Kenwood VR-507 - Manual (Page 22)

22
Operations
Muting the sound
The MUTE key lets you mute the sound of the speakers.
Press the MUTE key.
To cancel
Press the MUTE key again so that the “MUTE” indicator goes off.
• MUTE ON can also be deactivated by turning the volume control
knob.
Blinks
1 Use the INPUT SELECTOR knob to select the source (other
than “MD/TAPE”) you want to record.
2 Set the cassette deck or MD recorder to record.
3 Start playback, then start recording.
Recording audio (analog sources)
Recording
Recording a music source
1 Press the MONITOR key.
2 Use the INPUT SELECTOR knob to select a source other than
“MD/TAPE”.
3 Start playback on the cassette deck connected to the
MONITOR jacks and start recording on the cassette deck or
MD recorder connected to the MD/TAPE jacks.
Recording tapes or MD (with MONITOR function)
1 Use the INPUT SELECTOR knob to select “MD/TAPE.”
2 Start playback on the cassette deck connected to the MD/TAPE
jacks and start recording on the cassette deck or MD recorder
connected to the MONITOR jacks.
MONITOR = MD/TAPE recording
MD/TAPE = MONITOR recording
• To copy tapes using a double cassette deck, refer to the
instruction manual of the double cassette deck.
MONITOR function (analog sources only)
You can connect a cassette deck or graphic equalizer to the MONITOR
jacks of the receiver. If a graphic equalizer is connected, the MONITOR
key should be left in the on position. Alternately, if a cassette deck
equipped with a 3-head system is connected to the
MONITOR jacks,
you will be able to monitor the just-recorded signal while making
recordings on the cassette deck. By switching the
MONITOR key on
and off, you can compare the sound of the source signal and the just-
recorded signal. For more information, refer to the instruction manual of
the connected component.
Normal playback
S.DIRECT
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
DSP
MEMO
ST.
TUNED
AUTO SOUND AUTO
STEREO MONITOR
Listening with headphones
1 Press the SPEAKERS A or B key so that the speaker indica-
tor goes off.
Make sure the SPEAKERS
indicators are turned off.
2 Connect headphones to the PHONES jack.
• If you turn off all of the speakers when in surround mode, the
surround mode will be canceled as well, resulting in stereo playback.
R L
LFE
C
S RS LS
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
SP A
PHONES
SOURCE DIRECT playback (for analog input sources only)
Use this function to pass the source material direct to the amplifier,
bypassing any audio processing.
To cancel
Press the SOURCE DIRECT key.
• When you press the LISTEN MODE, SOUND, or SET UP keys,
or switch to another input source, SOURCE DIRECT playback will
be canceled.
• If CINEMA EQ. is switched ON, SOURCE DIRECT key will not be
effective.
• If SOURCE DIRECT is switched ON, CINEMA EQ. function will not
be effective.
Press the SOURCE DIRECT key again.
• If SOURCE DIRECT playback was activated while in surround mode,
canceling SOURCE DIRECT playback will reactivate the previous
surround mode.
STEREO
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND AUTO
S.DIRECT
LFE
C
S RS LS
TI.VOL B
CLIP
RDS EON PTY
TP TA NEWS
SW
L SP A R
MUTE
INPUT SELECTOR
MONITOR
3 Use the VOLUME CONTROL knob or VOLUME keys to adjust
the volume.
*5027/20-22/EN 3/15/01, 3:10 PM 22