Document Outline

• 1732E-UM003B-EN-P 1732E ArmorBlock EtherNet/IP Dual Port 8-Point Sequence of Events Input and Scheduled Output Modules User Manual
  • Preface
  • Summary of Changes
  • Table of Contents
  • 1 - About ArmorBlock Modules
    • About ArmorBlock Modules
      • Overview
      • Module Features
      • Hardware/Software Compatibility
      • Use of the Common Industrial Protocol (CIP)
      • Understand the Producer/ Consumer Model
      • Specify the Requested Packet Interval (RPI)
      • Chapter Summary and What’s Next
  • 2 - Module Overview and Features
    • Module Overview and Features
      • Overview
      • EtherNet/IP Network Overview
      • Introduction to CIP Sync
        • What is IEEE 1588 PTP (Precision Time Protocol)?
        • CIP Sync Support
        • What is CIP Sync?
        • What is Time Stamping?
      • Introduction to the Sequence of Events Input Module
        • High Performance Sequence of Events Applications in the Logix Architecture
        • First Fault Detection
        • Time Stamped I/O
        • High Speed Applications
        • Motion Control
        • Global Position Registration
      • Introduction to Scheduled Output Module
        • Operation
        • High Speed Product Reject
      • Chapter Summary and What’s Next
  • 3 - Use the Modules in an ArmorBlock System
    • Use the Modules in an ArmorBlock System
      • Introduction
      • Differences Between Module and Standard I/O
      • Similar Functionality to Standard ArmorBlock
      • Chapter Summary and What’s Next
  • 4 - Install Your Module
    • Install Your Module
      • Overview
      • Install the Module
        • Set the Network Address
      • Mount the Module
      • Wire the Module
        • Power Connectors
      • Chapter Summary and What’s Next
  • 5 - Configure the Module for Your EtherNet/IP Network
    • Configure the Module for Your EtherNet/IP Network
      • Introduction
      • Configuration Requirements
        • IP Address
        • Gateway Address
        • Subnet Mask
      • Set the Network Address
      • Use the Rockwell Automation BootP/DHCP Utility
        • Save the Relation List
      • Use DHCP Software to Configure Your Module
      • Chapter Summary and What’s Next
  • 6 - Configure the Module Using RSLogix 5000 Software
    • Configure the Module Using RSLogix 5000 Software
      • Introduction
      • Set Up the Hardware
      • Create the Example Application
      • Configure Your I/O Module
        • RSLogix 5000 Configuration Software
      • Overview of the Configuration Process through RSLogix 5000
      • Add a New Bridge and Module to Your RSLogix 5000 Project
        • Add the Local EtherNet/IP Bridge to the I/O Configuration
        • Add the I/O module as a child of the 1756-EN2T module
      • Use the Default Configuration
      • Change the Default Configuration
      • Download Your Configuration
      • Edit Your Configuration
      • Access Module Data in RSLogix 5000 Software
      • Configure RSLogix 5000 and the 1756-EN2T Communication Module for CIP Sync
      • Chapter Summary and What’s Next
  • 7 - Common Features of the 1732E-IB8M8SOER and 1732E-OB8M8SR Modules
    • Common Features of the 1732E-IB8M8SOER and 1732E-OB8M8SR Modules
      • Introduction
      • Communications Format
      • Electronic Keying
      • Module Inhibiting
      • Module Fault Reporting
      • Fully Configurable via Software
      • Producer/Consumer Model
      • Status Indicator Information
      • Agency Certifications
      • Chapter Summary and What’s Next
  • 8 - Specific Features of the 1732E-IB8M8SOER Sequence of Events Input Module
    • Specific Features of the 1732E-IB8M8SOER Sequence of Events Input Module
      • Introduction
      • Determine Module Compatibility
      • Operational Modes
      • Timestamp Latching
      • Software Configurable Input Filters
      • Sync to Master
      • Chapter Summary and What’s Next
  • 9 - Specific Features of the 1732E-OB8M8SR Scheduled Output Module
    • Specific Features of the 1732E-OB8M8SR Scheduled Output Module
      • Introduction
      • Operational Modes
        • Time-Scheduled Output Control
      • Configurable Point-Level Output Fault States
        • Output State
      • Chapter Summary and What’s Next
  • 10 - Use the Sequence of Events Input and Scheduled Output Modules
    • Use the Sequence of Events Input and Scheduled Output Modules
      • Introduction
      • Overview
      • Use the Sequence of Events Input Module
        • How Does 1732E-IB8M8SOER Store Timestamp Data?
        • Use Timestamp Latching
        • Use Timestamp Capture
        • Operational Modes
        • Manage the Data
        • Module Sends Data to the Controller
        • Copy Relevant Input Data to a Separate Data Structure
        • Acknowledge Timestamp Latching Timestamp Data
        • Sort the Data
        • Clear All Data From the Module Buffer At Once
        • Propagate a Signal From Input Pin to EtherNet
        • Per Point Mode of Operation
      • Use the Scheduled Output Module
        • Usage with MAOC Instruction
        • I/O Subsystem
        • Schedule Processing
      • Chapter Summary and What’s Next
  • 11 - Troubleshoot the Module
    • Troubleshoot the Module
      • Troubleshoot the Module
        • Determine Fault Type
      • Chapter Summary
  • 12 - Interpret Status Indicators
    • Interpret Status Indicators
      • Introduction
      • Chapter Summary and What’s Next
  • A - Specifications
    • Specifications
      • Specifications
  • B - Module Tags
    • Module Tags
      • Fault and Status Reporting Between the Module and Controllers
      • Module Tag Names and Definitions
        • Tags Used
  • C - Data Tables
    • Data Tables
      • Communicate with Your Module
        • Connection Points
  • D - Connect to Networks via Ethernet Interface
    • Connect to Networks via Ethernet Interface
      • ArmorBlock Module and Ethernet Communication
      • ArmorBlock module and PC Connections to the Ethernet Network
        • Ethernet Network Topology
        • Connecting to an Ethernet Network
        • Cables
      • EtherNet/IP Connections
      • Duplicate IP Address Detection
      • Configure Ethernet Communications on the ArmorBlock module
      • Configure Using RSLogix 5000 Software
      • Configure Using Web Server
  • E - 1732E ArmorBlock Embedded Web Server
    • 1732E ArmorBlock Embedded Web Server
      • Introduction
      • Typical Applications
      • Browser Requirements
      • Access the Home Page of the Web Server
      • Log On to the Web Server
      • Navigate the 1732E ArmorBlock I/O
      • Access Diagnostic Information
• Index
• Back Cover