Document Outline

• Stratix 8000 and 8300 Ethernet Managed Switches User Manual
  • Important User Information
  • Summary of Changes
    • New and Updated Information
  • Table of Contents
  • Preface
    • Studio 5000 Environment
    • Access Product Release Notes
    • Additional Resources
  • 1 - Install the Switch
    • Before You Begin
      • Parts List
      • Required Tools and Equipment
      • Product Dimensions
    • Install the Switch
    • Attach Expansion Modules (optional)
    • Mount the Switch on a DIN Rail
    • Mount the Switch on a Wall or Panel
    • Install an SFP Module (optional)
    • Ground the Switch
    • Wire the DC Power Source for the Switch
    • Wire the DC Power Source for the PoE Expansion Module (optional)
    • Attach the Power and Relay Connector to the Switch
    • Attach the Power Connector to the PoE Expansion Module (optional)
    • Wire External Alarms (optional)
    • Connect to 10/100 Copper Ports
    • Connect to a PoE Expansion Module Port
    • Connect to Dual-purpose Uplink Ports
      • Connect to 10/100/1000 Uplink Ports
      • Connect to SFP Fiber Ports
    • Connect to 100BaseFX Ports
    • Install or Remove the CompactFlash Card
    • Reset the Switch to Factory Defaults
    • Troubleshoot the Installation
      • Switch POST Results
      • POST Results with a Terminal
      • Bad or Damaged Cable
      • Ethernet and Fiber Cables
      • Link Status
      • Transceiver Issues
      • Port and Interface Settings
  • 2 - Getting Started
    • Switch Front Panel Description
    • Expansion Module Front Panel Descriptions
    • Hardware Features
    • CompactFlash Memory Card
    • Set Up the Switch Initially with Express Setup
    • Switch Memory Allocation
    • Device Manager Web Interface
      • Hardware Requirements
      • Software Requirements
    • Studio 5000 Environment
      • Hardware Requirements
    • Cisco Network Assistant
    • Command Line Interface
  • 3 - Switch Software Features
    • Port Numbering
    • Global Macro
    • Smartports
      • Optimize Ports through Port Roles
      • Avoid Smartports Mismatches
    • Power over Ethernet (PoE) Ports
      • Powered Device Detection and Initial Power Allocation
      • Power Management Modes
    • VLANs
      • Isolate Traffic and Users
      • Isolate Different Traffic Types
      • Group Users
    • IGMP Snooping with Querier
    • Spanning Tree Protocol
      • Rapid Spanning Tree Protocol
    • Storm Control
      • Default Storm Control Configuration
    • Port Security
      • Dynamic Secure MAC Address (MAC ID)
      • Static Secure MAC Address (MAC ID)
      • Security Violations
    • EtherChannels
    • DHCP Persistence
    • CIP Sync Time Synchronization (Precision Time Protocol)
    • Resilient Ethernet Protocol
      • REP Open Segment
      • REP Ring Segment
      • Access Ring Topologies
      • Link Integrity
    • SNMP
      • Supported MIBs
    • Port Mirroring
    • Layer 3 Routing (Stratix 8300 switch only)
      • Types of Routing
    • Static and Connected Routing
    • Alarms
    • Cryptographic IOS Software (optional)
    • Cable Diagnostics
    • Advanced Software Features
  • 4 - Manage the Switch via the Device Manager Web Interface
    • Access the Device Manager Web Interface
    • Dashboard Overview
      • Front Panel View and Status Indicators
      • Switch Information
      • Switch Health
      • Port Utilization
    • Configure Smartports
      • Customize Smartport Role Attributes
    • Configure Port Settings
      • Configure Ports to Use QuickConnect Technology
    • Configure Port Thresholds
    • Configure EtherChannels
    • Configure DHCP
      • Set up the DHCP Server
      • Configure a DHCP IP Address Pool
      • Reserve IP Addresses through DHCP Persistence
    • Configure VLANs
      • Assign Ports to VLANs
    • Configure Power over Ethernet (PoE) Ports
    • Configure PTP Time Synchronization
    • Enable Static and Connected Routing
      • Enable Connected Routing Only
      • Enable Both Static and Connected Routing
    • Configure STP
      • Global Settings
      • PortFast Settings
    • Configure REP
    • Configure Port Security
    • Configure IGMP Snooping
    • Configure SNMP
      • Use SNMP Management Applications
    • Configure Alarm Settings
      • Alarm Relay Settings
      • Global Alarms
      • Port Alarms
    • Configure Alarm Profiles
    • Monitor Trends
    • Monitor Port Statistics
    • Monitor REP Topology
    • Monitor CIP Status
    • Diagnose Cabling Problems
    • View System Log Messages
    • Use Express Setup to Change Switch Settings
    • Manage Users
    • Reallocate Switch Memory for Routing
    • Restart the Switch
    • Upgrade the Switch Firmware
    • Upload and Download Configuration Files
  • 5 - Manage the Switch via the Studio 5000 Environment
    • EtherNet/IP CIP Interface
      • CIP Network Connections
      • RSLinx Software and Network Who Support
      • Electronic Data Sheet (EDS) Files
      • Data Accessible with CIP
    • Add a Switch to the I/O Configuration Tree
    • Configure Module Properties
    • Connection Properties
    • Switch Configuration Properties
    • Port Configuration Properties
    • Advanced Port Properties
    • Port Thresholds (storm control)
    • Monitor and Reset the Switch
    • Switch Status
    • Port Status
    • Port Diagnostics
    • Cable Diagnostics
    • DHCP Pool Display
    • DHCP Address Assignment
    • Time Sync Configuration
    • Time Sync Information
    • Save and Restore Switch Configuration
  • 6 - Troubleshoot the Switch
    • IP Address Issues
    • Device Manager Web Interface Issues
    • Switch Performance
    • Access Direct Managed Mode
    • Restart or Reset the Switch
      • Restart the Switch from the Device Manager Web Interface
      • Restart the Switch from the Studio 5000 Environment
      • Reset the Switch to Factory Defaults
    • Recover the Switch Firmware and Restore Factory Defaults
    • Troubleshoot a Firmware Upgrade
  • A - Status Indicators
    • Switch Status Indicators
    • Dual-purpose Port Status Indicators
    • 10/100 Copper, 100BaseFX, and SFP Port Status Indicators
    • PoE Port Status Indicator
  • B - I/O Data Types
  • C - Port Assignments for CIP Data
  • D - Cables and Connectors
    • 10/100 and 10/100/1000 Ports
      • Connect to 10BASE-T- and 100BASE-TX-compatible Devices
    • 100BASE-FX Ports
    • SFP Transceiver Ports
    • Dual-purpose Ports
    • Console Port
    • Cable and Adapter Specifications
      • SFP Module Cable Specifications
      • PoE Port Cable Specifications
    • Adapter Pinouts
  • E - History of Changes
    • 1783-UM003H-EN-P, September 2013
    • 1783-UM003G-EN-P, December 2012
    • 1783-UM003F-EN-P, August 2011
  • Index
• Back Cover