Document Outline

• WARNING
• MAINTENANCE AGREEMENT
• CUSTOMER RESPONSIBILITIES
• OOLS REQUIRED FOR ASSEMBLY
• TO REMOVE BRUSHWACKER FROM CARTON
• WARNING:
• HOW TO ASSEMBLE YOUR BRUSHWACKER
  • HANDLEBAR ASSEMBLY (See Fig. 1)
  • THROTTLE HANDLE ASSEMBLY (See Fig. 2 )
  • (See Flg.3)
• CUTTING LINE HEAD CONFIGURATION
  • INSTALLING UNE LnSIlTERjONTa PLASTIC UNE TRIMMER SHIELD (See Fig. 4)
  • PRE-INSTALLATION
  • INSTALLING THE PLASTIC UNE TRIMMER SHIELD (See Fig. 5)
  • INSTALLING THE DUAL UNE HEAD (See Fig. 6 & 7 }
  • RE-INSTALLATION
  • ISTALUNG THE METAL BLADE SHIELD iee Fig. 8 )
  • BLADE TRANSPORT/STORAGE COVER (See Figure 9)
  • INSTALLING THE BRUSH TRI-BLADE (S^ Fig. 10 & 11)
• SAW BLADE CONFIGURATION
  • PRE-INSTALLATION
  • INSTALUNG THE SAW BLADE (See Fig. 12,13, & 14 )
  • CHECKLIST
• KNOW YOUR BRUSHWACKER (See Fig. 16)
  • STOPPING YOUR ENGINE
    • SHOULDER HARNESS (Fig. 16)
    • ii^LEBAR ADJUSTMENT (Figure 18 )
    • THROTTLE TRIGGER & LOCKOUT (Fig. 19)
• ÎLADE SAFETY
• WARNING
• 11
  • PERATOR SAFETY
  • HT SAFETY
  • CUTTING SAFETY
• BLADE SAFETY
  • WHAT CAUSES BLADE THRUST?
  • WHEN DOES BLADE THRUST OCCUR?
  • REDUCE THE CHANCE OF BLADE THRUST
  • OPERATING/USE TIPS (Figure 20)
• UNE TRIMMER SAFETY
• WARNING:
  • OPERATOR SAFETY
  • CUTTING SAFETY
  • UNIT SAFETY
• DIMMER LINE ADVANCE (Fig. 21 )
  • 1g. 22,23,24,25, & 26)
• WARNING:
• BEFORE STARTING ENGINE:
  • GASOLINE
  • FUEL STABILIZER
  • 2-CYCLE OIL:
  • GASOUNE AND OIL MI3tTURE
  • FUEL MIXTURE CHART
• TOPPING YOUR ENGINE
• TARTING YOUR ENGINE (Fig. 27)
• WARNING:
  • SFORE STARTING THE ENGINE:
  • 'ARTING A COLD ENGINE OR WARM ENGINE AFTER RUNNING OUT OF FUEL:
  • STARTING A WARM ENGINE THAT HAS NOT RUN OUT OF FUEL
  • STARTING A FLOODED ENGINE:
• MAINTENANCE SCHEDULE
• GENERAL RECOMMENDATIONS
  • CLEAN UNIT AND LABELS
• BEFORE EACH USE
  • CHECK FOR DAMAGED/WORN PARTS
  • LUBRICATION CHART (Fig. 28)
• WARNING
  • iECK FOR LOOSE FASTENERS/PARTS
  • CCK GEAR BOX LUBRICATION 29 )
  • EAN AIR FILTER (Fig. 30 )
  • REPLACE SPARK PLUG (Fig. 31 )
  • INSPECT MUFFLER AND
  • SPARK ARRESTOR SCREEN (IF INSTALLED)
• DUAL LINE REPLACEMENT
  • INSTALLING SPOOL WITH UNE ALREADY WOUND (Fig. 32,33,34,35, & 36 )
• ILADE SHARPENING
  • BRUSH TRI-BLADE SHARPENING (Fig. 37)
  • SAW BLADE SHARPENING (Fig. 38)
  • CARBURETOR PRESETS (Fig. 39)
• ADJUSTING PROCEDURE
  • IDLE SPEED ADJUSTMENT
  • LOW SPEED MIXTURE ADJUSTMENT
  • HIGH SPEED MIXTURE ADJUSTMENT
  • ACCELERATION CHECK
• WARNING:
  • AS TRIMMER/BRUSHCUTTER STORAGE JNSTRUCTIONS
  • ENGINE
  • OTHER
• TROUBLE SHOOTING CHART
• SEAES BEUSHWACKER™ - MODEL 368.798280
• SEARS BRUSHWACKER™ - MODEL 358.798280
• SEARS BRUSHWACKER™ - MODEL 358,798280
• SEARS BR0SHWACKER"- - MODEL 3S8.798280 CARBURETOR ASSY. - PART NO. 503-281505
• SEARS BRUSHWACiOER“ - MODEL 358.798280
• CRflFTSMflN^
  • Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA