Document Outline

• TURBO 96
• OPERATOR’S MANUAL
  • RHINO®
• To the Owner/Operator/Dealer
• DEALER to CUSTOMER Pre-Delivery / Operation Instructions
  • ROTARY MOWER
• Table of Contents
  • GENERAL SAFETY INSTRUCTIONS AND PRACTICES
  • OPERATOR SAFETY
  • CONNECTION OR DISCONNECTING IMPLEMENT SAFETY
  • CRUSHING HAZARDS
  • THROWN OBJECT HAZARDS
    • 1. MARK objects that cannot removed.
    • 2. AVOID these objects when mowing.
      • 1. MAINTAIN MOWER SHIELDING, side skirts, skid shoes, and blades in good operational condition,
      • 2. RAISE CUTTING HEIGHT to 6 INCHES minimum,
      • 3. INSPECT AREA thoroughly before mowing to REMOVE potential THROWN OBJECT HAZARDS,
      • 4. NEVER ALLOW BLADES to CONTACT SOLID OBJECTS like wire, rocks, post, curbs, guardrails, or ground while mowing. PN TO02
    • 1. BLADES CAN FAIL from impact and objects can be thrown with great velocity.
    • 2. INSPECT and REPLACE any damaged blades.
    • 3. CHECK blade carrier and REPLACE if damaged.
      • 1. STOP PTO and back up mower.
      • 2. LOWER mower, engage PTO and mow forward.
  • RUN OVER HAZARDS
  • PTO ENTANGLEMENT HAZARDS
  • MOWER BLADE CONTACT HAZARDS
  • HIGH PRESSURE OILLEAK HAZARDS
  • ELECTRICAL & FIRE HAZARDS
  • TRANSPORTING HAZARDS
  • HAZARDS WITH MAINTENANCE OF IMPLEMENT
  • PARTS INFORMATION
  • Decal Location - Lift Type
    • 1. D389 1 DECAL Multi Hazard
    • 2. D388 1 DECAL Driveline Hazards
    • 3. 00756004 3 DANGER Shield Missing. Do Not Operate
    • 4. 00756005 2** DANGER Rotating D/L Entanglement
    • 5. D137 1 INSTRUCT CCW Blade Rotation, Blade Bolt Torque
    • 6. D138 1 INSTRUCT CW Blade Rotation, Blade Bolt Torque
    • 7. D454 1 WARNING Crushing Hazard (Decal under Deck)
    • 8. 00771283 3 INFORMATION 5 Year Gearbox Warranty
    • 9. 00778950 1 INFORMATION Patented
    • 10. 99102 1 LOGO Rhino
    • 11. D303 2 NAME Rhino Type (4-3/8 x 16-3/4)
    • 12. 00785579 2 NAME Turbo 96
    • 13. 00785578 1 NAME Turbo 96
    • 14. D302 2 LOGO Rhino Logo (4-7/8 x 6-1/2)
    • 15. 03200347 * REFLECTOR SMV Sign
    • 16. 00760657 1 IMPORTANT Rhino Genuine Parts, Rotary Mower
    • 17. nfs 1 SER PLT Serial Number Plate
    • 18. D401 1 INSTRUCT 1000 RPM
    • 19. 1458392 2 REFLECTOR Red Reflectors
    • 20. 1458393 2 REFLECTOR Amber Reflectors
    • 21. 00776031 1 ___________ Canister, Operator’s Manual
    • 22. 00778586C 1 ___________ Operator’s Manual
    • 23. 10058000 3 ___________ Bolt
    • 24. 00024100 6 ___________ Flatwasher
    • 25. 02959924 3 ___________ Locknut
    • 26. 00785538 1 LOGO Turbo Dome Deck
    • 27. D614 2 DANGER Thrown Object Shield Missing
    • 28. D534 2 WARNING Blade Bolt Torque
    • 29. D629 1 INSTRUCT Lubrication
    • 30. D608 2 WARNING Blade Timing
  • Decal Location - Pull Type
    • 1. D389 1 DECAL Multi Hazard
    • 2. D388 1 DECAL Driveline Hazards
    • 3. 00756004 3 DANGER D/L Shield Missing. Do Not Operate
    • 4. 00756005 2** DANGER Rotating D/L Entanglement
    • 5. D137 1 INSTRUCT CCW Blade Rotation
    • 6. D138 1 INSTRUCT CW Blade Rotation
    • 7. D454 1 WARNING Crushing Hazard (Decal under Deck)
    • 8. 00771283 3 INFORMATION 5 Year Gearbox Warranty
    • 9. 00778950 1 INFORMATION Patented
    • 10. 99102 1 LOGO Rhino
    • 11. D303 2 NAME Rhino Type (4-3/8 x 16-3/4)
