Document Outline

• 1. Installation and Basic Operation
  • 1.1 Unpacking Your Indicator
  • 1.2 Dimensions Front Views
  • 1.3 Dimensions – Side Views
  • 1.4 Step 1: Installation
    • 1.4.1 Panel Mounting the Indicator
    • 1.4.2 Panel Cut-out Sizes
    • 1.4.3 Recommended Minimum Spacing of Indicators
    • 1.4.4 To Remove the Indicator from its Sleeve
  • 1.5 Step 2: Wiring
  • 1.6 Terminal Layout Series 3L Indicators
  • 1.7 Wire Sizes
  • 1.8 Sensor Input (Measuring Input)
  • 1.9 Outputs
    • 1.9.1 Output 1 & Output 3
    • 1.9.2 AA Relay Form C (FM Approved)
    • 1.9.3 Transmitter Supply
    • 1.9.4 Digital Inputs A and B
  • 1.10 Indicator Power Supply
  • 1.11 Digital Communications (Optional)
• 2. Safety and EMC Information
  • 2.1 Installation Safety Requirements
• 3. Switch On
  • 3.1 New Indicator
    • 3.1.1 To Re-Enter Quick Code Mode
  • 3.2 Pre-Configured Indicator or Subsequent Starts
  • 3.3 Front panel layout
    • 3.3.1 Alarm Indication
    • 3.3.2 Out of Range Indication
    • 3.3.3 Sensor Break Indication
  • 3.4 Operator Parameters in Level 1
• 4. Operator Level 2
  • 4.1 To Enter Level 2
    • 4.1.1 To Return to Level 1
  • 4.2 Level 2 Parameters
  • 4.3 FM and Alarm Units
  • 4.4 Recipes
• 5. Access to Further Parameters
  • 5.1 Level 3
  • 5.2 Configuration Level
    • 5.2.1 To Select Access Level 3 or Configuration Level
  • 5.3 Parameter lists
    • 5.3.1 To Choose Parameter List Headers
    • 5.3.2 To Locate a Parameter
    • 5.3.3 How Parameters are Displayed
    • 5.3.4 To Change a Parameter Value
    • 5.3.5 To Return to the HOME Display
    • 5.3.6 Time Out
  • 5.4 Navigation Diagram
  • 5.5 Access Parameters
• 6. Process Input
  • 6.1 Process Input Parameters
    • 6.1.1 Input Types and Ranges
    • 6.1.2 Units
    • 6.1.3 PV Offset
      • 6.1.3.1 Example: To Apply an Offset:-
    • 6.1.4 PV Input Scaling
      • 6.1.4.1 Example: To Scale a Linear Input
• 7. Input/Output Channels
  • 7.1 Output Channel 1 (OP-1) – Series 3L Indicators
    • 7.1.1 Sense
    • 7.1.2 Source
    • 7.1.3 Power Fail
    • 7.1.4 Example: To Configure OP-1 Relay to Operate on Alarms 1 and 2:-
  • 7.2 Output Channel 3 (OP-3) – Series 3L Indicators
    • 7.2.1 Sense
    • 7.2.2 Source
    • 7.2.3 Power Fail
    • 7.2.4 Example: To Configure OP-3 Relay to Operate on Alarms 1 and 2:-
  • 7.3 AA Relay Channel (AA) (Output 4 FM Relay)
• 8. Digital Inputs
  • 8.1 Digital Input Parameters
• 9. Alarms
  • 9.1 Types of Alarm
    • 9.1.1 Alarm Relay Output
    • 9.1.2 Alarm Indication
    • 9.1.3 To Acknowledge An Alarm
  • 9.2 Behavior of Alarms After a Power Cycle
    • 9.2.1 Example 1
    • 9.2.2 Example 2
    • 9.2.3 Example 3
  • 9.3 Alarm Parameters
    • 9.3.1 Example: To Configure Alarm 1
  • 9.4 Diagnostic Alarms
• 10. Recipe
• 11. Digital Communications
  • 11.1 Digital Communications Wiring
    • 11.1.1 EIA 485
  • 11.2 Digital Communications Parameters
    • 11.2.1 Broadcast Communications
    • 11.2.2 Broadcast Master Communications
    • 11.2.3 Wiring Connections
  • 11.3 Example: To Set Up Instrument Address
  • 11.4 DATA ENCODING
  • 11.5 Parameter Modbus Addresses
• 12. Calibration
  • 12.1 To Check Input Calibration
    • 12.1.1 Precautions
    • 12.1.2 To Check mV Input Calibration
    • 12.1.3 To Check Thermocouple Input Calibration
    • 12.1.4 To Check RTD Input Calibration
  • 12.2 Offsets
    • 12.2.1 Five Point Offset
  • 12.3 Input Calibration
    • 12.3.1 To Calibrate mV Range
    • 12.3.2 To Calibrate Thermocouple Ranges
    • 12.3.3 To Calibrate RTD Ranges
  • 12.4 Calibration Parameters
• 13. TECHNICAL SPECIFICATION
• 14. Parameter Index
• 15. Revision History