Document Outline

• Flomat_MX4_Instructions_Manual
  • FLOMAT-FX SENSOR
  • 1. WORKING PRINCIPLE
  • 2. RECEPTION
    • 2.1 Unpacking
    • 2.2 Storage temperatures
  • 3. HANDLING
  • 4. INSTALLATION
    • 4.1 Sensor position
    • 4.2 Straight pipe sections
      • 4.2.1 Mixtures
    • 4.3 Valves
    • 4.4 Pumps
    • 4.5 Aeration
    • 4.6 Vibrations
    • 4.7 Magnetic fields
    • 4.8 Temperature
  • 5. MOUNTING
    • 5.1 Insert mounting
    • 5.2 Sensor mounting
    • 5.3 Tightening torque
    • 5.4 Electronic converter connection
    • 5.5 Electronic converter programming
  • 6. MAINTENANCE
  • MX4 CONVERTER
  • 1. INTRODUCTION
  • 2. INSTALLATION
    • 2.1 Sensor connection
      • 2.1.1 Compact converter
      • 2.1.2. Remote converter
    • 2.2 Electrical connection
      • 2.2.1 Power supply wiring
      • 2.2.2. Relay output wiring
      • 2.2.3 Remote reset input wiring
      • 2.2.4 Analog output wiring
      • 2.2.5 Pulse output wiring
  • 3. REMOTE SENSOR
    • 3.1 Preparing the cable
    • 3.2 Cable installation
    • 3.3 Cable connection to sensor
    • 3.4 Cable connection to converter
    • 3.5 Cable specifications
  • 4. CONVERTER INTERFACE
  • 5. MAIN MENU
    • 5.1 Passwords to access the menus
  • 6. INSTALLATION PARAMETERS
    • 6.1 Language
    • 6.2 Sensor factor
    • 6.3 Converter factor
    • 6.4 Nominal diameter
    • 6.5 Diagnosis
      • 6.5.1 Parameters
      • 6.5.2 Simulator
      • 6.5.3 Mains frequency
      • 6.5.4 Coil current
  • 7. CONVERTER PROGRAMMING
    • 7.1 Language
    • 7.2 Units
    • 7.3 Flow rate decimals
    • 7.4 Flow rate
      • 7.4.1 Empty pipe
      • 7.4.2 Cut off
      • 7.4.3 Reversal flow rate
      • 7.4.4 Damping
      • 7.4.5 Offset
    • 7.5 Outputs
      • 7.5.1 Relay 1 and relay 2
        • 7.5.1.1 Alarm
        • 7.5.1.2 Empty pipe
        • 7.5.1.3 Negative flow
      • 7.5.2 Pulse output
        • 7.5.2.1 Pulse output configuration
        • 7.5.2.2 Units
        • 7.5.2.3 Pulses
        • 7.5.2.4 Duty cicle
      • 7.5.3 Analog output
        • 7.5.3.1 4-20 mA output configuration
        • 7.5.3.2 Programming of the 4-20 mA output
        • 7.5.3.3 Current calibration for 4 and 20 mA
    • 7.6 Default screen
    • 7.7 Totalizer
    • 7.8 Modbus
  • 8. SERIAL NUMBER
  • 9. SOFTWARE VERSION
  • 10. WORKING SCREEN
  • 11. MAINTENANCE
    • 11.1 Fuse
  • 12. ASSOCIATED SOFTWARE WINSMETER MX4
    • 12.1 USB cable connection and drivers installation
    • 12.2 Port connection
    • 12.3 Access to installation and programming
    • 12.4 Visualization
    • 12.5 Firmware updates
  • 13. TECHNICAL CHARACTERISTICS
  • 14. DIMENSIONS
  • 15. TROUBLESHOOTING
  • ANNEX A - Flow rate diagram