    • 12. 00785579 2 NAME Turbo 96 (Large)
    • 13. 00785578 1 NAME Turbo 96 (Small)
    • 14. D302 2 LOGO Rhino Logo (4-7/8 x 6-1/2)
    • 15. 03200347 * REFLECTOR SMV Sign
    • 16. 00760657 1 IMPORTANT Rhino Genuine Parts
    • 17. nfs 1 SER PLT Serial Number Plate
    • 18. D401 1 INSTRUCT 1000 RPM
    • 19. 1458392 2 REFLECTOR Red Reflectors
    • 20. 1458393 2 REFLECTOR Amber Reflectors
    • 21. 00776031 1 ___________ Canister, Operator’s Manual
    • 22. 00778586C 1 ___________ Operator’s Manual
    • 23. 10058000 3 ___________ Bolt
    • 24. 00024100 6 ___________ Flatwasher
    • 25. 02959924 3 ___________ Locknut
    • 26. 00785538 1 INFORMATION Turbo Dome Deck
    • 27. D614 2 DANGER Thrown Object Shield Missing
    • 28. D534 2 WARNING Blade Bolt Torque
    • 29. D629 1 INSTRUCT Lubrication
    • 30. D608 2 WARNING Blade Timing
    • 31. D390 1 DECAL Pull Type Unit Hazards
    • 32. D518 1 WARNING Jack Positioning
  • Decal Description
    • Federal Laws and Regulations
      • SAFETY SECTION
    • EQUIPMENT SPECIFICATIONS
  • KEY OPERATION POINTS
    • Operating Noise Level/Sound Pressure
    • Warranty Information
  • RHINO LIMITED WARRANTY
    • 1. LIMITED WARRANTIES
    • 1.01. Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the ...
    • 1.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.
    • 1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, ...
    • 1.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.
    • 2. REMEDIES AND PROCEDURES.
    • 2.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase.
    • 2.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based
    • 2.03. Purchaser is responsible for returning the goods in question to the Dealer.
    • 2.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will:
    • 2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for...
    • 3. LIMITATION OF LIABILITY.
    • 3.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
    • 3.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS.
    • 3.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLU...
    • 3.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.
    • 4. MISCELLANEOUS.
    • 4.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.
    • 4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term.
    • 4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.
    • 4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
      • INTRODUCTION SECTION
    • DEALER SET-UP INSTRUCTIONS
    • A-FRAME ASSEMBLY-LIFT TYPE
      • 1. Insert bushing (15) into lower end of each A-Frame half (1 & 2). Position each A-Frame half inside Mainframe Lug. Install bolt (19) with Flatwasher (20) through bushing (15) in A-Frame half (1 & 2) and hole in inside Mainframe lug. Install locknut...
      • 2. Install bushing (6) between braces (3) through top rear hole of A-Frame and insert bolt (12), flatwasher (20) and locknut (10). Install Driveline Holder Bracket (22) to left A-Frame (2) with bolt (17) and locknut (18).
      • 3. Install bushing (21) between A-Frame halves (1 & 2) and insert bolt (13) and locknut (14). Then attach braces (3) and brace (7) by installing bushings (15) through brace (7), and install bolt (9) and locknut (10) through braces (3) and brace (7). ...
