Document Outline

• CONTENTS
  • Introduction
    • ■ Notes on the User’s Manual
    • ■ For Safe Use of Product
    • ■ Warranty
    • ■ Trade Mark
    • ■ ATEX Documentation
  • 1. Notes on Handling
    • 1.1 Nameplate
    • 1.2 Transport
    • 1.3 Storage
    • 1.4 Choosing the Installation Location
    • 1.5 Use of a Transceiver
    • 1.6 Insulation Resistance Test and Withstand Voltage Test
    • 1.7 Notes for Saftey
    • 1.8 EMC Conformity Standards
    • 1.9 Installation of Explosion Protected Type Positioner
      • 1.9.1 FM Certification
      • 1.9.2 ATEX Certification
      • 1.9.3 CSA Certification
      • 1.9.4 TIIS Certification
  • 2. Part Names
    • 2.1 Appearance and Part Names
    • 2.2 Block Diagram
  • 3. Installing YVP110 on Actuator
    • 3.1 General
    • 3.2 Installing YVP110 on Actuator
      • 3.2.1 Installing YVP110 on Linear-motion Control Valve
      • 3.2.2 Installing YVP110 on Rotary-motion Control Valve
      • 3.2.3 A/M Switching
  • 4. Wiring and Piping
    • 4.1 General
    • 4.2 Piping
      • 4.2.1 Air Supply
      • 4.2.2 Pneumatic Piping
    • 4.3 Wiring
      • 4.3.1 Recommended Cables
      • 4.3.2 Precautions on Wiring
    • 4.4 Grounding
  • 5. Setup
    • 5.1 General
    • 5.2 Setting Basic Parameters
    • 5.3 Carrying out Tuning
    • 5.4 Checking Valve Actions
    • 5.5 Setting Parameters of Transducer Block
  • 6. Maintenance
    • 6.1 General
    • 6.2 Periodic Inspections
      • 6.2.1 Cleaning the Fixed Nozzle
    • 6.3 Part Replacement
      • 6.3.1 Replacing the Control Relay Assembly
      • 6.3.2 Replacing the Screen Filters
      • 6.3.3 Replacing the Internal Air Filter
      • 6.3.4 Tuning the Pressure Balance of Control Relay
  • 7. Standard Specifications
  • 8. About Fieldbus
    • 8.1 Outline
    • 8.2 Internal Structure of YVP110
      • 8.2.1 System/network Management VFD
      • 8.2.2 Function Block VFD
    • 8.3 Logical Structure of Each Block
    • 8.4 System Configuration
      • 8.4.1 Connection of Devices
    • 8.5 Integration of DD
  • 9. Configuration
    • 9.1 Network Design
    • 9.2 Network Definition
    • 9.3 Definition of Combining Function Blocks
    • 9.4 Setting of Tags and Addresses
    • 9.5 Communication Setting
      • 9.5.1 VCR Setting
      • 9.5.2 Function Block Execution Control
    • 9.6 Block Setting
      • 9.6.1 Link Object
      • 9.6.2 Trend Object
      • 9.6.3 View Object
      • 9.6.4 Function Block Parameters
  • 10. Actions of YVP110 During Operation
    • 10.1 Block Modes
    • 10.2 Alarm Generation
    • 10.3 Simulation Function
  • 11. Resource Block
    • 11.1 General
    • 11.2 Alarm Processing
    • 11.3 Device Status
  • 12. Transducer Block
    • 12.1 General
    • 12.2 Forward Path
      • 12.2.1 Input from AO Block
      • 12.2.2 Position-to-flow Rate Characteristic Conversion
      • 12.2.3 FINAL_VALUE and Range
      • 12.2.4 Tight-shut and Full-open Actions
    • 12.3 Backward Path
      • 12.3.1 FINAL_POSITION_VALUE
      • 12.3.2 Limit Switches
    • 12.4 Auto Tuning
    • 12.5 Travel Calibration
    • 12.6 Online Diagnostics
      • 12.6.1 XD_ERROR
      • 12.6.2 Fail-safe Action
      • 12.6.3 Operation Result Integration
      • 12.6.4 Recording of Revisions
    • 12.7 Control Parameters
    • 12.8 Temperature and Pressure Measurement
  • 13. AO Function Block
    • 13.1 General
    • 13.2 Modes
    • 13.3 Forward Path
      • 13.3.1 Fault state
    • 13.4 Backward Path
    • 13.5 IO_OPTS and STATUS_OPTS
    • 13.6 Mode Shedding upon Computer Failure
    • 13.7 Initialization at Start
    • 13.8 Alarm Processing
  • 14. DI Function Block
    • 14.1 General
    • 14.2 Modes
    • 14.3 PV Value (PV_D)
    • 14.4 Filtering
    • 14.5 Output
    • 14.6 IO_OPTS and STATUS_OPTS
    • 14.7 Alarm Processing
      • 14.7.1 Block Alarms
      • 14.7.2 Discrete Alarm
  • 15. OS Function Block
    • 15.1 General
    • 15.2 Modes
    • 15.3 Output Processing
    • 15.4 Backward Path (BKCAL_OUT)
    • 15.5 STATUS_OPTS
