Panasonic WV-CP474 - Manual (Page 2)

1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light Control (ELC)
(2) The SUPER-D2 function eliminates interference by strong background lighting
which makes the camera picture dark, such as a spotlight.
Dynamic range of 46 dB.
(3) Various External Sync Functions, including Gen-Lock
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)
3. Minimum Illumination of 0.8 lx (0.08 foot-candle) at color mode, 0.1 lx (0.01 foot-candle)
at black and white mode with F1.4 lens.
4. 480 lines of horizontal resolution
5. High quality picture:
(a) 2H type vertical enhancer for greater picture sharpness
(b) Chroma averaging circuit for better color signal-to-noise ratio
(c) Minimum of aliasing on fine objects
(d) Expanded dynamic range by use of knee circuit
(e) Highlight aperture correction for greater picture detail of bright objects
6. Ability to shoot indoor scenes with fixed iris lens by use of Electronic Light Control (ELC)
function.
7. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF
8. Built-in Digital Motion Detector
9. Auto black-and-white mode enables the camera to switch between color and black-
and-white picture in response to light input.
FEATURES
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q Auto Iris Lens Connector
Connects the auto iris lens with a 4-pin male connector supplied as a standard acces-
sory (Part No. YFE4191J100).
w Flange-back Adjusting Ring
Adjusts the back focal length and picture focus.
e Flange-back Fixing Screw
r Lens (Option)
t Camera Mounting Screw Hole
Mounts the camera onto a mounting bracket.
y Down Button (
K
)
Moves the cursor downward and selects items in the CAM SET UP menu.
u Left Button (
L
)
Moves the cursor to the left, selects the mode and adjusts some levels.
i Up Button (
J
)
Moves the cursor upward and selects items in the CAM SET UP menu.
o Right Button (
M
)
Moves the cursor to the right, selects the mode and adjusts some levels.
!0 Set Button (
I
)
Activates an item selected in the CAM SET UP menu.
!1 Gen-lock Termination Switch (Hi-Z, G/L 75
Ω
)
Set this switch to Hi-Z when a gen-lock video input signal is looped through. In all other
cases, set this switch to 75
Ω
.
!2 Gen-lock Input Connector (GEN-LOCK)
Connects an external system for synchronization.
!3 Video Output Connector (VIDEO OUT)
Connects the VIDEO IN connector of the monitor.
!4 Power Indicator (POWER)
!5 Alarm Output Terminal (ALARM OUT/GND)
Connects to the alarm input connector (terminal) of an external device. When the cam-
era detects motion, the alarm output signal is supplied to the connected external device
(Open collector output: 16 V DC, 100 mA max).
GEN-LOCK
AC 120V 60Hz
VIDEO OUT
POWER
ALARM
DAY/
NIGHT
GND
OUT
GND
IN
y
o
u !0
!1 i
Hi-Z G/L 75 Ω
q e
!7
!3 !2
!3 !2
w r
t
GEN-LOCK
GND
1
2
VIDEO OUT
POWER
ALARM
AC 24V IN
DC 12V IN
DAY/
NIGHT
GND
OUT
GND
IN
!4
!4
!8
!5
!6
!5
!6
WV –
CP470
WV-CP470
WV-CP474
Slide the panel to the left until it locks.