Panasonic SC-HT900 - Manual (Page 27)

27
RQT6750
Ra
dio ope
ra
ti
o
n
s
The radio
1
Press [SELECTOR] to select “FM” or “AM”.
Each time you press the button:
DVD/CD
>FM>AM>TV>VCR>AUX>DIGITAL IN ([HT900])
^----------------------------------------------------------------------------}
≥Remote control: Press [TUNER/BAND].
2
Press [TUNE MODE] to select
“MANUAL”.
Each time you press the button: MANUAL ()PRESET
3
Press [ X TUNING] or [TUNING W] to
select the frequency of the required
station.
≥Remote control: Press [6] or [5].
TUNED: Displayed when a radio station is
tuned.
ST: Displayed when a stereo FM broadcast is
being received.
Press and hold [ XTUNING] or [TUNINGW] until the frequency
starts scrolling to start automatic tuning. Tuning stops when a
station is found.
4
Adjust the volume.
∫ If noise is excessive in FM
Press [FM MODE] to display “MONO”.
Press [FM MODE] again to cancel the mode.
The mode is also canceled when you changed
the frequency.
∫ Allocation settings
Each country allocates broadcast bands according to their particular
system.
[For\U.S.A.,\Canada,\and\units\with\PX\printed\on\the\outer\packaging]
You can change the FM step. The step is factory-set to 0.2 MHz, but
you can change it to receive broadcasts allocated 0.1-MHz steps.
[For\Latin\America]
You can change the AM step. The step is factory-set to 9 kHz, but
you can change it to receive broadcasts allocated 10-kHz steps.
1 Press [TUNER/BAND] to select “FM” (for either band).
2 Press and hold [SELECTOR] on the main unit.
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM/AM frequencies preset in channels will be changed by this
procedure. Preset them again.
Preset channels to make selection simple.
Up to 15 stations can each be set in the FM and AM bands.
1
Tune to “FM 87.9 MHz” or
“FM 87.5 MHz” (
➡ left).
[For\Latin\America]
Tune to “FM 87.50 MHz” (
➡ left).
2
Press and hold [ENTER].
≥Main unit: Press and hold [MEMORY].
Release the button when “FM AUTO” is displayed.
The tuner presets all the stations it can receive into the
channels in ascending order.
“SET OK” is displayed when the stations are set. The last
station to be set is then played.
3
Tune to “AM 520 kHz”.
[For\Latin\America]
Tune to “AM 522 kHz” or “AM 520 kHz”.
4
Press and hold [ENTER].
≥Main unit: Press and hold [MEMORY].
∫ “ERROR” is displayed
Presetting was unsuccessful. Preset manually.
1
Tune to the station (
➡ left).
2
Press [ENTER].
3
While “PGM” is flashing
Press the numbered buttons to select
a channel.
Alternatively, press [ :, X CH] or [9, CH W] then press
[ENTER].
The station occupying a channel is erased if another station is preset
in that channel.
1
Press [TUNER/BAND] to select “FM”
or “AM”.
2
Press the numbered buttons or
[
:, X CH] or [9, CH W] to select
the channel.
To select a 2-digit number
Example: To select channel 12, press [
S10] ➡ [1] ➡ [2]
Manual tuning
PROGRESSIVE DISC EXCHANGE SELECTOR DISC SKIP
DOWN
VOLUME
UP
OPEN/CLOSE
C.S.M
DISC V.R.S M.R.S 1 2 3 4 5
TUNE MODE TUNING FM MODE MEMORY
AV SYSTEM
TV/VIDEO
DISC
PAGE
GROUP
SEQUENTIAL
REPEAT
PLAY MODE
FL DISPLAY
CANCEL
SKIP
CH
TOP MENU
DISPLAY
VOLUME
SUBWOOFER
LEVEL
S.POSITION
SFC
C.FOCUS
S SRND
MIX 2CH
PL
RETURN
TV VOL s TV VOL r
DIRECT
NAVIGATOR
PLAY LIST
MENU
SLOW/SEARCH
1 2 3
4 5 6
7 8
0
9
TUNER/BAND DVD/CD
TV VCR
ENTER
DIGITAL
AUX
S10/ENTER
DISC 1 DISC 2
DISC 4 DISC 5
DISC 3
TUNER/BAND
: 9
X
CH
W
VOLUME
j i
MEMORY TUNE MODE
X
TUNING
W
VOLUME, DOWN, UP SELECTOR
FM MODE
ENTER
6 5
Numbered
buttons
TUNEDST
MONO
Preset tuning
Automatic presetting
Manual presetting
Selecting channels