERS
  • 13.1. Backlight function
    • 13.1.1. Backlight for supplying from mains
    • 13.1.2. Backlight for supplying from batteries
  • 13.2. “Beep” signal – after pressing a key
  • 13.3. Automatic switch-off
  • 13.4. Battery voltage level check
    • 13.4.1. Checking the batteries
    • 13.4.2. Battery discharge pictogram
    • 13.4.3. Accumulator charging option
    • 13.4.4. Formatting rechargeable battery packs
• 14. WORK MODES
  • 14.1. Setting accessibility of operation modes
  • 14.2. Selecting quantity of operation modes
  • 14.3. Counting pieces of the same mass
  • 14.4. +/- control referring to the inscribed standard mass
  • 14.5. Control of % deviation referring to the inscribed standard mass
    • 14.5.1. Standard mass determined by its weighing
    • 14.5.2. Mass of standard inscribed to scale memory
  • 14.6. Automatic tare
  • 14.7. Measurement max force on the pan – latch
  • 14.8. Totalizing
    • 14.8.1. Enabling the work mode
    • 14.8.2. Totalizing procedure
    • 14.8.3. Memory of the last value of sum of weighed goods
    • 14.8.4. Return to weighing
  • 14.9. Weighing animals
  • 14.10. Tare memory
    • 14.10.1. Entering the tare value to the scale memory
    • 14.10.2. Selecting a tare value from the memory
• 15. USER CALIBRATION
  • 15.1. Calibration
  • 15.2. Start mass adjustment
• 16. COOPERATION WITH PRINTER
• 17. COOPERATION WITH COMPUTER
• 18. COMMUNICATION PROTOCOL
  • 18.1. General information
  • 18.2. A set of commands for RS interfaces
  • 18.3. Respond message format
  • 18.4. Command’s description
    • 18.4.1. Zeroing
    • 18.4.2. Tarring
    • 18.4.3. Get tare value
    • 18.4.4. Send the stable result in basic unit
    • 18.4.5. Send the result immediately in basic unit
    • 18.4.6. Send the stable result in current unit
    • 18.4.7. Send the result immediately in current unit
    • 18.4.8. Switch on continuous transmission in basic unit
    • 18.4.9. Switch off continuous transmission in basic unit
    • 18.4.10. Switch on continuous transmission in current unit
    • 18.4.11. Switch off continuous transmission in current unit
    • 18.4.12. Send all implemented commands
  • 18.5. Manual printouts / automatic printouts
  • 18.6. Continuous transmission
  • 18.7. Configuring printouts
• 19. ERROR COMMANDS
• 20. TROUBLE SHOOTING
• 21. TECHNICAL PARAMETERS
  • 21.1. Metrological parameters
  • 21.2. Ambient conditions
  • 21.3. Power supply
• 22. ADDITIONAL EQUIPMENT