Document Outline

• Chapter 1 Safety
  • 1.1 USED CONVENTIONS
  • 1.2 LASER SAFETY
  • 1.3 DECLARATION OF CONFORMITY
  • 1.4 SCANNER LABELLING
• Chapter 2 General Description
  • 2.1 USE OF THE DISCOVERY SG-20
  • 2.2 CONSTRUCTION OF THE DISCOVERY SG-20
  • 2.3 FUNCTIONING OF THE DISCOVERY SG-20
    • 2.3.1 Introduction
    • 2.3.2 Input
    • The main input is generated by the integrated Scantech barcodereader, which is characterised by a high performance omnidirectional scan-performance. Additionally some commands or actions can be selected using the buttons next to the screen (depends on application).If required an additional handscanner or other serial-interface device can be attached (contact Scantech for details). 
    • 2.3.3 Output
    • 2.3.4 Software & control
• Chapter 3 Installation of the Discovery SG-20
  • 3.1 UNPACKING
  • 3.2 MOUNTING
    • 3.2.1 Mounting the bracket to the wall
    • 3.2.2 Placing the Discovery SG-20 on the bracket
• Chapter 4 System Integration
  • 4.1 INTERFACES
    • 4.1.1 Direct RS232 connection (single unit)
      • COMMUNICATION & TOOLS
      • INTERFACE SELECTION:
    • 4.1.2 Direct RS-422 connection (single unit)
      • COMMUNICATION & TOOLS
      • INTERFACE SELECTION:
      • Installing the separator box
    • 4.1.3 Multipoint RS485 network configuration
    • 4.1.4 Ethernet configuration
  • 4.2 INSTALLING THE DISCOVERY SG-20
    • 4.2.1 Removing the cover of the Discovery
    • 4.2.2 The Main Board
  • 4.3 SOFTWARE
    • 4.3.1 Software functionality
    • 4.3.2 Scantech Tools and Drivers
• Chapter 5 Configuring the Discovery
  • 5.1 TERMINAL CONFIGURATION USING 4 BUTTONS
  • 5.2 EXPLANATION OF THE SERVICE SCREENS
    • Screen 1.0
    • Screen 2.0
    • Screen 2.1
    • Screen 2.2
    • Screen 2.3
    • Screen 3.0
    • Screen 3.1
    • Screen 4.1
    • SG20 :
    • SG21 : (Only available with special SG21 firmware)
    • Screen 4.2
    • Screen 5.0
• Chapter 6 Ethernet Configuration
  • 6.1 ETHERNET NETWORK CONFIGURATION
    • 6.1.1 Preface
    • 6.1.2 Communication & Tools
    • 6.1.3 Interface Selection
  • 6.2 NETWORK PROTOCOLS
    • 6.2.1 INTERNET PROTOCOL (IP) ADDRESS
    • 6.2.2 ETHERNET (MAC) ADDRESS
    • 6.2.3 DHCP
  • 6.3 HOW TO GET IN TOUCH WITH AND TO CONFIGURE THE SG-20 DISCOVERY ETHERNET
    • 6.3.1 Making Connection
    • 6.3.2 Set the IP address of the individual terminal
    • 6.3.3 Checking the internal Discovery communication settings
    • 6.3.4 Set the Back-Office/Server IP address in the SG-20 terminal
  • 6.4 CONFIGURING THE DISCOVERY USING THE BUTTONS
  • 6.5 PHYSICAL CONNECTION
  • 6.6 Q & A , BASIC ETHERNET TROUBLESHOOTING
  • 6.7 STATUS LEDS
    • LED FUNCTIONS
  • 6.8 NON WINDOWS USERS
    • Making Connection
  • 6.9 RELATED DOCUMENTS
• Chapter 7 Maintaining the Discovery
  • 7.1 CLEANING
    • Introduction
    • Display messages
    • Display command characters
    • Introduction
    • Display programming examples
    • Example 1
    • Example 2
    • Example 3
    • Example 4
    • Example 5
    • Example 6
    • Example 7
    • Example 8
    • Screen 4.2
    • Bar Codes To Program the Scanner
    • H-1 GENERAL
    • H-2 I-START/ U-START AND THE SG-20 USER’S MANUAL
    • H-3 DRIVERS & OPERATING SYSTEMS
    • H-4 INTERFACES & CABLES
    • RS-485
    • RS-422
    • Ethernet
    • Wireless Networking, RFDC
    • H-6 SG-10 COMPATIBILITY
    • H-7 COMPETITIVE COMPATIBILITY
    • H-8 SETTINGS
    • H-9 BACK-OFFICE
    • H-10 HANDSCANNER SUPPORT
    • H-12 BARCODES
    • H-13 SERVICE
    • H-14 TECHNICAL QUESTIONS & ANSWERS
    • Scantech supplies:
    • The Distibutor / System Integrator supplies: