Philips 58PFL4609-F7 - Manual (Page 29)

Sound
Before you begin:
You must set Home in Location. L p. 35
Otherwise, personalized Picture and Sound settings will not be
memorized after the Unit goes into Standby Mode.
1
Press Q (MENU) and use H I J K to select Setup then press
OK.
2
Use H I to select Sound, then press OK.
Software
Installation
Features
Sound
Picture
Settings assistant
PCM
On
Off
Start now
Personal
Digital output format
Headphone volume
TV speakers
Auto volume leveling
Balance
Equalizer
Auto sound
Off DTS TruSurround
3
Use H I J K to select the item you want to adjust, then press
OK.
The following sound settings can be configured. Depending on the format
of the broadcasting, some sound settings are not available.
Auto sound
to select the desired Setting, then press OK.
(Personal, Standard, Vivid, Sports, Movie, Music
and News)
When you adjust the following settings
(Equalizer, DTS TruSurround and Auto volume
leveling), Personal sound will be set
automatically.
Adjust the tonal quality for each frequency.
Equalizer
J Cursor Cursor K
to select the specific frequency using H I, and
use J K to Adjust the Level, then press OK.
Adjust the speakers to suit your listening preference.
Balance
J Cursor Cursor K
Adjusts the balance of the right and left speakers
to Best suit your listening position.
Digital TV Operation
You can select the Audio language while your TV is receiving the Digital
broadcasting.
Digital audio
language
to select the language according to your
preference.
(It differs depending on the program.)
Cable / NTSC (Analog) TV Operation
You can select Main or SAP while your TV is receiving the Analog
broadcasting that has the SAP (Second Audio Program).
(It differs depending on the program.)
Alternate audio
Main to output main-audio
SAP to output second-audio program
Cable / NTSC (Analog) TV Operation
When you set to Main in Alternate audio above, you can select Mono
or Stereo if the Analog broadcasting is sending the MTS (Multichannel
television sound).
Mono/Stereo
Mono to Output mono-audio.
Stereo to Output stereo-audio.
This selects sound modes for more spatial or surround sound
reproduction.
DTS TruSurround
Off to set DTS TruSurround™ to Off
On to set DTS TruSurround™ to On
This function keeps a constant loudness differential between the TV
commercials and the programs.
Auto volume
leveling
Off
to Remove the Auto volume
leveling
On
to Reduce Volume Differences
between the TV Commercials and
the Programs
You can select the Audio Output from the unit’s speakers or not. If your
amplifier is HDMI link function compatible and connected by an HDMI
cable to this unit, some sound operations such as volume up can be
changed by using this unit’s remote control. Make sure Master EasyLink
is set to On. L p. 36
TV speakers
Off
not to Output Sound from the
Unit’s Speakers
On
to Output Sound from the Unit’s
Speakers
Speakers
EasyLink
to control Audio Output from
your connected EasyLink
Compliant Devices with VOL + /
- by using this Unit's remote
control.
Adjust headphone volume.
Headphone
volume
J Cursor Cursor K
to decrease or increase volume
You can set the digital audio output format from SPDIF/ARC.
Digital output
format
PCM to Output PCM format.
Bitstream
to Output Audio in its native
format as Bitstream to connected
Audio receiver.
If a channel or Input device is too loud or too soft, navigate to that channel
or Input device.
Delta volume
J Cursor Cursor K
to set a negative delta
volume level as per
your personal
preferences to set a positive delta
volume level as per
your personal
preferences
Note(s)
● Alternate audio and Mono/Stereo are not available when you watching TV programs with
a cable box or satellite set-top box connected through an HDMI cable or Component /
Composite Video cables.
29 .
English