Yamaha DTX-Multi12 Multi-Pad Electronic Percussion Instrument - Manual (Page 40)

40 Owner’s Manual
Internal Design
Parameter
name
Descriptions
DlyLvlC
This parameter is used to set the delay volume for the
center channel.
DlyMix
This parameter is used to set the mixing level for the
delayed sound.
DlyOfst
This parameter is used to set the modulation delay
time’s offset value.
Drive
This parameter is used to set the degree to which the
effect is applied.
DriveHorn
This parameter is used to set the depth of modulation
produced through rotation of the high-frequency horn.
DriveRotor
This parameter is used to set the depth of modulation
produced through rotation of the low-frequency rotor.
DstL.Gain
This parameter is used to set the degree by which the
low frequencies from the distorted sound are boosted or
cut.
DstM.Gain
This parameter is used to set the degree by which the
mid frequencies from the distorted sound are boosted or
cut.
Edge
This parameter is used to specify a curve that deter-
mines how the sound is distorted.
EQ1Freq
This parameter is used to set the cutoff frequency for the
EQ1 band (i.e., low shelving).
EQ1Gain
This parameter is used to set the gain for the EQ1 band
(i.e., low shelving).
EQ2Freq
This parameter is used to set the center frequency for
the EQ2 band.
EQ2Gain This parameter is used to set the gain for the EQ2 band.
EQ2Q
This parameter is used to set the resonance of the EQ2
band.
EQ3Freq
This parameter is used to set the center frequency for
the EQ3 band.
EQ3Gain This parameter is used to set the gain for the EQ3 band.
EQ3Q
This parameter is used to set the resonance of the EQ3
band.
EQ4Freq
This parameter is used to set the center frequency for
the EQ4 band.
EQ4Gain This parameter is used to set the gain for the EQ4 band.
EQ4Q
This parameter is used to set the resonance of the EQ4
band.
EQ5Freq
This parameter is used to set the cutoff frequency for the
EQ5 band (i.e., high shelving).
EQ5Gain
This parameter is used to set the gain for the EQ5 band
(i.e., high shelving).
ER/Rev
This parameter is used to set the relative volumes of
early reflections and reverberation.
F/RDpth
This parameter is used to set the front-to-rear pan depth
(and is valid only when PanDirectn is set to “Lturn” or
“Rturn”).
FBHiDmp
This parameter is used to set how the feedback sound
decays in the high-frequency band (with smaller values
corresponding to faster decay).
FBLevel
[Chorus effects, Delay effects, and TempoFlanger]
This parameter is used to set how much of the delay
sound is fed back into the effect’s input (with negative
values indicating that its phase is to be inverted).
[TempoPhaser]
This parameter is used to set how much of the phaser’s
output is fed back into its input (with negative values indi-
cating that its phase is to be inverted).
[Reverb effects]
This parameter is used to set the initial delay’s feedback
level.
FBLvl1
This parameter is used to set the feedback level for the
first delay sound.
FBLvl2
This parameter is used to set the feedback level for the
second delay sound.
FBTime This parameter is used to set the feedback delay time.
FBTime1
This parameter is used to set the delay time for feedback
delay 1.
FBTime2
This parameter is used to set the delay time for feedback
delay 2.
FBTimeL
This parameter is used to set the delay time for the left
feedback delay.
FBTimeR
This parameter is used to set the delay time for the right
feedback delay.
Feedback
This parameter is used to set how much of the effect’s
output is fed back into its input.
Fine1
This parameter is used to adjust the first fine-pitch set-
ting.
Fine2
This parameter is used to adjust the second fine-pitch
setting.
H.Freq
This parameter is used to set the center frequency of the
high-frequency EQ band.
H.Gain
This parameter is used to set the amount by which the
high-frequency EQ band is boosted or cut.
Height
This parameter is used to set the height of the simulated
room.
HiAtk
This parameter is used to set the amount of time that
elapses before compression is fully applied in the high-
frequency band.
HiGain
This parameter is used to set the output level of the high-
frequency band.
HiLvl This parameter is used to set the high-frequency level.
HiMute
This parameter is used to activate and deactivate high-
frequency muting.
HiRat
[MltBndComp]
This parameter is used to set the compression ratio for
the high-frequency band.
[Reverb effects]
This parameter is used to adjust the high-frequency
component.
HiTh
This parameter is used to set the input-signal level at
which the compressor starts to process the sound in the
high-frequency band.
HornF
This parameter is used to set the speed of rotation of the
high-frequency horn at the “fast” setting.
HornS
This parameter is used to set the speed of rotation of the
high-frequency horn at the “slow” setting.
HPF
This parameter is used to set the high-pass filter’s cutoff
frequency.
InitDly
This parameter is used to set the amount of time that
elapses before early reflections are produced.
InitDly1
This parameter is used to set the delay time for the first
delay.
InitDly2
This parameter is used to set the delay time for the sec-
ond delay.
InitDlyL
This parameter is used to set the delay time for the left-
channel delay.
InitDlyR
This parameter is used to set the delay time for the right-
channel delay.
InpMode
This parameter is used to switch between mono and ste-
reo input.
InpSelect This parameter is used to select an input.
L.Freq
This parameter is used to set the center frequency of the
low-frequency EQ band.
L.Gain
This parameter is used to set the amount by which the
low-frequency EQ band is boosted or cut.
L/RDiffuse
This parameter is used to set the difference between left
and right delay times in order to produce a more spa-
cious sound.
L/RDpth
This parameter is used to set the depth of the left-right
panning effect.
Lag
This parameter is used to set a time lag for delay times
specified in terms of note lengths.
LFODpth
[SPX Flanger, TempoFlanger, SPX Chorus, and Sym-
phonic]
This parameter is used to set the depth of modulation.
[Tempo Phaser]
This parameter is used to set the depth of phase modu-
lation.
LFODiff
This parameter is used to set the left-right phase differ-
ence between modulation waveforms.
Parameter
name
Descriptions