Messages displayed on the touch panel – Toshiba e-studio 5520C User Manual
Page 10
1 TROUBLESHOOTING FOR THE HARDWARE
8 Messages Displayed on the Touch Panel
Messages Displayed on the Touch Panel
When a message appears on the touch panel, see the table below to solve the problem.
Message
Problem Description
Solution
Close *** cover.
The cover indicated by *** is open.
Check the cover on the touch panel and close it.
Misfeed in ***
Paper jam has occurred inside the
equipment.
Remove the jammed paper following the guidance
displayed on the touch panel.
Install new *** toner cartridge
No toner is left. “***” indicates the
color.
(The colors are shown abbreviated
when two or more toners are running
out: Y: yellow, M: magenta, C: cyan,
and K: black.)
See the color indication on the touch panel and
replace the toner cartridge.
(About another 2000 copies can be made after this
message appears. The number varies depending on
the conditions of copying.)
P.46 “Replacing a Toner Cartridge”
Check paper size setting on control
panel for drawer N
Paper jam has occurred because of
the mismatch between the paper size
placed in drawer N and the size
registered for drawer N on the
equipment.
Just removing the jammed paper does not prevent
another paper jam. Be sure to correctly register the
paper size in the equipment.
P.33 “Clearing paper jams caused by a wrong
Check paper type setting for drawer N Paper jam has occurred because of
the mismatch between the paper type
placed in a drawer N and the type
registered for the drawer N on the
equipment.
Just removing the jammed paper does not prevent
another paper jam. Be sure to correctly register the
paper type in the equipment.
P.38 “Clearing paper jams caused by a wrong
Paper for left drawer can be added
No paper is left in the left tray of the
Tandem Large Capacity Feeder.
You can add paper while the copy function is in
operation. Open the drawer of the Tandem Large
Capacity Feeder and add paper in the left drawer.
For details, refer to Chapter 1 of the Copying Guide.
TRU Box needs to be replaced
(Please make a service call)
The TRU box requires replacement
by a service technician.
Contact your service representative.
Prepare new waste toner box
The waste toner box is nearly full.
Have a new waste toner box ready for the
replacement.
Wait (Performing Self-check)
The equipment is undergoing the
maintenance to keep its imaging
quality.
Wait until the maintenance is completed and the
message disappears.
Check the original and set it again
The original is jammed inside of the
Reversing Automatic Document
Feeder.
Remove the jammed original following the guidance
on the touch panel.
P.13 “Paper jam in the Reversing Automatic
The direction or the size of the
original placed on the Reversing
Automatic Document Feeder is
incorrect.
Check the direction and the size of the original and
then replace it on the Reversing Automatic Document
Feeder. Then reattempt the operation.
Change direction of original
The orientation of the original placed
on the original glass is incorrect.
Change the orientation of the original by 90 degrees
and place it on the original glass.
Time for Developer (*) Maintenance.
(The colors are shown abbreviated:
Y: yellow, M: magenta, C: cyan and K:
black.)
Little developer remains. “*” indicates
the color of the developer.
Contact your service representative.
Cannot print this paper size
Select the other Drawer
A printing was attempted but failed.
The paper could not be output on the
tray selected for the paper output
because of the mismatch between the
paper size and the tray.
1. The paper with the size of 320
mm x 450 mm, 320 mm x 460 mm
or 330 mm x 483 mm (13" x 19")
was attempted to be output in the
lower receiving tray of MJ-1103/
MJ-1104.
2. The paper with the length of 457
mm (18") or longer was attempted
to be output in the lower receiving
tray of MJ-1103/MJ-1104.
3. The paper with the length of 483
mm (19") or longer was attempted
to be output in the receiving tray
of the Finisher.
Delete the failed print job, select the appropriate tray
for the paper, and perform printing again.