Document Outline

• MMT310 User's Guide
  • Table of Contents
  • GENERAL INFORMATION
    • About This Manual
      • Contents of This Manual
      • Version Information
      • Related Manuals
      • Documentation Conventions
    • Safety
      • ESD Protection
    • Recycling
    • Regulatory Compliances
      • Emissions
      • Immunity
    • Trademarks
    • Software License
    • Warranty
  • PRODUCT OVERVIEW
    • Introduction to MMT310 Series
      • MMT310 Transmitter Parts
      • Probe Options
      • Filter Options
  • INSTALLATION
    • Mounting
      • Selecting a Place for the Probe
      • Mounting the Transmitter/Removing the Transmitter Unit
      • Mounting the Transmitter with Optional Rain Shield
      • Mounting the Rain Shield with Larger Transmitter Mounting Plate
      • Mounting the MMT318
      • Mounting for Pressurized Pipelines/Oils
        • Tightening the Clasp Nut
      • Ball Valve Installation Kit for MMT318
      • Sampling Cell for MMT318
      • Mounting the MMT317
        • MMT317 Probe with Swagelok Connector for Tight-place Installations
    • Connections
      • Cable Wiring
    • Power Supply Requirements
  • OPERATION
    • Power Supply
    • Transmitter Start-Up
    • Serial Line and Analog Communication Options
      • RS-232 Serial Port Connection
      • USB Connection
        • Installing the Driver for the USB Cable
      • Connection to an MI70 Hand-held Indicator
    • Terminal Program Settings
      • Opening a Serial/USB Connection with PuTTY
    • List of Serial Commands
    • Measurement Output
      • Starting the Continuous Reading Output
      • Stopping the Continuous Reading Output
      • Set Continuous Output Interval for RUN Mode
      • Output Reading Once
      • Set Serial Interface Mode
      • Serial Line Settings
      • Set Transmitter Address for Use in POLL Mode
      • Temporarily Open Transmitter from POLL Mode to Receive Serial Commands
      • Set Transmitter in POLL Mode
    • Output Formatting
      • Set Serial Output Format
      • Set Time and Date
      • Add Time and Date to SEND and R Outputs
      • Select Metric or Nonmetric Output Units
    • Setting, Scaling and Testing the Analog Outputs
      • Set Analog Outputs
      • Select Parameter for Analog Outputs
      • Scale Analog Outputs
      • Test Analog Outputs
      • Test Analog Outputs for Desired Readings
      • Set Error Outputs
    • Other Commands
      • Check Transmitter Settings
      • Serial Bus Echo
      • All Devices in POLL Mode Send Their Addresses
      • List Commands
      • Set Result Filtering
      • Reset Transmitter
      • Display Error Messages
  • MAINTENANCE
    • Periodic Maintenance
      • Calibration Interval
    • Replacing Consumables
      • Changing the Filter
      • Changing the Sensor
    • Clean the Sensor Before Storing the Transmitter
    • Technical Support
    • Product Returns
  • CALIBRATION AND ADJUSTMENT
    • Preparations Before the Calibration
    • Relative Humidity Calibration and Adjustment (in Two Points)
      • Low End Adjustment
      • High End Adjustment
      • Temperature Calibration and Adjustment (in One Point)
      • Revert Factory Calibration
      • View Current Offset and Gain Adjustment
      • Relative Humidity Calibration after Sensor Change
      • Set Calibration Information Text
      • Set Calibration Date
      • Analog Output Calibration
    • Adjustment Using an MI70 Indicator
      • Starting MI70 Adjustment
      • Adjusting RH with MI70
        • 1-point RH Adjustment
        • 2-point RH Adjustment
        • LiCl – NaCl Automatic Adjustment
      • Adjusting T with MI70
        • 1-point T adjustment
        • 2-point T adjustment
      • Environment Settings
      • Last Adjustment Date
  • TECHNICAL DATA
    • Specifications
    • Spare Parts and Accessories
    • Dimensions in mm (inches)
      • Transmitter Enclosure and Mounting Plates
      • Rain Shield Dimensions
      • MMT318 Probe Dimensions
      • Ball Valve Set Dimensions
      • MMT317 Probe with Optional Swagelok Connector, Dimensions
  • APPLICATIONS
    • Transformer Oils
      • PPM Calculation for Transformer Oils
      • Calculation Model with Average Coefficients
      • Calculation Model with Oil Specific Coefficients
    • PPM Calculation Setting
      • Calculation Setting (Calculation Model with Average Coefficients)
      • Changing the Calculation Coefficients (Calculation Model with Oil Specific Coefficients)
        • Technical Data
    • Paper Machine Application