      • 4. Install brace support (7) to the rear lugs on the Mainframe with pivot pin (8) and retain with bolt (17) and locknut (10). FIGURE Asm-R-0282
    • TAILWHEEL ASSEMBLY - LIFT
    • TONGUE
    • AXLE ASSEMBLY - PULL TYPE
    • AXLE ARMS
  • AXLE ASSEMBLY - HYDRAULIC OFFSET & SEMI-MOUNT
    • CONTROL RODS - PULL TYPE
    • DRIVELINE CLAMP CONE YOKE
    • WHEELS
  • FRONT AND REAR DEFLECTORS (Standard Equipment)
    • Front Deflector
    • Rear Deflector
  • CHAINGUARDS (Optional Equipment at Extra Cost)
    • Front Chainguard
    • Rear Chainguard
  • DRIVELINE ATTACHMENT
    • SHIELD ASSEMBLY - Side Drives - Lift and Pull
    • SHIELD ASSEMBLY - Main Input - Lift and Pull
  • CHECK CHAINS (Extra Equipment) LIFT MODELS
    • JACKSHAFT BEARING SUPPORT ASSEMBLY
  • HYDRAULIC OR MANUAL LIFT - PULL & OFFSET TYPE
    • CASTER WHEEL ASSEMBLY (Semi-Mount)
      • ASSEMBLY SECTION
      • OPERATION SECTION
• RHINO TURBO 96 MEDIUM-DUTY ROTARY MOWER
• OPERATION INSTRUCTIONS
  • 1. OPERATOR REQUIREMENTS
  • 2. TRACTOR REQUIREMENTS
    • Tractor Requirements and Capabilities
    • 2.1 ROPS and Seat Belt
    • 2.2 Tractor Safety Devices
    • 2.3 Tractor Horsepower
    • 2.4 3-Point Hitch
    • 2.5 Drawbar-Pull Type Mower
    • 2.6 Front End Weight
    • 2.7 Power Take Off (PTO)
    • 2.8 Tire Spacing
    • 3. GETTING ON AND OFF THE TRACTOR
      • 3.1 Boarding the Tractor
      • 3.2 Dismounting the Tractor
    • 4. STARTING THE TRACTOR
    • 5. CONNECTING THE MOWER TO THE TRACTOR
      • 5.1 Connecting the Mower - Lift Type and Semi-Mount Type
        • 1. Make sure the tractor is equipped with the correct PTO shaft. Change shafts if needed.
        • 2. Shorten or remove the tractor drawbar to avoid interference when raising and lowering the mower.
        • 3. Board the tractor and start the engine. Position the tractor to the mower with the 3-point lift arms positioned between the respective set of mower A-frame lift lugs.
        • 4. Turn off the tractor engine, set the parking brake, place the tractor in park, and dismount.
        • 5. One lift arm at a time, align arm end hole between the set of holes of A-frame lift lugs. Insert hitch pin through the lug and arm holes and insert retaining pin into hitch pin. Walk around to opposite side and repeat procedure for remaining lift ...
        • 6. Lift Mowers-Extend or retract the 3-point top link to align its end hole with the holes of the mower’s top link. Insert the top link hitch pin and insert retaining pin into hitch pin. Semi-Mount Mowers-If hydraulic cylinders are being used to ra...
        • 7. Adjust any lower link check chains, guide blocks, or sway blocks to prevent the mower from swaying side to side and possible contact with tractor rear tires.
      • 5.2 3-Point Quick Hitch
      • 5.3 Connecting Mower - Lift Type (Quick Hitch)
        • 1. Make certain the implement’s upper and lower hitch pins are secured.
        • 2. Lower the tractor’s 3-point lift until the three Quick-Hitch hooks are lower than the implements hitch pins. Carefully back the tractor to align the Quick-Hitch hooks under the implement’s hitch pins.
        • 3. Slowly raise the tractor’s 3-point lift until the lower Quick-hitch hooks lock into place over the implement’s 3-point hitch pins.
          • 1. Driveline length
          • 2. Tractor stability
      • 5.4 Connecting the Mower-Pull Type
        • 1. Make sure the tractor is equipped with the correct PTO shaft and the drawbar is extended 14” from the PTO shaft end for a 540 RPM mower and 16” for a 1000 RPM unit.
        • 2. Block the mower wheels in place and use the attached parking jack to raise or lower the tongue clevis to the height of the tractor drawbar. The parking jack can be rotated 15 degrees in each direction to obtain a near vertical position. Note: Alwa...
        • 3. Board the tractor and start the engine. Back the tractor to the mower aligning the drawbar hitch hole with the mower hitch clevis. Turn off the tractor engine, set the parking brake, place the tractor in park, and dismount.
