Document Outline

• 1.0 INTRODUCTION
  • 1.1 DESCRIPTION OF THE MACHINE
  • 1.2 ILLUSTRATION OF THE MACHINE
  • 1.3 MACHINE SERIAL NUMBER
• 2.0 SAFETY
  • 2.1 SAFETY ALERT SYMBOL
    • 2.1.1 Signal Words
  • 2.2 OPERATOR RESPONSIBILITY
    • 2.2.1 Key Safety Reminders:
  • 2.3 GENERAL SAFETY PRACTICES
  • 2.4 MAINTENANCE SAFETY
  • 2.5 HYDRAULIC SAFETY
  • 2.6 TRANSPORT SAFETY
  • 2.7 STORAGE SAFETY
  • 2.8 TIRE SAFETY
  • 2.9 SAFETY SIGNS
    • 2.9.1 Applied Safety Signs
    • 2.9.2 Safety Sign Information
• 3.0 SPECIFICATIONS
  • 3.1 HARDWARE TORQUE
    • 3.1.1 SAE
    • 3.1.2 Metric
    • 3.1.3 Flare-Type Tube Fittings
    • 3.1.4 Tire Torque
  • 3.2 TIRE PRESSURE
  • 3.3 TRACTOR REQUIREMENTS
  • 3.4 XL SERIES TOOLBAR 10"
  • 3.5 XL SERIES TOOLBAR 12"
  • 3.6 XL SERIES TOOLBAR 15"
  • 3.7 45 SERIES TOOLBAR 10”
  • 3.8 45 SERIES TOOLBAR 12”
  • 3.9 45 SERIES TOOLBAR 15”
  • OPENERS
    • 3.10.1 Quick Pin Opener
    • 3.10.2 SEED DEPTH
• 4.0 OPERATION
  • 4.1 FIELD OPERATION
    • 4.1.1 Operator Responsibility
  • 4.2 TRACTOR HOOK UP
    • 4.2.1 Shank lift and lower (Two hoses with red bands)
    • 4.2.2 Hydraulic Manifold (Two hoses with green bands)
    • 4.2.3 Case Drain(s) (One hose with yellow band)
  • 4.3 HYDRAULIC HOSE HOOK UP
  • 4.4 HYDRAULIC MANIFOLD DESCRIPTION
  • 4.5 PRE-OPERATION CHECKLIST
  • 4.6 WINGING THE 7-PLEX MACHINE DOWN
  • 4.7 PRIMARY OPERATION
  • 4.8 PRIMARY OPERATION VARIABLES
    • 4.8.1 Packer Tire Pressure
    • 4.8.2 Field Travel Speed
    • 4.8.3 Packing and Trip Pressure
    • 4.8.4 Packing and Trip Pressure Tips:
    • 4.8.5 Mud Scraper Adjustment
    • Cornering
    • 4.8.7 Furrow Depth and Width
    • 4.8.8 Knife Lateral Separation
  • 4.9 SUPPLY AND DROP TUBES
    • Basic Configuration
    • Range Of Knife Configurations
    • 4.9.3 Twin Wing
  • CROP RESIDUE CONSIDERATIONS
  • 4.11 SEED HAWK PACKER TIRE
    • 4.11.1 Loose Soil Conditions
    • 4.11.2 Muddy Soil Conditions
    • 4.11.3 Operating on Curves and Corners
    • 4.11.4 Low Packer Tire Pressure
  • 4.12 SIDE BANDING WITH ANHYDROUS AMMONIA WHILE SEEDING
  • 4.13 DROP TUBE EXTENSION with NH3
  • 4.14 PLACING PHOSPHATE FERTILIZER WITH SEED
• 5.0 LIQUID SYSTEM OPERATION
  • 5.1 SYSTEM FLOW DESCRIPTION
  • 5.2 CHECKING FERTILIZER RUNS
  • VARIABLE RATE LIQUID CHART
• 6.0 SBR HITCH
  • 6.1 REQUIREMENTS
  • 6.2 BENEIFITS
• 7.0 MAINTENANCE
  • 7.1 HYDRAULIC CARTRIDGES
  • 7.2 HYDRAULIC CYLINDERS
  • 7.3 CASTER WHEEL GREASE FITTINGS
  • 7.4 CASTER WHEEL PLATE GAP
  • 7.5 WHEEL HUBS & CASTER PLATES
    • Main Frame Wheel Hubs & Castor Plates
    • Wing Hubs
    • 7.5.3 Packer Wheel Hubs
    • 7.5.4 Wing Hinge Points
  • 7.6 SEED/FERTILIZER KNIVES
  • 7.7 MAINTENANCE SCHEDULE
• 8.0 TROUBLE-SHOOTING
• SCHEMATICS
  • 9.1 2 STATION HYDRAULIC MANIFOLD (2012)
  • 9.2 XL SERIES 5 PLEX MAIN HYDRAULICS (2012)
  • 9.3 XL SERIES 71’8” – 10 & 72’ – 12 MAIN HYDRAULICS (2012)
  • 9.4 XL SERIES 80’ & 84’ MAIN HYDRAULICS W/INTENSIFIER (2012)
  • 9.5 30’ 45 SERIES HYDRAULICS (2012)
  • 9.6 40’/50’/60’ 45 SERIES HYDRAULICS (2012)
  • 9.7 XL SERIES 5 PLEX SCT HYDRAULICS (TBT) (2012)
  • 9.8 XL SERIES 5 PLEX SCT HYDRAULICS (TBH) (2012)
  • 9.9 XL SERIES 7 PLEX SCT HYDRAULICS (TBT) (2012)
  • XL SERIES 7 PLEX SCT HYDRAULICS (TBH) (2012)
  • 9.11 50’/60’ 45 SERIES SCT HYDRAULIC (TBT) (2012)
  • 9.12 50’/60’ 45 SERIES SCT HYDRAULICS (TBH) (2012)
  • 9.13 OPENER HYDRAULICS FOR SCT TOOLBARS (2012)
  • 9.14 SEED BETWEEN ROW HYDRAULICS
  • 9.15 SEED BETWEEN ROW HYDRAULIC MODEL
  • 9.16 CONTROL BOX (SWITCH BOX)
  • 9.17 TOOL BAR WIRING HARNESS
• 10.0 WARRANTY
• 11.0 NOTES
• 12.0 INDEX