Kenwood VR-507 - Manual (Page 27)

27
Operations
Surround play
The DTS compatible models can reproduce a CD, DVD, or LD carrying
the DTS mark.
DOLBY DIGITAL can be used when playing DVD or LD software bearing
the mark and DOLBY DIGITAL format digital broadcasts (etc.).
DOLBY PRO LOGIC and DOLBY 3 STEREO can be used when playing
video, DVD, or LD software bearing the
mark.
• Turn ON related components.
• Complete “Preparing for surround sound” (speaker settings).
(
• Use the INPUT SELECTOR to select the component you wish to play
back with surround sound.
• Use the INPUT MODE key to select the input mode (analog or digital)
for the source you wish to play back. 9
• Noise will be produced when a DTS source is played by selecting the
analog input.
Preparations
RC-R0720
RC-R0613
INPUT
SELECTOR
INPUT SELECTOR INPUT MODE
LISTEN MODE
LSTN M.
1
Start playing the video software.
2
Press the LISTEN MODE or LSTN M. key to select the
listening mode.
The listening mode settings are stored separately for each input. If the
input mode is set to digital auto (
“AUTO SOUND” lights), the receiver
selects the optimal listening mode automatically based on the type of
input signal and the speaker settings.
Each press of the LISTEN MODE or LSTN M. key switches the
setting as listed below.
The listening mode settings are different depending on the type
of input signal.
When the DTS signal is input:
(The DTS indicator lights up.)
1 DTS: DTS surround
2 STEREO: Normal stereo playback
When the analog signal or the digital signal (except for
DOLBY DIGITAL or DTS signal) is input:
1 PL II MOVIE: PRO LOGIC II surround MOVIE mode
(The PRO LOGIC indicator lights up.)
2 PL II MUSIC: PRO LOGIC II surround MUSIC mode
(The PRO LOGIC indicator lights up.)
3 PRO LOGIC: PRO LOGIC II surround PRO LOGIC mode
(The PRO LOGIC indicator lights up.)
4 3 STEREO: 3-STEREO mode
(The 3 STEREO indicator lights up.)
5 CIRCLE SURROUND: CS 5.1 surround
(The CS 5.1 indicator lights up.)
6 ARENA: DSP Surround ARENA mode.
7 JAZZ CLUB: DSP Surround JAZZ CLUB mode.
8 THEATER: DSP Surround THEATER mode.
9 STADIUM: DSP Surround STADIUM mode.
0 DISCO: DSP Surround DISCO mode.
- STEREO: Normal stereo playback. Sound is produced
from the two front channels only.
• If Dolby Digital or DTS signal having more channels than the
maximum number of playback channels available using the
receiver’s current settings is input, the
DOWNMIX indicator on
the front panel lights up and downmixing is performed to match
the number of available channels.
Notes
• Depending on the type of the signal or speaker setting, some listening
modes cannot be selected.
• When playback is started, the sound may be cut or interrupted before
the input source is confirmed as Dolby Digital.
• To enjoy Dolby Digital surround (as well as all the other listening
modes) from a single component, be sure to use a Dolby Digital
compatible source component. Connect the Dolby Digital compatible
source component's Dolby Digital format digital audio signal to one of
the DIGITAL INPUT jacks on the back of the receiver. Connect the
normal audio signal correctly to the respective component's AUDIO
jacks.
0!@#
Adjust the volume.
3
When the DOLBY DIGITAL signal is input:
(The DOLBY DIGITAL, PROLOGIC, or 3 STEREO indicator lights up.)
1 DOLBY DIGITAL: DOLBY DIGITAL surround
2 PL II MOVIE: PRO LOGIC II surround MOVIE mode
(The PRO LOGIC indicator lights up.)
3 PL II MUSIC: PRO LOGIC II surround MUSIC mode
(The PRO LOGIC indicator lights up.)
4 PRO LOGIC: PRO LOGIC II surround PRO LOGIC mode
(The PRO LOGIC indicator lights up.)
5 3 STEREO: 3-STEREO mode
(The 3 STEREO indicator lights up)
6 STEREO: Normal stereo playback
When you select DOLBY DIGITAL
STEREO
FM
AM
MHz
kHz
3
DOWN MIX
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
SP A R C L
SR SR SL SL
AUTO SOUND DIGITAL
SW LFE
PRO LOGIC
S
Ambience effects
“DOLBY DIGITAL” will be scrolled from right to left.
*5027/26-34/EN 3/15/01, 3:11 PM 27