        • 4. To attach the mower, place two 1” flatwashers (1) positioned under top lip of tongue clevis and to the top of drawbar. Add additional 1” flatwashers (2) between the bottom of drawbar and bottom lip of clevis to fill open space. Insert a 3/4”...
        • 5. Securely attach mower safety chain to tractor drawbar or drawbar support frame.
        • 6. Lower the jack until the tongue is completely supported by the drawbar. Remove jack from the tongue and place on storage bracket of mower main frame.
        • 7. If using a hydraulic cylinder, connect hydraulic hose ends into tractor hydraulic ports.
        • 8. If the mower has been attached to a 3-point hitch drawbar, adjust any tractor equipped lower link check chains, guide blocks, or sway blocks to prevent the hitch and mower from swaying side to side. Note: Never raise the 3-point lift with the mowe...
      • 5.5 Safety Tow Chain
    • 6. SETTING THE MOWER
      • 6.1 Setting Mower Height- Lift Type
        • 1. Park the tractor and mower on level ground.
        • 2. Using the 3-point hitch control lever, position the front of the mower with its side skids 1” less off the ground than desired cut height. For example, for a 3” cut, position the skids 2” from the ground. Set the 3-point control lever stop a...
        • 3. Shut down the tractor and remove the key.
        • 4. Level the mower deck front to rear by extending or retracting the 3-point top link.
        • 5. Level the mower side to side by manipulating one lower lift arm length. On most tractors, at least one of the lift arms is designed to allow for manipulation of its length. Shortening or extending will allow for deck leveling from side to side.
        • 6. Securely block up the mower at this height.
        • 7. Remove the bolts securing the tailwheel beam support brackets and allow the tailwheels) to rest at ground level. Align beam and positioning bracket holes with closest set of holes in support brackets and reinstall securing the beam(s) in position....
        • 8. Extend the tractor’s top 3-point link so that when lifting the mower, the front of the deck will raise 2 to 2½" before the tail wheel(s) leaves the ground. This will allow the mower to follow the contour of uneven terrain.
      • 6.2 Setting Mowing Height - Pull Type and Semi-Mount Type Mowers
        • 1. Park the tractor and mower on level ground.
        • 2. Using the ratchet jack or hydraulic cylinder, position the mower so the skid shoes are 1” less off the ground than the desired final cut height. For example, if a 3” cut is desired, raise or lower the mower until the skid shoes are 2” off th...
        • 3. Adjust the mower leveling rod so that the front of the mower is approximately 3/4” lower than the rear. For semi mount units raise or lower 3- point lower links to set height of front of mower 3/4“lower than rear.
        • 4. If the mower is attached to a 3-point hitch drawbar, adjust any tractor equipped lower link check chains, guide blocks, or sway blocks to prevent the hitch and mower from swaying from side to side. Never raise the 3-point lift with the mower attac...
      • 6.3 Setting Deck Pitch
    • 7. DRIVELINE ATTACHMENT
      • 7.1 Driveline Length Check
      • 7.2 Constant Velocity (CV) Driveline
    • 8. PRE-OPERATION INSPECTION AND SERVICE
      • 8.1 Tractor Pre-Operation Inspection/Service
      • 8.2 Mower Pre-Operation Inspection/Service
      • 8.3 Cutting Component Inspection
      • 8.4 Blade Bolt Inspection
    • 9. DRIVING THE TRACTOR AND IMPLEMENT
      • 9.1 Starting the Tractor
      • 9.2 Brake and Differential Lock Setting
      • 9.3 Raising the Mower
      • 9.4 Driving the Tractor and Mower
      • 9.5 Crossing Ditches and Steep Inclines
    • 10. OPERATING THE TRACTOR AND IMPLEMENT
      • 10.1 Foreign Debris Hazards
      • 10.2 Bystanders/Passersby Precautions
      • 10.3 Engaging the Power Take Off (PTO)
      • 10.4 PTO RPM and Ground Speed
      • 10.5 Operating the Mower
    • 10.6 Right of Way (Highway) Mowing
      • 1. MAINTAIN MOWER SHIELDING in good operational condition,
      • 2. DAILY INSPECT the condition of the Thrown Object Guards, mower Side Skirts, and skid shoes: Replace or repair worn or damaged guards.
      • 3. DAILY INSPECT the condition of the Blades and Blade Bolts. Replace any cracked, worn, bent or damage blades. Always replace blade bolts and nuts when replacing blades. Make sure the blade bolts are properly tightened.
