Document Outline

• RuncoCare™ Standard Two Year Limited Warranty
• Important Safety Instructions
• Compliance Information
• 1. Introduction
  • 1.1 About This Manual
    • Target Audience
    • If You Have Comments About This Manual...
    • Textual and Graphic Conventions
      • Text Conventions
      • Graphic Conventions
  • 1.2 Using This Manual
  • 1.3 Description, Features and Benefits
    • Key Features and Benefits
    • Parts List
      • Optional Accessories
• 2. Controls and Functions
  • 2.1 VX-33i at a Glance
    • Figure 2-1 . VX-33i Front/Bottom/Side View
  • 2.2 VX-33i Rear Panel
    • Figure 2-2 . VX-33i Rear Panel
  • 2.3 VX-33i Rear Connector Panel
    • Figure 2-3 . Rear Connector Panel
  • 2.4 VX-33i Remote Control
    • Figure 2-4 . VX-33i Remote Control
• 3. Installation
  • 3.1 Remote Control
    • Notes on Batteries
    • Notes on Remote Control Operation
  • 3.2 Quick Setup
    • Table 3-1 . Installation Overview
  • 3.3 Installation Considerations
    • Installation Type
      • Table 3-2 . Projector Installation Options
    • Ambient Light
    • Throw Distance
      • Figure 3-1 . Estimating Throw Distance
      • Table 3-3 . VX-33i Lens Options and Throw Ratios
    • Vertical and Horizontal Position
      • Figure 3-2 . Projector Placement
    • Vertical and Horizontal Lens Shift
      • Figure 3-3 . Vertical Lens Shift (EXAMPLE ONLY)
      • Figure 3-4 . Horizontal Lens Shift (EXAMPLE ONLY)
      • Table 3-4 . VX-33i Vertical and Horizontal Lens Shift Limits
    • Folded Optics
      • Figure 3-5 . Folded Optics
    • Other Considerations
  • 3.4 Installing the Primary Projection Lens
  • 3.5 Installing the Optional CineWide Lens Mount
    • Installing the AutoScope Lens Motor (VX-33i/CineWide with AutoScope)
      • Figure 3-6 . VX-33i/CineWide with AutoScope Motor Assembly - Exploded View
      • Remove Projector Front Feet
      • Install Ceiling Mount Adapters/Projector Stands
        • Figure 3-7 . VX-33i with Ceiling Mount Adapters/Projector Stands
      • Install Lens Motor
        • Figure 3-8 . AutoScope Lens Motor Installation
    • Installing the Fixed CineWide Base Plate (VX-33i/CineWide)
      • Figure 3-9 . Installing the Fixed CineWide Base Plate
  • 3.6 Mounting the VX-33i
    • Floor Mounting (Upright)
    • Ceiling Mounting (Inverted)
    • Adjusting the Projection Angle
  • 3.7 Connections to the VX-33i
    • Connector Panel Access
    • Connecting Source Components to the VX-33i
      • HDMI Connections
        • Figure 3-10 . HDMI Source Connections
      • Digital (DTV) RGB or Component Video Connections
        • Figure 3-11 . Digital (DTV) RGB or Component Video Connections (HD1, HD2)
        • Figure 3-12 . Digital (DTV) RGB or Component Video Connections (HD3)
      • Analog (Computer) RGB Connections
        • Figure 3-13 . Analog RGB Connections
      • S-Video/Composite Video Connections
        • Figure 3-14 . S-Video and Composite Video Connections
    • RS-232 Controller Connection
      • Figure 3-15 . RS-232 Control System Connection
    • Connecting 12-volt Trigger Outputs to External Equipment
      • Figure 3-16 . 12-volt Trigger Output Connections
    • Connecting an External IR Receiver to the VX-33i
      • Figure 3-17 . External IR Receiver Connection
    • Connecting to AC Power
      • Projector
      • AutoScope Lens Motor
  • 3.8 Turning on the Power
  • 3.9 Adjusting the Picture Orientation
  • 3.10 Primary Lens Adjustments
    • Focus
    • Zoom
    • Vertical and Horizontal Lens Shift
  • 3.11 Installing and Adjusting the CineWide Anamorphic Lens
    • Attach Lens Mounting Assembly to Lens Motor Carriage Plate (CineWide with AutoScope) or Base Plate (fixed CineWide)
      • Figure 3-18 . VX-33i Anamorphic Lens Mounting Assembly - Exploded View
      • Figure 3-19 . Attaching the Anamorphic Lens to the Lens Adapter Ring
    • Configure Lens Motor Trigger
    • Adjust the Anamorphic Lens
      • Adjusting the Horizontal (X) Lens Position
      • Adjusting the Height (Y)
      • Pitch (Angle)
      • Adjusting the Yaw
      • Adjusting the Geometry
      • Focus
• 4. Operation
  • 4.1 Using the On-Screen Menus
    • Figure 4-1 . VX-33i OSD Menu Structure
    • Main Menu
    • Input Source
    • Aspect Ratio
      • Table 4-1 . Aspect Ratio Settings
    • Picture
      • Brightness
        • Figure 4-2 . Typical PLUGE Pattern for Adjusting Brightness
      • Contrast
        • Figure 4-3 . Typical Gray Bar Pattern for Adjusting Contrast
      • Color Saturation
        • Figure 4-4 . Typical Color Bar Pattern for Adjusting Color Saturation and Tint
      • Tint
      • Sharpness
        • Figure 4-5 . Typical Test Pattern for Adjusting Sharpness
    • Input Position
      • Left/Right
      • Up/Down
      • Width
      • Height
      • Overscan
      • Phase:
    • Memory Presets
    • Information
    • Calibration
      • ISF Night - Display Color
      • ISF Night - Input Image
      • ISF Night - Input Color
      • ISF Day - Display Color
      • ISF Day - Input Image
      • ISF Day - Input Color
      • Save ISF Settings
      • Output Shift
      • Splash Timer
      • OSD Position
    • Service
      • Test Video
      • Display Device
      • HD Format
      • Triggers
      • Miscellaneous
      • System Reset
      • Restore Saved Settings
• 5. Maintenance and Troubleshooting
  • 5.1 Lamp Replacement
  • 5.2 Filter Replacement
  • 5.3 Troubleshooting Tips
    • Table 5-1 . Troubleshooting Chart
• 6. Serial Communications
  • 6.1 RS-232 Connection and Port Configuration
    • If you are using a PC to communicate with the VX-33i
  • 6.2 Serial Command Syntax
    • Table 6-1 . Serial Commands and Responses
• 7. Specifications
  • 7.1 VX-33i Specifications
    • Table 7-1 . VX-33i Specifications
  • 7.2 VX-33i Dimensions
    • Figure 7-1 . VX-33i/CineWide with AutoScope Dimensions
  • 7.3 Supported Timings
    • Table 7-2 . Supported Signal Timings by Input