Document Outline

• POINT Guard I/O Safety Modules, 1734-UM013J-EN-P
• Important User Information
• Summary of Changes
  • New and Updated Information
• Table of Contents
• Preface
  • Studio 5000 Environment
  • Terminology
  • Access Product Release Notes
  • Additional Resources
• 1 - POINT Guard I/O Overview
  • Understand Suitability for Use
  • Safety Precautions
    • Installing and Replacing Modules
  • POINT Guard I/O Modules in CIP Safety Systems
    • 1734-IB8S Digital Input Module Features
    • 1734-OB8S Safety Digital Output Module Features
    • 1734-IE4S Safety Analog Input Module Features
    • Programming Requirements
    • CIP Safety Architectures
  • Safety Application Requirements
• 2 - Safety Inputs, Safety Outputs, and Safety Data
  • Safe States
    • POINT Guard Digital I/O Modules
    • POINT Guard I/O Analog Input Module
  • Safety Inputs (1734-IB8S)
    • Using a Test Output with a Safety Input
    • Single-channel Mode
    • Dual-channel Mode and Discrepancy Time
    • Dual-channel, Equivalent
    • Dual-channels, Complementary
    • Safety Input Fault Recovery
    • Input Delays
  • Safety Analog Inputs (1734-IE4S)
    • Input Range
    • Scaling
    • Digital Input Filter
    • Sensor Power Supply
    • Channel Offset
    • Process Alarms
    • Using a Single-channel Sensor
    • Dual-channel Equivalent Mode
    • Tachometer Mode
  • Safety Outputs (1734-OB8S)
    • Safety Output with Test Pulse
    • Dual-channel Mode
    • Safety Output Fault Recovery
  • Muting Lamp Operation (1734-IB8S)
  • I/O Status Data
    • Digital I/O Status Data
    • Analog I/O Status Data
• 3 - Guidelines for Placing Power Supplies and Modules in a System
  • Choosing a Power Supply
  • Power Supply Examples
    • Example 1: Isolating Field Power Segments
    • Example 2: POINT Guard I/O Used with AC I/O Modules
  • Placing Series A Digital and Analog Modules
  • Placing Series B Digital Modules
• 4 - Install the Module
  • Precautions
    • European Hazardous Location Approval
    • North American Hazardous Location Approval
    • Environment and Enclosure
    • Preventing Electrostatic Discharge
  • Mount the Module
    • Install the Mounting Base
    • Connect the Module to the Mounting Base
    • Connect the Removable Terminal Block
    • Remove a Mounting Base
  • Wire Modules
    • Terminal Layout
  • Connection Details
  • Wiring Examples
    • Emergency Stop Dual-channel Devices
    • Single-channel Safety Contactor
    • Dual-channel Safety Contactors
    • Safety Analog Input Wiring
• 5 - Configure the Module in a GuardLogix Controller System
  • Setting Up the Module
  • Add and Configure the Ethernet Bridge Module
  • Add and Configure the 1734 Ethernet Adapter
  • Add and Configure Safety Digital Input Modules
    • Add the Safety Digital Input Module
    • Configure the Safety Digital Inputs
    • Configure the Test Outputs
  • Add and Configure Safety Digital Output Modules
    • Add the Safety Digital Output Module
    • Configure the Safety Digital Outputs
  • Add and Configure Safety Analog Input Modules
    • Add the Safety Analog Input Module
    • Configure the Safety Analog Input Channel Operation
    • Configure the Safety Analog Inputs
    • Configure Safety Analog Input Alarms (optional)
    • Configure Tachometer Operation
  • Values and States of Tags
  • Configure Safety Connections
  • Configuration Ownership
  • Saving and Downloading the Module Configuration
  • Using ControlFLASH Software to Update POINT Guard I/O Modules
• 6 - Configure the Module for a SmartGuard Controller
  • Before You Begin
  • Set the Node Address
  • Auto-addressing with a 1734-PDN Adapter
  • Set Up Your DeviceNet Network
  • Configure the POINT Guard I/O Modules
    • Configure Digital Safety Inputs and Test Outputs
    • Configure Digital Safety Outputs
    • Configure Safety Analog Inputs
  • Configure the SmartGuard Controller
    • Set Up the Input and Output Connections
    • Complete the Set Up of the SmartGuard Controller
  • Save and Download Module Configuration
• 7 - Configuring Safety Connections between a GuardLogix Controller and POINT Guard I/O Modules on a DeviceNet Network
  • Configure the Module in RSNetWorx for DeviceNet Software
  • Add the POINT Guard I/O Module to the Controller Project
  • Complete the Safety Configuration
  • Download the DeviceNet Network Configuration
  • Verify Your DeviceNet Safety Configuration
    • Determine If Devices Can Be Verified
    • Select Devices to Verify
    • Review the Safety Device Verification Reports
    • Lock Safety Devices
• 8 - Replacing POINT Guard I/O Modules
  • The Safety Network Number
  • Manually Setting the Safety Network Number
  • Resetting a Module to Out-of-box Condition
    • By Using the Logix Designer Application
    • By Using RSNetWorx for DeviceNet Software
  • Replacing a Module in a GuardLogix System on an EtherNet/IP Network
    • Replacement with ‘Configure Only When No Safety Signature Exists’ Enabled
    • Replacement with ‘Configure Always’ Enabled
  • Replacing a Module When Using a SmartGuard or GuardLogix Controller on a DeviceNet Network
• A - Indicators
  • Module
  • Network Status
  • Configuration Lock
  • Power
  • 1734-IE4S Sensor Power
  • 1734-IE4S Safety Analog Input Status
  • 1734-IB8S Safety Input Status
  • 1734-OB8S Safety Output Status
• B - Get I/O Diagnostic Status from Modules in Logix Systems
  • Message Instructions
  • Configure the Message Instruction
  • Class, Instance, and Attribute Data for I/O Modules
• C - Specifications
  • Technical Specifications for Series A Modules
    • Safety Digital Input Module Specifications
    • Safety Digital Output Module Specifications
    • Safety Analog Input Module Specifications
  • Technical Specifications for Series B Modules
    • Safety Digital Input Module Specifications
    • Safety Digital Output Module Specifications
  • Environmental Specifications
  • Certifications
  • Legislations and Standards
• D - Safety Data
  • Series A Safety Data
  • Series B Safety Data
• E - Configuration Parameters
• F - I/O Assemblies
  • Input Assemblies
  • Output Assemblies
  • Analog Input Assemblies
  • Configuration Assemblies
  • Using Data from Modules Configured via the Generic Profile
• G - History of Changes
  • 1734-UM013I-EN-P, May 2013
  • 1734-UM013H-EN-P, August 2012
  • 1734-UM013G-EN-P, August 2012
  • 1734-UM013F-EN-P, June 2012
  • 1734-UM013E-EN-P, March 2012
  • 1734-UM013D-EN-P, September 2011
  • 1734-UM013C-EN-P, August 2010
  • 1734-UM013B-EN-P, June 2009
  • 1734-UM013A-EN-P, February 2009
• Index