      • 4. RAISE CUTTING HEIGHT to 6 INCHES minimum.
      • 5. INSPECT AREA thoroughly before mowing to REMOVE potential THROWN OBJECT HAZARDS.
      • 6. NEVER ALLOW BLADES to CONTACT SOLID OBJECTS like wire, rocks, posts, curbs, guardrails, or ground while mowing.
        • 1. MARK objects that cannot be removed.
        • 2. AVOID these objects when mowing.
      • 10.7 Shutting Down the Implement
    • 11. DISCONNECTING THE MOWER FROM THE TRACTOR
    • 12. MOWER STORAGE
    • 13. TRANSPORTING THE TRACTOR AND IMPLEMENT
      • 13.1 Tire and Wheels
      • 13.2 Transporting on Public Roadways
    • 14. Hauling the Tractor and Implement
  • 15. TROUBLESHOOTING GUIDE
    • Problem Possible Cause Remedy
      • Blades worn, dull, or bent. Replace blades.
      • (Refer to “Maintenance” section).
      • Mower not level side to side. Adjust. (Refer to “Assembly” section)
      • Improper height adjustment. Adjust Mower height.
      • (Refer to “Assembly” section)
      • Low tractor tire pressure on Adjust tire pressure.
      • one side. (Refer to your tractor operator's
      • manual)
      • Turning too fast. Reduce ground speed when turning.
      • Tractor tires push grass down. Adjust your tractor wheel spacing.
      • (Refer to “Operation” section)
      • Damaged Mower pan. Repair or replace as necessary.
      • RPM too low Use full PTO speed.
      • (Refer to your tractor operator's manual)
      • Improper blade for direction of cut. Install blades so rotation is correct.
      • rear to hold and circulate material longer. (Refer to Operation Section- Setting the Mower-Setting Deck Height) Reduce ground speed.
      • Cutting too high. Lower cutting height. (Refer to Operation Section-Setting the Mower- Setting Deck Pitch)
      • Windrowing Material heavy and lush. Raise the front of Mower relative to the or Uneven rear. (Refer to Operation Section-
      • Distribution Setting the Mower-Setting Deck
      • Height)
      • Excessive ground speed Reduce ground speed.
      • Conditions too wet. Wait for conditions to dry. Reduce
      • ground speed.
      • Bolt hole elongated or oversized. Replace Blade Carrier.
      • Locknut worn out. Replace Locknut.
    • Gearbox Noisy Low Lubricant. Check lubricant level.
      • Rough gears. Run in or change Gears.
      • Worn Bearing. Replace Bearing.
      • Bent Shaft. Replace Oil Seal and Shaft.
      • Oil Seal Race rough. Replace Shaft or repair Race.
      • Oil Seal installed wrong. Replace Seal.
      • Oil Seal not sealing in the housing. Replace Seal or use a sealant on O.D.
      • of Seal.
      • Oil level too high. Drain oil to proper level.
      • Gasket damaged. Replace Gasket.
      • Bolts loose. Tighten Bolts.
      • Sand hole in casting. Replace castings or gearbox.
      • Blades unable to cut that part of ground speed of tractor but keep
      • grass pressed down by path of engine running at full PTO rpm.
      • tractor tires. Lowering the cutting height may help.
      • Dull blades. Sharpen or replace blades.
      • Height of cutter lower at rear or See Cutting Height Instructions.
      • front.
      • Improper type lubricant. Replace with proper lubricant.
      • Excessive trash build-up around Remove trash.
      • gearbox.
      • Bearing or gears set up improperly. Consult your Dealer.
      • Excessively 540 RPM.
      • Heavy Material. Reduce ground speed. Raise cutting
      • height.
      • Not using proper pin. Replace only with recommended shear pin.
      • PTO engaged at high engine RPM Idle engine to engage PTO
      • Cutting in rocky conditions Increase cutting height.
      • Blade carrier RPM too high. Check gearbox ratios.
      • Blades not properly heat treated. Consult your Dealer.
