Philips 40PFL5706-F7 - Manual (Page 23)

22
Setting items Description
Color
enhancement
Off Sets Color enhancement to off.
On Makes colors more vivid bright colors.
Active control
Off Sets Active control to off.
On with
Light
Sensor
Adjusts backlight for the best picture quality by
dynamically adjusting the backlight intensity in
accordance with lighting condition in the room.
On without
Light
Sensor
Adjusts backlight for best picture quality based
on the incoming video signal.
Picture format
Automatic
Refer to ‘Summary of picture formats’ on
page 23.
Super zoom
4:3
Movie
expand 14:9
Movie
expand 16:9
Wide
screen
Unscaled
Mode selection
PC
Turns off image enhancement features which
makes the TV to act purely as a monitor.
HDTV
Enables image enhancement features to
improve picture quality.
Auto adjustment
The horizontal / vertical position, clock and
phase of the PC screen are automatically
adjusted.
Clock Setting to stabilize the PC screen.
Phase Setting to improve the clarity of the PC screen.
Horizontal shift
Adjusts the horizontal position of the picture
for PC screen.
Vertical shift
Adjusts the vertical position of the picture for
PC screen.
5
Press MENU to exit.
Note
• [ Mode selection] will not be displayed when incoming signals are other than
720 x 480p 60Hz, 1280 x 720p 60Hz and 1920 x 1080p 24 / 30 / 60Hz.
• [Digital Natural Motion] If the input video contains adjacent video frames with
inherent motion blur captured by the video camera, [Digital Natural Motion] will
interpolate blur and cause streaking artifacts in high motion scenes. If the content
you are watching causes a lot of Interpolation Induced Blur Amplifi cation, it is best
to turn off [Digital Natural Motion] temporarily.
• [Digital Natural Motion] uses frame interpolation to make the video appear
smooth which causes a video lag of about 200 milliseconds. If you are using the TV
for gaming or as a PC monitor DNM will introduce lag. If your gaming system has a
lag adjustment feature for your game controller, use it to negate the lag or else turn
off DNM for any application where lag is an issue. If your prefer to use DNM while
watching movies on your Home Theater PC (HTPC) and are using an external
Audio Receiver for sound output, set a 200 millisecond delay on your audio output
for A/V sync. You will not experience A/V sync issues for anything other than
gaming or HTPC applications since the TV has internal A/V sync functionality.
Changing picture and sound settings
You must set [Home] in [ Location]. (Refer to page 30.)
Otherwise, personalized picture and sound settings will not be
memorized after the unit goes to standby mode.
Changing picture settings
1
Press MENU on the remote control.
2
Use О /п/Н /Ж to select [ Setup] > [ Picture].
Picture
Sound
Features
Installation
Software
Settings assistant Start now
Contrast
Brightness
Color
Tint
Sharpness
Color temperature Cool
Dynamic contrast Off
3
Use О /п/ Н /Ж to select one of the picture settings, and press OK
to enter the setting.
4
Adjust the picture quality.
The following picture settings can be confi gured. Depending on
the format of the picture source, some picture settings are not
available.
Setting items Description
Settings assistant
Use [ Settings assistant] to guide you through
the best picture settings.
Contrast
Adjusts the intensity of bright areas, keeping
dark areas unchanged.
Brightness Adjusts the intensity and details of dark areas.
Color Adjusts color intensity.
Tint Adjusts the color balance in an image.
Sharpness Adjusts the level of sharpness in image details.
Color
temperature
Cool More blue tones.
Normal Standard tones.
Warm More orange tones.
Dynamic
contrast
Off Sets Dynamic contrast to off.
On Automatically enhances contrast in an image.
Digital Natural
Motion
Off Sets Digital Natural Motion to off.
Minimum
Reduces judder in video using low intensity
frame interpolation to make the video smooth.
Maximum
Reduces judder in video using high intensity
frame interpolation to make the video smooth.
Noise
reduction
Off Sets Noise reduction to off.
On Reduces noise in an image.
MPEG artifact
reduction
Off Sets MPEG artifact reduction to off.
On
Reduces a blockiness and a blurriness and
judder by digital filter.
EN