Document Outline

• POINT I/O and ArmorPOINT I/O DeviceLogix Modules User Manual
  • Important User Information
  • Table of Contents
  • Preface
    • Purpose of This Manual
    • Who Should Use This Manual
    • Related Publications
  • Chapter 1
    • Introduction
      • About This Chapter
      • About the Modules
        • 1734-8CFGDLX
        • 1738-8CFGDLXM8, 1738-8CFGDLXM12, and 1738-8CFGDLXM23
      • Modes of Usage
        • Standard POINT I/O Module
        • Stand Alone DeviceLogix
        • Peer Enabled POINT I/O
      • Quick Start - Prepare the Modules to work on DeviceNet
      • Quick Start - Prepare the Modules to work on EtherNet/IP and ControlNet
  • Chapter 2
    • Install POINT I/O DeviceLogix Modules
      • About This Chapter
      • Install the Mounting Base Assembly
      • Install an I/O Module
      • Install the Removable Terminal Block
      • Remove a 1734-TB or 1734-TBS Base
      • Remove a 1734-TOP or 1734-TOPS Base
      • Wire the Modules
        • 1734-8CFGDLX I/O Module
        • 1734-8CFGDLX Wiring Diagram
        • System and Power Considerations
  • Chapter 3
    • Install ArmorPOINT I/O DeviceLogix Modules
      • About This Chapter
      • Install the Mounting Base
      • Install the Module
        • Remove the Module from the Mounting Base
      • Wire the Modules
        • 1738-8CFGDLXM8 I/O Module
        • 1738-8CFGDLXM12 I/O Module
        • 1738-8CFGDLXM23 I/O Module
  • Chapter 4
    • DeviceLogix for POINT I/O and ArmorPOINT I/O on DeviceNet
      • About This Chapter
      • Offline Configuration using RSNetworx for DeviceNet
        • Example: Build the Backplane
      • Online Configuration using RSNetWorx for DeviceNet
      • I/O Data Assembly Maps
  • Chapter 5
    • DeviceLogix for POINT I/O and ArmorPOINT I/O on Ethernet/ControlNet
      • About This Chapter
      • Add a POINT I/O DeviceLogix Module to RSLogix 5000
        • I/O Tags
      • Launch RSNetworx for DeviceNet to Configure the Module
  • Chapter 6
    • Configuring POINT I/O and ArmorPOINT I/O DeviceLogix modules using RSNetworx for DeviceNet
      • About This Chapter
      • Configure the Module using the Configuration tab
        • Parameters on the Parameters tab
      • Configure Peer Communication
        • Set Up Peer Communication Parameters
      • Produce Data Without Using a Master
      • Start the Function Block Editor
  • Chapter 7
    • DeviceLogix Capabilities
      • About This Chapter
      • Function Block Instructions
        • Process Category
        • Filter Category
        • Select Limit Category
        • Statistical Category
        • Timer/Counter Category
        • Comparison Category
        • Compute Category
        • Move/Logical Category
        • Logic Execution Time
        • Digital Inputs to Function Blocks
        • Analog Inputs to Function Blocks
        • Digital Outputs from Function Blocks
        • Analog Outputs from Function Blocks
      • Enable Line feature
      • Offline and Online Editing
      • Enable/Disable Logic
        • Logic Enable On
        • Logic Enable Off
        • Dependent Mode
      • Messaging
  • Chapter 8
    • Troubleshooting
      • About This Chapter
      • About Module Diagnostics
      • Status Indicators of POINT I/O Module
        • 1734-8CFGDLX Module
      • Status Indicators of ArmorPOINT I/O Modules
        • 1738-8CFGDLXM8, 1738-8CFGDLXM12, and 1738-8CFGDLXM23
      • Troubleshooting Scenarios
        • Peer connection is not working
        • Configuration or DeviceLogix program cannot be downloaded to the module
        • Module’s DeviceLogix program exits the Run mode unexpectedly
  • Appendix A
    • Peer Data Maps
      • About This Appendix
      • Peer I/O Sizes
        • Digital Input Modules
        • Analog and Specialty Input Modules
      • Peer Data Maps
        • 2-Point Digital Input Modules
        • 4-Point Digital Input Modules
        • 4-Point Digital Input with Diagnostics Modules
        • 8-Point Digital Input Modules
        • 8-Point Configurable Modules
        • 16-Point Digital Input Module
        • 8-Point Digital Input Modules with DeviceLogix
        • 2-Point Analog Input Modules and RTD (Resistant Temperature Device)
        • 4-Point Analog Input Modules
        • 8-Point Analog Input Modules
        • 2-Point Thermocouple Input Modules
        • Very High Speed Counter Input Modules
        • Encoder/Counter Input Modules
        • Synchronous Serial Interface Modules
        • RS232 and RS485 Interface Module
        • Installation Assistance
        • New Product Satisfaction Return
• Back Cover