Document Outline

• Table of contents
• INTRODUCTION
• Chapter 1 PRODUCT SAFETY
  • 1.1 Safety & Caution
  • 1.2 FCC Warning
• Chapter 2 GENERAL DESCRIPTION
  • 2.1 Use of the V-1010BT
• Chapter 3 INSTALLATION OF THE V-1010BT
  • 3.1 V-1010BT Unpacking
  • 3.2 V-1010BT Cradle Installation
  • 3.3 V-1010BT Setup Bluetooth Communication
    • 3.3.1 Pairing
    • 3.3.2 Setup SPP Master Mode Communication
    • 3.3.3 Setup SPP Slave Mode Communication
    • 3.3.4 Setup HID Slave Mode Communication
    • 3.3.5 Sleep Mode
    • 3.3.6 Batch Mode
    • 3.3.7 Out of Range
• Chapter 4 CONFIGURING THE V-1010BT
  • 4.1 Preface
    • 4.1.1 Changing Scanner Settings with Programming Codes
    • 4.1.2 Programming Flow Chart
  • 4.2 Set All Default Parameter
  • 4.3 General Process
    • 4.3.1 Abort Configuration
    • 4.3.2 Recall
    • 4.3.3 Version Information
  • 4.4 CRADLE Interface Selection
    • 4.4.1 Interface
  • 4.5 Bluetooth Scanner Setup
    • 4.5.1 Preface
    • 4.5.2 Scanner Mode
    • 4.5.3 *** Batch Mode (“***” means “Quick Setting Label”, The function can be executed directly by scanning barcode instead of doing the general programming process.)
    • 4.5.4 Out of Range
    • 4.5.5 Sleep Mode
    • 4.5.6 Scanner Pincode Mode
    • 4.5.7 Scanner Pincode Setup
  • 4.6 Bluetooth Cradle Setup
    • 4.6.1 Cradle Pincode Mode
    • 4.6.2 Cradle Pincode Setup
  • 4.7 Scanner Operation
    • 4.7.1 Reading Mode
    • 4.7.2 Beeper Option
    • 4.7.3 Reading Level
    • 4.7.4 Accuracy Scan
    • 4.7.5 Sensitivity of Continuous Reading
    • 4.7.6 Reverse Output Characters
  • 4.8 RS232 Mode Parameters
    • 4.8.1 Baud Rate
    • 4.8.2 Data/Stop Bits
    • 4.8.3 Parity
    • 4.8.4 Handshaking
  • 4.9 Keyboard Wedge Mode Parameters
    • 4.9.1 Terminal Type
    • 4.9.2 Country/Language
    • 4.9.3 Upper/Lower Case
    • 4.9.4 Capslock Detection
    • 4.9.5 Character by ALT Method
    • 4.9.6 Select Numerical Pad
    • 4.9.7 Interscan Code Delay
  • 4.10 Output Characters
    • 4.10.1 Select Terminator
  • 4.11 Code Type
    • 4.11.1 Barcode Selection
  • 4.12 UPC/EAN/JAN Parameters
    • 4.12.1 Reading Type
    • 4.12.2 Supplemental Setup
    • 4.12.3 Check Digit Transmission
  • 4.13 Code 39 Parameters
    • 4.13.1 Type of Code
    • 4.13.2 Check Digit Transmission
    • 4.13.3 Output Start/Stop Character
    • 4.13.4 Decode Asterisk
    • 4.13.5 Setup Code Length
  • 4.14 Code 128 Parameters
    • 4.14.1 Reading Type
    • 4.14.2 Check Digit Transmission
    • 4.14.3 Append FNC2
    • 4.14.4 Setup Code Length
  • 4.15 Interleave 2 of 5 Parameters
    • 4.15.1 Check Digit Transmission
    • 4.15.2 Setup Number of Character
    • 4.15.3 Brazilian Banking Code
    • 4.15.4 Setup Code Length
  • 4.16 Industrial 2 of 5 Parameters
    • 4.16.1 Reading Type
    • 4.16.2 Check Digit Transmission
    • 4.16.3 Setup Code Length
  • 4.17 Matrix 2 of 5 Parameters
    • 4.17.1 Check Digit Transmission
    • 4.17.2 Setup Code Length
  • 4.18 CODABAR/NW7 Parameters
    • 4.18.1 Setup Start/Stop Characters upon Transmission
    • 4.18.2 Transmission Type of Start/Stop
    • 4.18.3 Setup Code Length
  • 4.19 Code 93 Parameters
    • 4.19.1 Check Digit Transmission
    • 4.19.2 Setup Code Length
  • 4.20 Code 11 Parameters
    • 4.20.1 Check Digit Transmission
    • 4.20.2 Setup Code Length
  • 4.21 MSI/Plessey Code Parameters
    • 4.21.1 Check Digit Transmission
    • 4.21.2 Setup Code Length
  • 4.22 Telepen Parameters
    • 4.22.1 Type of Code
    • 4.22.2 Check Digit Transmission
    • 4.22.3 Setup Code Length
  • 4.23 GS1 Databar Omnidirectional Parameters
    • 4.23.1 Check Digit Transmission
    • 4.23.2 Application ID
    • 4.23.3 Symbology ID
  • 4.24 GS1 Databar Limited Parameters
    • 4.24.1 Check Digit Transmission
    • 4.24.2 Application ID
    • 4.24.3 Symbology ID
  • 4.25 GS1 Databar Expanded Parameters
    • 4.25.1 Symbology ID
• Chapter 5 MISCELLANEOUS PARAMETERS
  • 5.1 Bar Code ID
    • 5.1.1 Default Barcode ID
    • 5.1.2 User Define Code ID
  • 5.2 Preamble and Postamble Insertion
    • 5.2.1 Setup Insertion
    • 5.2.2 Insertion Set Number
    • 5.2.3 Code Type for Insertion
    • 5.2.4 Position to Be Inserted
    • 5.2.5 Characters to Be Inserted
  • 5.3 Character Deletion
    • 5.3.1 Deletion Set Number
    • 5.3.2 Code Type for Deletion
    • 5.3.3 Position to Be Deleted
    • 5.3.4 Number of Characters to Be Deleted
• APPENDIXES
  • A. Decimal Value Table
  • B. ASCII Value Table
  • C. ASCII Table
  • D. Function Key Table
  • C. Technical Specifications
  • D. Scan Map
  • E. LED Indicator Status
  • F. Test Symbologies
  • G. Quick Configuration