Samsung PL50A450P1XZP - Manual (Page 55)

English - 55
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
2 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the ENTER button.
 Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
4 Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
5 Press the EXIT button to exit.
➢ If your receiver supports audio only, it may not appear in the device list.
➢ When listening through the receiver, there are restrictions for using the audio-related (MTS, Preferred language)
menus.
➢ If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power
failure), the TV Speaker may be set to Off when you turn the TV on again.
Check Points before Requesting Service
Symptom Solution
Anynet+ does not work. ■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices
only.
■ Connect only one receiver (home theater).
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work in certain situations. (Searching channels, Plug & Play, etc.)
■ When connecting or removing the HDMI cable, please make sure to search devices
again or turn your TV off and on again.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+. ■ Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
(HDMI-CEC) is set to On in the Anynet+ Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then press the TOOLS
button to show the Anynet+ menu and select a menu you want.
I want to exit Anynet+. ■ Select View TV in the Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a device other than
Anynet+ devices.
■ Press CH, CH LIST, PRE-CH to change to the TV mode.
(Note that the channel button operates only when an Anynet+ device with a built-in tuner
is not connected.)
The Connecting to Anynet+ device...
message appears on the screen.
■ You cannot use the remote control when you are configuring Anynet+ or switching to a
view mode.
■ Use the remote control when the Anynet+ setting or switching to view mode is complete.
The Anynet+ device does not play. You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may
not support Anynet+ functions.
The TV program cannot be
recorded.
Check whether the antenna jack on the recording device is properly connected.
Enter Move
TV Air 11
Return
View TV
Select Device ►
Record ►
Menu on Device ►
Device Operation ►
Receiver :On ►
Setup ►
BN68-01449A.indb 55 2008-04-07 오후 6:03:23