    • 15.6 Alarm Processing
  • 16. PID Function Block
    • 16.1 General
    • 16.2 Modes
    • 16.3 Input Processing
    • 16.4 Setpoint (SP) Limiters
    • 16.5 PID Computation
    • 16.6 Control Output
    • 16.7 Direction of Control Action
    • 16.8 Control Action Bypass
    • 16.9 Feed-forward
    • 16.10 External-output Tracking (LO)
    • 16.11 Measured-value Tracking
    • 16.12 CONTROL_OPTS
    • 16.13 Initialization and Manual Fallback (IMan)
    • 16.14 Manual Fallback
      • 16.14.1 STATUS_OPTS
    • 16.15 Auto Fallback
    • 16.16 Mode Shedding upon Computer Failure
    • 16.17 Alarms
      • 16.17.1 Block Alarm (BLOCK_ALM)
      • 16.17.2 Process Alarms
  • 17. IS Function Block
    • 17.1 IS Function Block Schematic
    • 17.2 Input Section
      • 17.2.1 Mode Handling
      • 17.2.2 MIN_GOOD Handling
    • 17.3 Selection
      • 17.3.1 OP_SELECT Handling
      • 17.3.2 SELECTION Handling
    • 17.4 Output Processing
      • 17.4.1 Handling of SELECTED
      • 17.4.2 OUT Processing
      • 17.4.3 STATUS_OPTS
    • 17.5 Application Example
  • 18. AR Function Block
    • 18.1 AR Function Block Schematic
    • 18.2 Input Section
      • 18.2.1 Main Inputs
      • 18.2.2 Auxiliary Inputs
      • 18.2.3 INPUT_OPTS
      • 18.2.4 Relationship between the Main Inputs and PV
    • 18.3 Computation Section
      • 18.3.1 Computing Equations
      • 18.3.2 Compensated Values
      • 18.3.3 Average Calculation
    • 18.4 Output Section
      • 18.4.1 Mode Handling
      • 18.4.2 Status Handling
  • 19. Diagnostics
    • 19.1 Overview
    • 19.2 Integration Functions
    • 19.3 Signature Measurement Functions
      • 19.3.1 Signature Measurement Procedure
      • 19.3.2 Signatures and Relevant Parameters
      • 19.3.3 Signature Measuring Result
  • 20. Troubleshooting
    • 20.1 What to Do First
    • 20.2 Troubleshooting Communications
    • 20.3 Troubleshooting Function Block Parameters
    • 20.4 Troubleshooting Valve Control
    • 20.5 Troubleshooting Auto Tuning
    • 20.6 Troubleshooting Position, Pressure, and Temperature Sensors
  • Appendix 1. Function Block Parameters
    • A1.1 Parameters of Resource Block
    • A1.2 Parameters of Transducer Block
    • A1.3 Parameters of AO Block
    • A1.4 Parameters of DI Block
    • A1.5 Parameters of OS Block
    • A1.6 Parameters of PID Block (Optional)
    • A1.7 Parameters of IS Block
    • A1.8 Parameters of AR Block
    • A1.9 IO_OPTS - Availability of Options for Each Block
    • A1.10 STATUS_OPTS - Availability of Options for Each Block
    • A1.11 CONTROL_OPTS - Availability of Options for Each Block
  • Appendix 2. Link Master Functions
    • A2.1 Link Active Scheduler
    • A2.2 Link Master
    • A2.3 Transfer of LAS
    • A2.4 LM Functions
    • A2.5 LM Parameters
      • A2.5.1 LM Parameter List
      • A2.5.2 Descriptions for LM Parameters
    • A2.6 FAQs
  • Appendix 3. DD Methods and DD Menu
    • A3.1 Overview
    • A3.2 DD Methods
      • A3.2.1 Transducer Block
      • A3.2.2 AO Block
      • A3.2.3 OS Block
  • Appendix 4. Software Download
    • A4.1 Benefits of Software Download
    • A4.2 Specifications
    • A4.3 Preparations for Software Downloading
    • A4.4 Software Download Sequence
    • A4.5 Download Files
    • A4.6 Steps after Activating a Field Device
    • A4.7 Troubleshooting
    • A4.8 Resource Block’s Parameters Relating to Software Download
    • A4.9 System/Network Management VFD Parameters Relating to Software Download
    • A4.10 Comments on System/Network Management VFD Parameters Relating to Software Download
  • Appendix 5. Position Adjustment of Feedback Lever
  • Appendix 6. Manual Tuning Guideline
    • A6.1 General
    • A6.2 Control Parameter Tuning Procedure
    • A6.3 Examples of Tuning Control Parameters
    • A6.4 Description of Control Parameters
  • Installation and Operating Precautions for TIIS Flameproof Equipment
  • Customer Maintenance Parts List
    • YVP110
    • Advanced Valve Positioner
  • Revision Record