Document Outline

• Product Overview
  • 1.1 Description
  • 1.2 Operation
    • 1.2.1 Supervised System
    • 1.2.2 Distance-Read Leak Detection
    • 1.2.3 User Configuration and Communication
• Installation
  • 2.1 Prepare for Installation
  • 2.2 Mount the LD5200
  • 2.3 Establish Physical Connections
    • 2.3.1 TB1: 4-20mA Output
    • 2.3.2 TB2: Sensing Cable Interface
    • 2.3.3 TB3: Maintenance Relay
    • 2.3.4 TB4: Two Fault/Leak Relay Outputs
    • 2.3.5 P1: EIA-232 Connector
    • 2.3.6 SW1: TB5 Port 3 Termination Switch
    • 2.3.7 TB5 and TB6: EIA-485 Modbus Ports
    • 2.3.8 SW2: TB6 Port 2 (Bottom Row) Termination Switch
    • 2.3.9 SW3: TB6 Port 1 (Top Row) Termination Switch
    • 2.3.10 P2: RJ45 Network
    • 2.3.11 P3: Optional Power Connection
    • 2.3.12 TB7: Input Power (from Input AC Power Supply)
    • 2.3.13 DS1: Status LED
  • 2.4 Connect the SeaHawk Sensing Cable
    • 2.4.1 Connect Lengths of Sensing Cable
    • 2.4.2 Secure Sensing Cable to the Floor
  • 2.5 Apply Power to the LD5200
  • 2.6 Configure Communications
    • 2.6.1 Access the Configuration Menu
  • 2.7 Test the System
  • 2.8 Calibrate Cable Resistance
  • 2.9 Configure Security Settings
  • 2.10 General Operation
• LCD Touch Screen Interface
  • 3.1 Main Menu
  • 3.2 Silence Button
  • 3.3 Alarms Button
    • 3.3.1 History
  • 3.4 Status Button
    • 3.4.1 System Button
  • 3.5 Setup Button
    • 3.5.1 Leak Settings
    • 3.5.2 Virtual Zone
    • 3.5.3 Slave Zone
    • 3.5.4 4-20mA Output
    • 3.5.5 Preventative Maintenance
    • 3.5.6 System Settings
    • 3.5.7 EIA-485 / Modbus / N2
    • 3.5.8 Bacnet
    • 3.5.9 Clear History
• Web Interface
  • 4.1 Home Page
  • 4.2 Identity
  • 4.3 Configuration
    • 4.3.1 Leak
    • 4.3.2 Virtual Zone
    • 4.3.3 Slave Controller
    • 4.3.4 Slave Zones
    • 4.3.5 Network/IP
    • 4.3.6 Network Statistics
    • 4.3.7 Web
    • 4.3.8 Map
    • 4.3.8.1 Upload the Map Image
    • 4.3.8.2 Map Reference Points
    • 4.3.8.3 Test the Mapped Coordinates
    • 4.3.8.4 Viewing the Map
      • 4.3.9 Clock
      • 4.3.10 NTP
      • 4.3.11 Email-SMTP/DNS
      • 4.3.12 SNMP/Syslog
      • 4.3.13 EIA-485 Port/Modbus/N2
      • 4.3.14 Bacnet
      • 4.3.15 Alarm Management
      • 4.3.16 System/Flash Management
      • 4.3.17 Product Registration
  • 4.4 Historical Data
  • 4.5 Refresh
• Modbus Communication
  • 5.1 Comm Port Settings
  • 5.2 Leak Detection Modbus Master
    • 5.2.1 Connect Distance Read Panels to the LD5200
  • 5.3 Implementation Basics
    • 5.3.1 Modes of Transmission
    • 5.3.1.1 Slave Address Field
    • 5.3.1.2 Function Field
    • 5.3.1.3 Data Field
    • 5.3.1.4 Error Check (Checksum) Field
  • 5.4 Packet Communications For The LD5200
    • 5.4.1 Function 03: Read Output Registers
    • 5.4.2 Function 04: Read Input Registers
    • 5.4.3 Function 06: Preset Single Register
    • 5.4.4 Function 16: Preset Multiple Registers
  • 5.5 RTU Framing
• Update Firmware
  • A.1 Update the LD5200 Firmware
• EIA-232 Interface
  • B.1 Set the IP Address through the EIA-232 Port
  • B.2 Boot Up
  • B.3 Main Menu
  • B.4 Other Main Menu Functions
• Preventive Maintenance
• Troubleshooting
  • D.1. Troubleshooting Problems with the LD5200
  • D.2. Troubleshooting Sensing Cable
• 4-20mA Output Testing
• Technical Specifications