Kenwood VR-507 - Manual (Page 6)

6
Preparations
TI.VOL
TP
RDS EON PTY
TA NEWS
FM
AM
MHz
kHz
PRO LOGIC
3 STEREO
DOWNMIX
DIGITAL
S.DIRECT
MONITOR MEMO
ST.
TUNED
AUTO SOUND AUTO SP
LFE SW
C A B
MUTE
S SR SL
R L
A SPEAKERS B
STANDBY
POWER
MULTI CONTROL
LISTEN MODE SOUND SOURCE DIRECT
AUTO/CINEMA EQ. BAND MEMORY
INPUT SELECTOR
VOLUME CONTROL
UP DOWN
PRO LOGIC 3 STEREO CS 5.1
DOLBY
DIGITAL
DTS
INPUT MODE SET UP
S-VIDEO V L – AUDIO – R AV AUX
DIMMER MONITOR
PHONES
ON/STANDBY
ON OFF
STANDBY
POWER
ON/STANDBY
DSP
CLIP
Display
Speaker selection indicators
Input channel indicators
Output channel indicators
Band indicators
AUTO indicator
MEMO indicator
ST. indicator
TUNED indicator
3 STEREO indicator
STEREO indicator
Names and functions of parts
Frequency display,
Input display,
Preset channel display,
Surround mode display
Speaker indicator
PRO LOGIC
indicator
S.DIRECT indicator
MONITOR indicator DOWNMIX indicator
MUTE indicator
AUTO SOUND indicator DIGITAL indicator
1 POWER key (For KRF-V7050D) (
Use to turn the main power ON/OFF.
2 ON/STANDBY ( ) key (
(For KRF-V7050D)
Use to switch the power ON/STANDBY when
the POWER is turned ON.
STANDBY indicator
2 POWER ( ) key (For VR-507) (
Use to turn the power ON/STANDBY.
STANDBY indicator
3 MULTI CONTROL knob (
Use to control a variety of settings.
4 SET UP key (
Use to select the speakers' settings etc.
5 Surround indicators
DTS indicator ¶
Lights when the receiver is in the DTS mode.
DOLBY DIGITAL indicator
¶
Lights when the receiver is in the Dolby Digital
mode.
PRO LOGIC indicator
¶
Lights when the receiver is in the PRO LOGIC
mode.
3 STEREO indicator ¶
Lights when the receiver is in the 3 STEREO
mode.
CS 5.1 indicator
¶
Lights when the receiver is in the CS 5.1 mode.
6 INPUT MODE key 9
Use to switch between the digital and analog
inputs.
7 DIMMER key £º
Use to adjust the brightness of the display.
Use to select the REC MODE.
8 MONITOR key ™
Use to monitor the source that is connected to
the MONITOR jack.
9 VOLUME CONTROL knob ¡
0 PHONES jack ™
Use for headphone listening.
! SPEAKERS A/B keys )
Use to turn the A/B speakers ON/OFF.
@ SOUND key •
Use to adjust the sound quality and the ambi-
ence effects.
DSP indicator
# BAND key £
Use to select the broadcast band.
$ AUTO/CINEMA EQ. key
Use to change “TAPE” indication to “MD”.
)
Use to select the auto tuning mode. £
Use to switch the status of CINEMA EQ. ™
% LISTEN MODE key ¶
Use to select the listening mode.
^ MEMORY key ™
Use to store radio stations in the preset memory.
& SOURCE DIRECT key ¢
Use to pass the source material directly to the
amplifier.
* INPUT SELECTOR knob ¡
Use to select the input sources.
( AV AUX (S VIDEO, V, AUDIO L/R) jacks
$
Standby mode
When standby indicator is lit, this receiver is in standby mode and consumes a small amount of curent for back-up. This system can be switched on using
remote controls.
CLIP indicator
For VR-507
*5027/01-09/EN 3/15/01, 2:53 PM 6