      • MAINTENANCE SECTION
    • HAZARDS WITH MAINTENANCE OF IMPLEMENT
    • PARTS INFORMATION
    • Lubrication
    • GEARBOX
    • TAIL WHEEL ASSEMBLY
• MAIN & JACKSHAFT DRIVELINE SHIELDS
  • DRIVELINE TAPER CONE YOKE REMOVAL INSTRUCTIONS
    • 1. Loosen 11/16” bolt end one revolution.
    • 2. Insert drift punch (max. diameter.375) into hole opposite the hex head and impact with hammer.
    • 3. Repeat operations 1 & 2.
    • 4. Remove clamping cone from yoke and yoke from shaft.
  • BLADE SERVICING
  • BLADE SHARPENING
  • BLADE CARRIER REMOVAL
  • BLADE CARRIER INSPECTION
  • BLADE CARRIER INSTALLATION
  • BLADE REMOVAL
  • BLADE TIMING PROCEDURE
    • 1. Raise the mower to minimum height to allow sufficient clearance between the mower deck and ground to visually inspect blade carriers.
    • 2. Completely shut down the tractor and secure the tractor in position by placing the tractor in park and setting the parking brake. Securely block the mower at this height.
    • 3. On a side gearbox, remove connecting coupler.
    • 4. Manually rotate carriers until blades are positioned at near 90 degree angle from one another. See Fig. Mnt-R-0102
    • 5. Replace connecting coupler.
    • 6. Manually spin carriers a complete rotation to ensure blades do not collide with one another.
• SLIP CLUTCH
• SEASONAL CLUTCH MAINTENANCE
  • 1. Loosen nuts (Figure Mnt-R-0251) on springs until the springs can freely rotate, yet remain secure on bolts.
  • 2. Attach mower to tractor and start the tractor. Set the engine speed at 1200 RPM.
  • 3. Engage the PTO (approximately one second) and then quickly disengage it. The friction lining plates shoulder break loose.
  • 4. Turn tractor off and tighten the nuts on the springs to their original position of 1-9/16” compressed spring length.
  • MOWER STORAGE
    • 1. Thoroughly clean the cutter.
    • 2. Lubricate the cutter as covered in Maintenance Section.
    • 3. Tighten all bolts and pins to the recommended torque.
    • 4. Check the cutter for worn or damaged parts. Make replacements immediately.
    • 5. Store the cutter in a clean, dry place with the cutter housing resting on blocks.
    • 6. Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the cutter.
  • PROPER TORQUE CHART FOR FASTENERS
• AEM-FEMA Ind-Agri Mower Manual 10-10.pdf
  • English Cover.pdf
    • Page 1
  • Complete Ind Ag Mower Spanish 10-10.pdf
    • Spanish Cover.pdf
      • Page 1
  • Complete Ind Ag Mower Spanish 10-10.pdf
    • Spanish Cover.pdf
      • Page 1
• Safety Section Page 7.pdf
  • GENERAL SAFETY INSTRUCTIONS AND PRACTICES
  • OPERATOR SAFETY
  • CONNECTION OR DISCONNECTING IMPLEMENT SAFETY
  • CRUSHING HAZARDS
  • THROWN OBJECT HAZARDS
    • 1. MARK objects that cannot removed.
    • 2. AVOID these objects when mowing.
      • 1. MAINTAIN MOWER SHIELDING, side skirts, skid shoes, and blades in good operational condition,
      • 2. RAISE CUTTING HEIGHT to 6 INCHES minimum,
      • 3. INSPECT AREA thoroughly before mowing to REMOVE potential THROWN OBJECT HAZARDS,
      • 4. NEVER ALLOW BLADES to CONTACT SOLID OBJECTS like wire, rocks, post, curbs, guardrails, or ground while mowing. PN TO02
    • 1. BLADES CAN FAIL from impact and objects can be thrown with great velocity.
    • 2. INSPECT and REPLACE any damaged blades.
    • 3. CHECK blade carrier balance and REPLACE if damaged.
      • 1. STOP PTO and back up mower.
      • 2. LOWER mower, engage PTO and mow forward.
