Desa CB36N - Manual (Page 20)

www.desatech.com 117437-01D 0
O
FF
PIL
OT O
N
OPERATING FIREPLACE
MANUAL IGNITION SySTEM
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not fol-
low these instructions exactly,
a fire or explosion may result
causing property damage, per-
sonal injury or loss of life.
A. This appliance is equipped with an igni-
tion device which automatically lights
the pilot. Do not light pilot by hand.
B. BEFORE LIGHTING smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor's phone. Follow the
gas supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don't try to repair it, call a
qualified service technician. Force or
attempted repair may result in a fire or
explosion.
D. Do not use this appliance if any part
has been under water. Immediately call
a qualified service technician to inspect
the appliance and to replace any part of
the control system and any gas control
which has been under water.
LIGHTING
INSTRUCTIONS
1.. STOP!. Read. the. safety. information.
above.
.. Open.lower.louver.panel.
3. Turn off all electric power to the fireplace.
4.. Push.in.gas.control.knob.slightly.and.turn.
clockwise. .to.OFF.(see.Figure.33).
5. Wait five (5) minutes to clear out any
gas. Then smell for gas, including near
Figure 33 - Control Valve Millivolt
the floor. If you smell gas, STOP! Follow
“B”.in.the.safety.information.above..If.you.
don’t.smell.gas.go.to.the.next.step.
6.. The.pilot.is.located.by.the.main.burner.and.
should.not.require.accessing.for.lighting.
7.. Turn.gas.control.knob.counterclockwise.
.to.PILOT.
8.. Push.in.gas.control.knob.all.the.way.and.
hold..Immediately.light.the.pilot.by.repeat-
edly pressing the piezo ignitor until a flame
appears..Continue.to.hold.for.about.one.
(1). minute. after. the. pilot. is. lit.. Release.
gas.control.knob.and.it.will.pop.up..Pilot.
should remain lit. If it goes out, repeat
steps.5.through.8.
•.If.gas.control.knob.does.not.pop.up.when.
released, stop and immediately call your
service.technician.or.gas.supplier.
• If the pilot will not stay lit after several tries,
turn.gas.control.knob.to.OFF.and.call.your.
service.technician.or.gas.supplier.
9. Turn on all electric power to fireplace.
10..Turn.gas.control.knob.counterclockwise.
.to.ON.
11..To.leave.pilot.lit.and.shut.off.burners.only:.
turn.control.knob.clockwise. .to.the.
PILOT.position..Set.wall.switch.or.remote.
selector.switch.to.OFF.position.to.prevent.
draining.battery.
1..Close.lower.louver.panel.
Gas.Control.Knob
Regulator.Cap
Piezo Ignitor
TO TURN OFF GAS
TO APPLIANCE
1.. Open.lower.louver.panel.
.. Set.the.wall.switch.to.“OFF”.position.or.the.
HRC.selector.switch.(when.equipped).to.
prevent.draining.the.battery.
3.. Turn.off.all.electric.power.to.the.appliance.
if.service.is.to.be.performed.
4.. Push.in.gas.control.knob.slightly.and.turn.
clockwise. .to.OFF.
5.. Close.lower.louver.panel.
6.. Close.equipment.shutoff.valve.(see.Figure.
25, page 17).