Document Outline

• Introduction
• IMPORTANT
• Precautions for Safety
• DEFINITION OF SIGNAL WORDS
• Contents
• Section 1 Overview
  • 1.1 Warnings
  • 1.2 Environmental Conditions
  • 1.3 Components
• Section 2 E8 Emulator Functions
  • 2.1 Overview
  • 2.2 Trace Functions
  • 2.3 Break Functions
  • 2.4 Memory Access Functions
  • 2.5 Stack Trace Function
  • 2.6 Online Help
• Section 3 Preparation before Use
  • 3.1 Emulator Preparation
  • 3.2 Emulator Hardware Configuration
  • 3.3 Emulator Software Configuration
    • 3.3.1 CD
  • 3.4 Installing Emulator’s Debugger
  • 3.5 Connecting the Emulator to the Host Computer
  • 3.6 Connecting the Emulator to the User System
  • 3.7 Connecting System Ground
  • 3.8 System Check
  • 3.9 Uninstalling the Emulator’s Debugger
• Section 4 Preparations for Debugging
  • 4.1 Method for Activating High-performance Embedded Workshop
    • 4.1.1 Creating the New Workspace (Toolchain Not Used)
    • 4.1.2 Creating the New Workspace (Toolchain Used)
    • 4.1.3 Selecting an Existing Workspace
  • 4.2 Setting at E8 Emulator Activation
    • 4.2.1 Setting at Emulator Activation
    • 4.2.2 Downloading a Program
    • 4.2.3 Setting the Writing Flash Memory Mode
• Section 5 Debugging
  • 5.1 Setting the Environment for Emulation
    • 5.1.1 Opening the [Configuration] Dialog Box
    • 5.1.2 [General] Page
  • 5.2 Downloading a Program
    • 5.2.1 Downloading a Program
    • 5.2.2 Viewing the Source Code
  • 5.3 Stopping Your Program
    • 5.3.1 Address Interrupt Breakpoints
  • 5.4 Using the Event Points
    • 5.4.1 PC Breakpoints
    • 5.4.2 Break Conditions
    • 5.4.3 Opening the [Event] Window
    • 5.4.4 Setting PC Breakpoints
    • 5.4.5 Add
    • 5.4.6 Edit
    • 5.4.7 Enable
    • 5.4.8 Disable
    • 5.4.9 Delete
    • 5.4.10 Delete All
    • 5.4.11 Go to Source
    • 5.4.12 [Set Break] Dialog Box
    • 5.4.13 Setting Break Conditions
    • 5.4.14 Edit...
    • 5.4.15 Enable
    • 5.4.16 Disable
    • 5.4.17 Delete
    • 5.4.18 Delete All
    • 5.4.19 Go to Source
    • 5.4.20 Sequential Conditions
    • 5.4.21 Editing Break Conditions
    • 5.4.22 Modifying Break Conditions
    • 5.4.23 Enabling Break Conditions
    • 5.4.24 Disabling Break Conditions
    • 5.4.25 Deleting Break Conditions
    • 5.4.26 Deleting All Break Conditions
    • 5.4.27 Viewing the Source Line for Break Conditions
    • 5.4.28 [Break condition x] Dialog Box
  • 5.5 Viewing the Trace Information
    • 5.5.1 Opening the [Trace] Window
    • 5.5.2 Acquiring Trace Information
    • 5.5.3 Clearing the Trace Information
    • 5.5.4 Saving the Trace Information in a File
    • 5.5.5 Viewing the [Source] Window
    • 5.5.6 Trimming the Source
  • 5.6 Using the Start/Stop Function
    • 5.6.1 Opening the [Start/Stop Function Setting] Dialog Box
    • 5.6.2 Specifying the Routine to be Executed
    • 5.6.3 Restrictions on the Start/Stop Function
• Section 6 Tutorial
  • 6.1 Introduction
  • 6.2 Running the High-performance Embedded Workshop
  • 6.3 Setting up the E8 Emulator
  • 6.4 Setting the [Configuration] Dialog Box
  • 6.5 Checking the Operation of RAM
  • 6.6 Downloading the Tutorial Program
    • 6.6.1 Downloading the Tutorial Program
    • 6.6.2 Displaying the Source Program
  • 6.7 Setting a PC Breakpoint
  • 6.8 Setting Registers
  • 6.9 Executing the Program
  • 6.10 Reviewing Breakpoints
  • 6.11 Viewing Memory
  • 6.12 Watching Variables
  • 6.13 Stepping Through a Program
    • 6.13.1 Executing [Step In] Command
    • 6.13.2 Executing [Step Out] Command
    • 6.13.3 Executing [Step Over] Command
  • 6.14 Forced Breaking of Program Executions
  • 6.15 Displaying Local Variables
  • 6.16 Break Function
    • 6.16.1 PC Break Function
  • 6.17 Hardware Break Function
  • 6.18 Trace Functions
    • 6.18.1 Displaying the Trace Window
  • 6.19 Stack Trace Function
  • 6.20 What Next?
• Appendix A Components of the E8 Emulator
• Appendix B Window Functions
• Appendix C Command-Line Functions
• Appendix D Notes on High-performance Embedded Workshop
• Appendix E Diagnostic Hardware Program
  • E.1. System Setup to Execute the Check Program
  • E.2. Executing the Check Program
  • E.3 When an Error Occurs