Karcher B 60-10 C HYGIENE - Manual (Page 7)

- 2
Figure 2, see cover page

Install the carrying handle to the hous-
ing.
The following attachments can be installed
optionally:
Figure 3, see cover page

Put the hook for the accessories in the
depression on the appliance.
 Place the mop (not included in the
scope of delivery) onto the mop holder.
 Attach the hook to the mop stick and
slide it down into the depression of the
appliance.
 Secure the hook to the mop stick using
the accompanying screw.
ATTENTION
Risk of damage. Only use the recommend-
ed detergents. With other detergents, the
operator bears the increased risk regarding
the operational safety, risk of accident and
reduced service life of the appliance. Only
use detergents that are free of solvents, hy-
drochloric acid and hydrofluoric acid.
Follow the safety instructions for using de-
tergents.

Open the cover of the fresh water reser-
voir.
 Pour in water/detergent mixture. Maxi-
mum temperature of the liquid 50 °C.
 Close the cover of the fresh water res-
ervoir.
Figure 4, see cover page

Swivel up cleaning head.
 Cut off a piece of fleece with a length of
4 sections.
 Place the half width of the fleece onto
the pad and press down.
Figure 5, see cover page

Turn up the fleece onto the top of the
cleaning head and stretch it onto the
tips of the holders.
 Sweep loose dirt off the surface to be
cleaned.
 Swivel down the cleaning head.
 Turn the dosing of the cleaning solution
to the desired value.
The cleaning solution starts to flow
when the rotary knob leaves the "OFF"
position.
Note:
If the cleaning head is swivelled up, no
cleaning solution is applied.

Push the appliance forward at a normal
walking speed.
 Turn the dosing of the detergent to the
"OFF" position.
 Continue to push the appliance for ap-
prox. 30 seconds in order to absorb the
cleaning solution.
 Swivel up cleaning head.
 Mop up remaining cleaning solution.
 Remove the lid of the waste water con-
tainer.
ṇ WARNING
Please observe the local provisions regard-
ing the wastewater treatment.

Empty the wastewater container and
clean it under running water.
 Clean the lid of the waste water contain-
er under running water.
Figure 6, see cover page
ṇ WARNING
Please observe the local provisions regard-
ing the wastewater treatment.

Pull the upper end of the filling level in-
dicator for fresh water out of the appli-
ance.
 Swivel down the filling level indicator
over a disposal unit and drain the clean-
ing solution.
 Put the filling level indicator back into
the opening on the appliance.
Figure 7, see cover page
To reduce the space requirements for stor-
age or transport in vehicles, the push han-
dle can be folded in.

Loosen the lock nuts.
 Swivel the push handle by 180° towards
the front.
 Tighten lock nuts.
ṇ CAUTION
Risk of personal injury or damage! Mind the
weight of the appliance during transport.

Swivel up cleaning head.
 Use the pushing handle to push the ap-
pliance.
 When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
ṇ CAUTION
Risk of personal injury or damage! Consid-
er the weight of the appliance when storing
it.
This appliance must only be stored in inte-
rior rooms.
 Empty the dirt water reservoir.
 Empty the fresh water reservoir.
 Rinse the appliance: Fill the fresh water
tank with clear water (without deter-
gent), open the dosing unit for the
cleaning solution and allow the tank to
drain.
 Clean the outside of the appliance with
a damp cloth which has been soaked in
mild detergent.
 Turn around or dispose of the fleece.
 Clean the suction stub.
 Remove, clean and reattach the pad.
 Clean the squeegee, check for wear
and replace if necessary (see "Mainte-
nance work").
 Check appliance for damage.
 Check the pad for wear and replace if
necessary (see "Maintenance work").
 Check appliance for leaks.
 Clean drive wheel.
 Swivel up cleaning head.
Figure 8, see cover page

Pull out the spring plug.
 Remove holding strip.
 Remove squeegee.
 Attach new or turned squeegee.
Figure 9, see cover page

Hook the holding strip onto the cleaning
head.
 Push the holding strip onto the cleaning
head and insert the spring cotter pin.
 Swivel up cleaning head.
 Remove fleece.
 Remove the pad.
Figure 10, see cover page

Fit new pad and press it onto the Velcro
tape on the cleaning head.
 Loosen the lock nuts.
 Pull back the cleaning head.
 Swivel up the holder.
In case of danger of frost:

Empty the fresh and dirt water reser-
voirs.
 Store the appliance in a frost-protected
room.
Initial Start-Up
Operation
Fill fresh water reservoir
Attaching fleece
Cleaning
Complete cleaning
Emptying the Fresh Water Reservoir
Folding in the push handle
Transport
Storage
Maintenance and care
Maintenance schedule
After the work
Weekly
Maintenance Works
Turning around/replacing the squeegee
Replacing the pad
Dismantling the cleaning head
Frost protection
7 EN