How to use the remote control, Quietmaster programmable) – Friedrich KS15 User Manual
Page 5
5
920-198-00
* A Friedrich RC1 wireless remote control can be used to operate all
QuietMaster
®
Programmable models.
Figure 4
To start unit
1 POWER - Press the Power button once. The unit will automatically
turn on in the mode and fan speed it was last left on.
To set mode of operation
2 COOL - Press the Cool button to automatically switch the operating
mode to COOL.
3 FAN ONLY - Press the Fan Only button if you want to run the fan only.
You may want to use this feature in conjunction with the Fresh Air/
Exhaust if you want to bring outside air into the room, or exhaust stale
air. (The FRESH AIR / EXHAUST feature is located on the front of the
air conditioner near the top. See Figure 9 on page 7.)
4 MoneySaver
®
- Press the MoneySaver
®
button to activate the
MoneySaver
®
feature. This cycles the fan with the compressor so
that the fan does not run all the time.
To adjust temperature
5 COOLER - Press the Cooler button to raise the temperature
setting.
6 WARMER - Press the Warmer button to lower the temperature
setting.
To adjust fan speed
7 FAN SPEED - Press the Fan Speed button to see the current set-
ting. Press again to change the fan speed. F1 is the lowest setting
(SLEEP SETTING), F2 is low speed (LOW), F3 is medium (MED),
and F4 is high (HIGH).
To set the hour clock
8 SET HOUR CLOCK - Press Set Hour once to see the current clock set-
ting. Continue pressing the button until you arrive at the current time.
MAKE SURE YOU SET THE A.M. AND P.M. PROPERLY. (NOTE:
MINUTES ARE NOT SHOWN ON THE DISPLAY.) A light will appear in
the upper left corner of the display when the hour is P.M.
How to use the remote control
*
(QuietMaster Programmable)
To set the timer
NOTE: Set the hour clock before attempting to set timer functions. You
can set the timer On/Off a minimum of one hour apart, and a maximum
of 23 hours apart.
9 TIMER START - Press Start to view the current start time for cool-
ing. Continue pressing the Start button until you arrive at the start
time you desire. The start time for cooling will then be set.
10 TIMER STOP - Press the Stop button. Continue pressing the Stop
button until you arrive at the stop time you desire. The stop time for
cooling will then be set.
11 TIMER ON/OFF - Press the On/off button once to activate (light on)
or deactivate (light off) the timer. Once the Start and Stop times
have been selected, they will remain in memory, and cycle daily until
changed.
NOTE: If the unit is unplugged or the power is interrupted, the HOUR
CLOCK must be reset or the Timer On/off functions will not work.
Money
Fan
Timer Operation
Set Hr.
Stop
Start
Temperature
Fan
Cool
On/Off
Power
Cooler
Only
Speed
Saver
®
Warmer
8
10
7
11
9
4
3
1
2
5
6
- EM24 ES16 EM18 EL36 WallMaster Series 12000 BTU Thru-the-Wall Smart Air Conditioner Warranty WallMaster Series 11600 BTU Thru-the-Wall Smart Air Conditioner Warranty WallMaster Series 8000 BTU Smart Thru-The-Wall Air Conditioner Warranty Chill Premier Series Slide-Out Chassis Smart Room Air Conditioner Warranty Kuhl Series 28000 BTU Window Air Conditioner Warranty Chill Premier Series Slide Out Chassis Smart Window Air Conditioner Warranty Chill Premier Series Smart Window Air Conditioner Warranty ZoneAire Series 11,000 BTU Smart Portable Air Conditioner Warranty ZoneAire Series Single Hose Smart Portable Air Conditioner Warranty ZoneAire Series 12,000 BTU Dual Hose Smart Portable Air Conditioner Warranty CP06 ZQ07 ZQ05 CP12 P012A P012B ZStar D30C D40C D65C CP08 ZQ10 ZQ08 CP18C30 Kuhl Series 23,000 BTU Smart Window Wall Room Air Conditioner Warranty Kuhl Series 12000 BTU Smart Window Air Conditioner Warranty