Document Outline

• INSTALLATION AND OPERATING MANUAL
  • List of Contents
  • Relevant documents
  • 1 Technical data
    • 1.1 Tightening torques
    • 1.2 Type plate, dry-running, ATEX and housing markings
    • 1.3 Spare parts
  • 2 Safety
    • 2.1 Intended use
    • 2.2 Notes on safety for the customer / operator
    • 2.3 Notes on safety for maintenance
    • 2.4 Conversion work and production of spare parts by the customer
    • 2.5 Improper operation
    • 2.6 Special requirements for explosion protection
      • 2.6.1 Filling the unit
      • 2.6.2 Special operating conditions
      • 2.6.3 Chargeable liquids
      • 2.6.4 Identification
      • 2.6.5 Check of the direction of rotation
      • 2.6.6 Mode of operation of the pump
      • 2.6.7 Temperature limits
      • 2.6.8 Maintenance
      • 2.6.9 Electric peripheral equipment
  • 3 Transport, storage and disposal
    • 3.1 Return consignments
    • 3.2 Disposal
  • 4 Product description
  • 5 Installation
    • 5.1 Safety regulations
    • 5.2 Installation of pump/unit
    • 5.3 Alignment of pump-coupling-motor
    • 5.4 Piping
      • 5.4.1 Nominal size
      • 5.4.2 Nozzle loads
      • 5.4.3 Suction line
      • 5.4.4 Supply lines
      • 5.4.5 Discharge line
      • 5.4.6 Venting and evacuating
    • 5.5 Pipe fittings
    • 5.6 Monitoring facilities
    • 5.7 Drive
    • 5.8 Coupling
    • 5.9 Final check
    • 5.10 Coupling guard
    • 5.11 Electric connection
  • 6 Commissioning/Shutdown
    • 6.1 Initial commissioning
      • 6.1.1 Filling the pump housing
      • 6.1.2 Start-up
    • 6.2 Operating limits
      • 6.2.1 Abrasive media
      • 6.2.2 Min./max. flow rate
    • 6.3 Shutdown
    • 6.4 Restarting
    • 6.5 Improper operations and their consequences (examples)
  • 7 Maintenance
    • 7.1 Safety-relevant screw fittings
    • 7.2 Bearing pedestal
      • 7.2.1 Long life grease lubrication
      • 7.2.2 Oil bath lubrication
    • 7.3 Cleaning
    • 7.4 Stand-by pumps
    • 7.5 Notes on dismantling
      • 7.5.1 Protective clothing
      • 7.5.2 Magnetic fields
    • 7.6 Dismantling
      • 7.6.1 Removing bearing pedestal
      • 7.6.2 Dismantling of drive unit long life grease lubrication
      • 7.6.3 Dismantling of drive unit oil bath lubrication
      • 7.6.4 Dismantling of slide-in unit
      • 7.6.5 Dismantling housing/shaft spider
      • 7.6.6 Changing the radial ball bearings
    • 7.7 Notes on assembly
      • 7.7.1 Table for target dimension Z
    • 7.8 Assembly
      • 7.8.1 Assembly of housing / shaft spider
      • 7.8.2 Assembly of slide-in unit
      • 7.8.3 Assembly of drive unit long life grease lubrication
      • 7.8.4 Assembly of drive unit oil bath lubrication
      • 7.8.5 Final assembly
      • 7.8.6 Fill bearing pedestal with oil
    • 7.9 Tests
  • 8 Malfunctions
  • 9 Sectional drawings
    • 9.1 Legend
    • 9.2 Long life grease lubrication
    • 9.3 Oil bath lubrication
  • 10 Assembly aids
    • 10.1 Boring template for housing drain
    • 10.2 Pull-off device for plain bearing bushes
    • 10.3 Dismantling device impeller-inner magnet assembly
• Operating limits
• Declaration of Conformity with ATEX
• Declaration of Conformity without ATEX
• Safety Information / Declaration of No Objection