  • RUN OVER HAZARDS
  • PTO ENTANGLEMENT HAZARDS
  • MOWER BLADE CONTACT HAZARDS
  • HIGH PRESSURE OILLEAK HAZARDS
  • ELECTRICAL & FIRE HAZARDS
  • TRANSPORTING HAZARDS
  • HAZARDS WITH MAINTENANCE OF IMPLEMENT
  • PARTS INFORMATION
  • Decal Location - Lift Type
    • 4. D389 1 DECAL Multi Hazard
    • 5. D388 1 DECAL Driveline Hazards
    • 6. 00756004 3 DANGER Shield Missing. Do Not Operate
    • 7. 00756005 2** DANGER Rotating D/L Entanglement
    • 8. D137 1 INSTRUCT CCW Blade Rotation, Blade Bolt Torque
    • 9. D138 1 INSTRUCT CW Blade Rotation, Blade Bolt Torque
    • 10. D454 1 WARNING Crushing Hazard (Decal under Deck)
    • 11. 00771283 3 INFORMATION 5 Year Gearbox Warranty
    • 12. D608 2 WARNING Blade Timing
    • 13. 99102 1 LOGO Rhino Logo
    • 14. 00787406 2 NAME Rhino
    • 15. 00785579 2 NAME Turbo 96
    • 16. 00785578 1 NAME Turbo 96
    • 17. D302 2 LOGO Rhino Logo (4-7/8 x 6-1/2)
    • 18. 03200347 * REFLECTOR SMV Sign
    • 19. 00760657 1 IMPORTANT Rhino Genuine Parts, Rotary Mower
    • 20. nfs 1 SER PLT Serial Number Plate
    • 21. D401 1 INSTRUCT 1000 RPM
    • 22. 1458392 2 REFLECTOR Red Reflectors
    • 23. 1458393 2 REFLECTOR Amber Reflectors
    • 24. 00776031 1 ___________ Canister, Operator’s Manual
    • 25. 00778586C 1 ___________ Operator’s Manual
    • 26. 10058000 3 ___________ Bolt
    • 27. 00024100 6 ___________ Flatwasher
    • 28. 02959924 3 ___________ Locknut
    • 29. 00785538 1 LOGO Turbo Dome Deck
    • 30. D614 2 DANGER Thrown Object Shield Missing
    • 31. D534 2 WARNING Blade Bolt Torque
    • 32. D629 1 INSTRUCT Lubrication Chart
  • Decal Location - Pull Type
    • 1. D389 1 DECAL Multi Hazard
    • 2. D388 1 DECAL Driveline Hazards
    • 3. 00756004 3 DANGER D/L Shield Missing. Do Not Operate
    • 4. 00756005 2** DANGER Rotating D/L Entanglement
    • 5. D137 1 INSTRUCT CCW Blade Rotation
    • 6. D138 1 INSTRUCT CW Blade Rotation
    • 7. D454 1 WARNING Crushing Hazard (Decal under Deck)
    • 8. 00771283 3 INFORMATION 5 Year Gearbox Warranty
    • 9. D608 2 WARNING Blade Timing
    • 10. 99102 1 LOGO Rhino Logo
    • 11. 00787406 2 NAME Rhino
    • 12. 00785579 2 NAME Turbo 96 (Large)
    • 13. 00785578 1 NAME Turbo 96 (Small)
    • 14. D302 2 LOGO Rhino Logo (4-7/8 x 6-1/2)
    • 15. 03200347 * REFLECTOR SMV Sign
    • 16. 00760657 1 IMPORTANT Rhino Genuine Parts
    • 17. nfs 1 SER PLT Serial Number Plate
    • 18. D401 1 INSTRUCT 1000 RPM
    • 19. 1458392 2 REFLECTOR Red Reflectors
    • 20. 1458393 2 REFLECTOR Amber Reflectors
    • 21. 00776031 1 ___________ Canister, Operator’s Manual
    • 22. 00778586C 1 ___________ Operator’s Manual
    • 23. 10058000 3 ___________ Bolt
    • 24. 00024100 6 ___________ Flatwasher
    • 25. 02959924 3 ___________ Locknut
    • 26. 00785538 1 INFORMATION Turbo Dome Deck
    • 27. D614 2 DANGER Thrown Object Shield Missing
    • 28. D534 2 WARNING Blade Bolt Torque
    • 29. D629 1 INSTRUCT Lubrication
    • 30. D390 1 DECAL Pull Type Unit Hazards
    • 31. D518 1 WARNING Jack Positioning
  • Decal Description
    • Federal Laws and Regulations
      • SAFETY SECTION